Summary of Contents for DINSHARE JC-6001
- Page 1 User Manual Cordless Chain Saw Model No.JC-6001 Please read this user manual carefully before using, and save it for future references.
- Page 2 Story about DINSHARE Founded in ����, DINSHARE has grown to a resource-integrated company integrating R&D, testing, production, and sales, owning a wide range of high-quality product lines. Born in a craftsman family, DINSAHARE founder DIN adheres to the advanced innovative concept and traditional craftsman spirit, designing hot sales cordless chainsaw, wining much popularity.
-
Page 3: Table Of Contents
Contents About the product � --------------------------------------------------------------- � �） Components ------------------------------------------------------------- � �） Accessories ---------------------------------------------------------------- � �） Optional accessories -------------------------------------------------- � �） Specifications ------------------------------------------------------------ � �） Symbols ------------------------------------------------------------------- � �） Intended use ------------------------------------------------------------- � Safety warnings ------------------------------------------------------------------- � �） General power tool safety warnings ------------------------------- �... - Page 4 About the product 1. Components � � � � � � � � � 4" Guide plate Guide chain Switch button Lock-off button Grip Hand protect Battery assembly switch Battery pack Sprocket cover - 1 -...
-
Page 5: Optional Accessories
CAUTION: These accessories or attachments are recommended for use with your DINSHARE tool specified in this manual. The use of any other accesso- ries or attachments might present a risk of injury to persons. Only use accessory or attachment for its stated purpose. -
Page 6: Specifications
About the product 4. Specifications Model No. JC-6001 Voltage 20 V Charge Time 1 Hour Battery Capacity 2.0 A/h / 4.0 A/h No-load Speed 13.4 ft/s G.W./N.W. 4.15 / 1.98 lbs Measurement 13.39 * 6.1 * 5.7 Inch Due to our continuing program of research and development, the specifications herein are subject to change without notice. -
Page 7: Symbols
About the product 5. Symbols The following shows the symbols used for the equipment. Be sure that you understand their meanings before use. Read instruction manual. Wear safety glasses. Wear ear protection. Wear helmet, goggles and ear protection. Do not expose to moisture. Maximum permissible cut length. -
Page 8: Safety Warnings
Safety Warnings 1. General power tool safety warnings Warning: Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury. Save all warnings and instructions for future reference. The term "power tool"... - Page 9 Safety Warnings �) Prevent unintentional starting. Ensure the switch is in the off-position before connecting to the power source and/or battery pack, picking up or carrying the tool. Carrying power tools with your finger on the switch or energizing power tools that have the switch on invites accidents.
- Page 10 Safety Warnings �.� Battery tool use and care �) Recharge only with the charger specified by the manufacturer. A charger that is suitable for one type of battery pack may create a risk of fire when used with another battery pack. �) Use power tools only with specifically designated battery packs.
-
Page 11: Cordless Chainsaw Safety Warnings
Safety Warnings 2. Cordless Chainsaw safety warnings �) Keep all parts of the body away from the saw chain when the chainsaw is operating. Before you start the chainsaw, make sure the saw chain is not contacting anything. A moment of inattention while operating chainsaws may cause entanglement of your clothing or body with the saw chain. - Page 12 Safety Warnings �) As a chainsaw user, you should take several steps to keep your cutting jobs free from accident or injury. � Maintain a firm grip, with thumbs and fingers encircling the chainsaw handles, if proper precautions are taken. Do not let go of the chainsaw. �...
-
Page 13: Important Safety Instructions For Battery
Goods Legislation requirements. �) Follow your local regulations relating to disposal of battery. ��) Use the batteries only with the products specified by DINSHARE. Installing the batteries to non-compliant products may result in a fire, excessive heat, explosion, or leak of electrolyte. -
Page 14: User Guide
User guide 1. Switch action CAUTION: � Before inserting the battery cartridge into the tool, always check to see that the switch trigger actuates properly and returns to the "Locked" position when released. � � �. Switch button �. lock-off button �... -
Page 15: Installing And Removing Saw Chain
User guide 2. Installing or removing saw chain CAUTION: Always be sure that the tool is switched off and the battery cartridge � is removed before installing or removing the saw chain. � Always wear gloves when installing or removing the saw chain. �... - Page 16 User guide �. Get the plate and chain ready. �. Install the plate (to align with the hole). �. Install the chain， at this time, fit �. Put on the plate cover. the saw chain as shown in the figure because it rotates in the direction of arrow.
- Page 17 User guide 3. Installing or removing battery cartridge CAUTION: Always be sure that the tool is switched off and the battery cartridge is removed before adjusting or checking function on the tool. 1.Button 2.Battery cartridge � To remove the battery cartridge, slide it from the tool while sliding the button on the front of the cartridge.
- Page 18 User guide �.� Battery protection system The tool will automatically stop during operation if the tool and/or battery are placed under one of the following conditions: � Overloaded: The tool is operated in a manner that causes it to draw an abnormally high current.
-
Page 19: Indicating The Remaining Battery
User guide 4. Indicating the remaining battery �.� Battery pack LED indicator There are three LED lights designed on the appliance that indicate the level of the remaining power in the battery pack. To know the remaining power in the battery pack, please check out the chart below. Remaining Status of Indicators Capacity... -
Page 20: Maintenance
MAINTENANCE CAUTION: Always be sure that the tool is switched off and the battery cartridge is removed before attempting to perform inspection or maintenance. Always wear gloves when performing any inspection or maintenance. Never use gasoline, benzine, thinner, alcohol or the like. Discoloration, deformation or cracks may result. -
Page 21: Change The Saw Chain
MAINTENANCE 2. Change the saw chain CAUTION: Always remove the battery cartridge and wear safety gloves when performing work on the saw chain. Change the saw chain when: � Mealy sawdust is produced when damp wood is cut; � The chain penetrates the wood with difficulty, even when heavy pressure is applied;... - Page 22 This warranty does not apply to damage from repairs made or attempt- ed by anyone other than DINSHARE, misuse, alterations, abuse, lack of maintenance, or accidents. Cordless chain saw need periodic parts replacement and service to achieve the best performance. This warranty does not cover the normal wear and tear with normal use, including but not limited to the surface of the chain saw.
-
Page 23: Contact Us
Contact Us If you have any questions or need any help, please feel free to contact us via email address: dinshare@afterservice.vip Extended warranty: Scan the QR code to get ��/� online customer service + extended �-year warranty! Scan here to contact us [��Hrs Online]... - Page 24 Scan here to contact us [24Hrs Online] https://dinshare.afterservice.vip...
Need help?
Do you have a question about the JC-6001 and is the answer not in the manual?
Questions and answers
I can't get my dinshare jc 6002 to work. I've used it for a couple of months and now it won't work at all even though both batteries are fully charged. What can I do?
If the DINSHARE JC-6001 is not working despite fully charged batteries, follow these troubleshooting steps:
1. Check the switch trigger: Ensure it actuates properly and returns to the "Locked" position when released.
2. Use the lock-off button correctly: To start the tool, press the lock-off button and then pull the switch trigger.
3. Verify battery compatibility: Only use genuine Dinshare batteries. Non-genuine or altered batteries may cause malfunction.
4. Inspect the battery: Do not use if the battery is damaged.
5. Ensure proper installation: Confirm the battery is inserted correctly and securely into the tool.
If the tool still does not operate, further inspection or professional service may be required.
This answer is automatically generated