Summary of Contents for Benner-Nawman BN Products BNG8000iD
- Page 1 MODEL: BNG8000iD INVERTER GENERATOR USER’S MANUAL 3450 Sabin Brown Road • Wickenburg, AZ 85390 (800) 992-3833 • mail@bnproducts.com BNG8000iD Owners Manual.indd Page | 1 BN Products-USA...
- Page 2 Thank you for choosing our inverter generator. This manual covers the proper operation and maintenance. Before operating, please read this manual carefully for import- ant procedures and safety. All technical data and drawings in this manual are consistent with the information on this product. As a result of revisions and other on going updates, the contents of this manual may be slightly different from the actual pr oduct.
-
Page 3: Safety Warning
Safety Warning Personal, product, and property safety of you and others is very important. Please read carefully the extremely important safety warnings contained in this manual and on the labels of this generator set. Safety warnings can alert you to potential dangers that may harm you and others. -
Page 4: Safety Instruction
1. Safety Instruction 1.1 Safety Specification Please read and understand this manual before operating. Familiarity with the safe operating procedures of generators can help you avoid accidents. BNG8000iD Owners Manual.indd Page | 4 BN Products-USA... - Page 5 1.2 Special Request • Electrical cords and plugs should be in good condition without exposed wires or connections. • A ground terminal is on this generator and shoud be connected to a ground wire. • Extension cords need to be the proper gauge for the distance they have to run.
- Page 6 2. Safety Warning Label Please read the manual carefully before using. Safety warning label BNG8000iD Owners Manual.indd Page | 6 BN Products-USA...
- Page 7 3. Components Identification 3.1 Components Features BNG8000iD Gas Generator BNG8000iD Owners Manual.indd Page | 7 BN Products-USA...
- Page 8 3.2 Control Panel Factory may adjust the panel for different configurations. Please note that the configuration is subject to change without prior notice. 1. Engine Oil Indicator Light 2. Overload Indicator Light 3. AC Indicator Light 4. 3-in-1 Digital Meter 5.
- Page 9 3.3 Type and Serial Number Type and serial number is listed on the side of engine Product Number Type Serial Number BNG8000iD Owners Manual.indd Page | 9 BN Products-USA...
- Page 10 4. Control System 4.1 Engine Oil Alerting System (RED) The engine oil protection system will stop the engine automatically, and the engine oil indicating light will light up when the oil in the crankcase is low. Fill the engine oil to the proper level to restart the engine.
-
Page 11: Ground Terminal
3. Check the cool air inlet for any blockage and clean the area if needed. 4. Restart the engine after checking. Notice: When using electrical equipment with high starting current (like compressors and sink pumps, etc.), the overload indicating light may flash for few seconds. But this is normal. 4.3 AC Indicator Light (GREEN) The AC indicator light will be on while the engine starts and has normal... - Page 12 5. Preparation 5.1 Fuel • Gasoline is flammable and toxic. Please read the safety instructions carefully before refueling.(See Page 7 for details.) • Do not fill the tank with too much fuel, or the fuel will overflow when the tank gets warm. •...
- Page 13 5.2 Engine Oil The generator is not filled with engine oil when leaving the factory. Please do not start it before filling engine with the required amount of oil. 5.3 Recoil Starter Pull the starter handle up gently until resistance is felt, then pull it out quickly.
- Page 14 After starting, please do not let the starting handle fly back in- place suddenly, but gently put the handle back. Recoil starter 5.4 Fuel Tap Fuel tap is a device that controls the flow of fuel from the tank to the carburetor. Turn the “4-in-1 switch” to the off position when not in use.
- Page 15 5.5 Choke Valve The choke valve is used to provide a rich mixture of fuel to a gasoline engine when the cold engine is started. When the cold gasoline engine starts, rotate the knob to the “RUN” position. When the gasoline engine starts up warm, the starting switch can be placed in the “RUN”...
- Page 16 6. Generator Use • Applicable temperature: 23° - 104° F (5° - 40° C) • Applicable humidity: below 95% • Applicable altitude: below 3300 ft (1000m). Lower power should be expected in areas above this altitude or contact the dealer to adjust the carburetor. 6.1 Connect to House Power Supply Connecting this generator to a home power supply is not rec- ommended.
- Page 17 6.2 Generator Grounded In order to prevent electrical appliances from being damaged, it is recommended to ground the generator with good conductors covered with insulation. 6.3 AC Output Before starting the generator, please confirm: The total load (the sum of all loads) should not exceed the rated power of the generator.
- Page 18 Generally speaking, motors require a large initial starting cur- rent. The following table is for your reference when connecting these electrical appliances to the generator set. 5.4 Use in High Altitude Areas At high altitudes, a standard carburetor will make the gasoline engine mixture too rich, and reduce the output power and increase the fuel consumption rate.
- Page 19 7. Starting the Generator 7.1 Recoil Start 1. Remove all loads from the output. 2. Rotate the start switch to put the start button at the “CHOKE” position. 3. Put the “ECO” switch in the OFF position. If the engine is already hot, move the start button to the “RUN”...
-
Page 20: Stopping The Generator
Do not crank the motor for more than 5 seconds at a time, otherwise the starting motor will be damaged. If the start is not successful, the interval between starts should be 10 sec- onds. If the starting motor speed has a noticable decline, it may indicate that the battery is low and should be removed and charged. -
Page 21: Maintenance
9. Maintenance Good maintenance is the best guarantee for the safe, and eco- nomical operation, and contributes to a cleaner environment protection. In order to keep the engine in good condition, you must check and maintain it regularly. Please follow the sched- ule below. - Page 22 • The engine oil should be replaced every 10 hours if work- ing frequently at high temperatures or loads. • The air filter element should be cleaned every 10 hours if operating in a dusty or dirty environment. If neces- sary,please replace it every 25 hours.
-
Page 23: Air Filter Maintenance
Prolonged and frequent exposure to oil can lead to skin cancer. While this is not a given, it is still recommended that you use soap and water to immediately and thoroughly wash any skin that has been exposed to oil. To protect the environment properly dispose of all waste oil. - Page 24 It is strictly forbidden to start the generator without the air fil- ter, otherwise it will lead to rapid wear and tear of the gasoline engine. • Turn the knob of the maintenance door to the “On” posi- tion, and remove the maintenance door. •...
- Page 25 10. Storing To avoid combustion due to contact with high-temperature components of the generator, the generator must be cooled before packaging and storage. If long-term storage is required, please make sure the storage area is clean and dry. • Drain fuel from the fuel tank.Clean the fuel filter, O - ring seal and precipitation cup.
- Page 26 11. Trouble Shooting BNG8000iD Owners Manual.indd Page | 26 BN Products-USA...
-
Page 27: Circuit Diagram
12. Circuit Diagram The factory can adjust according to the different model configurations, that are subject to change without prior notice. BNG8000iD Owners Manual.indd Page | 27 BN Products-USA... - Page 28 13. Technical Specifications BNG8000iD Owners Manual.indd Page | 28 BN Products-USA...
Need help?
Do you have a question about the BN Products BNG8000iD and is the answer not in the manual?
Questions and answers