Summary of Contents for Gateway Office Furniture STRETCH
- Page 1 Assembly Instructions & General Overview For Technical Assistance Please Call Conklin Office Furniture at 800.817.1187 or email support@conklinoffice.com...
- Page 2 1. General Overview & Assembly Order………………………...Page 3 2. Assembling the Structural Components……………………Page 4-11 3. Power, Data, Power Poles and Cable Floor Boxes……….Page 12-17 4. Worksurfaces and Screen Brackets…………………………….Page 18-24 5. Final Check………………………………………………………………..Page 25 For Technical Assistance Please Call Conklin Office Furniture at 800.817.1187 or email support@conklinoffice.com...
-
Page 3: General Overview
General Overview Stretch™ benching is a modular system designed to be easy to install and specify as well as being easily re-configured. At the core of the system are the legs and cable trays., which are able to extend or retract to accommodate multiple work surface lengths without specifying additional components. - Page 4 Structural Component Assembly (Cable Tray & Support Leg) Remove the two screws and flat plate from the receiver on the leg. Insert teeth on cable tray into receiving slots on leg. After inserting the teeth, the cable tray must be pushed down to lock the teeth into the leg (a rubber hammer may be used to assist).
- Page 5 Structural Component Assembly (Cable Tray & Support Leg) There are four types of main support legs (two types of single legs and two types of double legs). Single end legs are used at the end of runs or on both sides of a single free stand- ing desk.
- Page 6 Structural Component Assembly (Cable Tray & Support Legs) Single center legs are used in between desks in the middle of runs and have cable tray receivers on both sides. The double legs are used in the same manner as the single legs but are used for pods (back to back configuration) For Technical Assistance Please Call Conklin Office Furniture at 800.817.1187 or email support@conklinoffice.com...
- Page 7 Structural Component Assembly (Cable Tray & Support Legs) The double legs are used in the same manner as the single legs but are used for pods (back to back configuration) For Technical Assistance Please Call Conklin Office Furniture at 800.817.1187 or email support@conklinoffice.com...
- Page 8 Structural Component Assembly (Cable Tray & Support Legs) Under worksuface cable management can be added to return worksurfaces by using a 90 degree bracket. For Technical Assistance Please Call Conklin Office Furniture at 800.817.1187 or email support@conklinoffice.com...
- Page 9 Structural Component Assembly (Brace Legs) In addition to the main support legs there are four brace legs used for stabilizing when no return work surfaces are utilized. Brace legs are always installed perpendicular to End legs and Center legs Two of the legs are used for single sided run configurations and two of the legs are used for pod configurations.
- Page 10 Structural Component Assembly (Brace Leg Single & Double) The first two legs are used for single sided pods also know as runs ( Single Brace Leg & Double Brace Leg). See below for typical installation locations. Note: When return work surfaces are utilized brace legs are not necessary. For Technical Assistance Please Call Conklin Office Furniture at 800.817.1187 or email support@conklinoffice.com...
- Page 11 Structural Component Assembly (Brace Leg Quad & Back to Back) The other two legs are used for double sided pods (quad brace leg & brace leg back to back). See below for typical installation locations. Note: When return work surfaces are utilized brace legs are not necessary. For Technical Assistance Please Call Conklin Office Furniture at 800.817.1187 or email support@conklinoffice.com...
- Page 12 Power Components & Installation Below are the components that make up the power system. Power Bar with duplexes, slide mount brackets and jumper or base infeed. For Technical Assistance Please Call Conklin Office Furniture at 800.817.1187 or email support@conklinoffice.com...
- Page 13 Power Components & Installation Slide the brackets into the end of the cable tray as shown For Technical Assistance Please Call Conklin Office Furniture at 800.817.1187 or email support@conklinoffice.com...
- Page 14 Power Components & Installation Slide the power bar on to the clips until secure. For Technical Assistance Please Call Conklin Office Furniture at 800.817.1187 or email support@conklinoffice.com...
- Page 15 Power Components & Installation Connect base power infeed to power bar and connect jumpers between power bars. When power bars are in the desired location install the 4 securing screws that came with the cable tray. For Technical Assistance Please Call Conklin Office Furniture at 800.817.1187 or email support@conklinoffice.com...
- Page 16 Cable Floor Box & Power Pole (Cable Routing) The cable floor box is a hollow box elevated by four Legs to allow cabling to pass underneath and then up to the cable tray. The red line below shows the path of cable routing when coming from the wall or floor.
-
Page 17: Network Cable Installation
Network Cable Installation Network cables shown installed in power way after power raceways and duplexes have been installed. Center legs are cut out in the middle to allow cables to pass through to the next tray For Technical Assistance Please Call Conklin Office Furniture at 800.817.1187 or email support@conklinoffice.com... -
Page 18: Worksurface Installation
Worksurface Installation The main worksurfaces have threaded inserts pre-installed that match with the loca- tion of the holes on the primary Stretch legs. 6MM machine screws are used to attach the worksuface to the legs. For Technical Assistance Please Call Conklin Office Furniture... - Page 19 Worksurface Installation On end of runs worksurface edge should be flush with the Stretch leg. For Technical Assistance Please Call Conklin Office Furniture at 800.817.1187 or email support@conklinoffice.com...
- Page 20 Worksurface Installation Return worksurfaces are attached via wood screws and flat brackets to the main work surface. For Technical Assistance Please Call Conklin Office Furniture at 800.817.1187 or email support@conklinoffice.com...
- Page 21 Worksurface Installation Return worksurfaces are supported via a full height pedestal or with a single end leg. For Technical Assistance Please Call Conklin Office Furniture at 800.817.1187 or email support@conklinoffice.com...
- Page 22 Screen Bracket Installation Screen Brackets come with all parts necessary to install as a single sided application or double sided application. As well as tow sizes of rubber to accommodate either metal/fabric screens or glass screens. For Technical Assistance Please Call Conklin Office Furniture at 800.817.1187 or email support@conklinoffice.com...
- Page 23 Screen Bracket Installation (Single Sided Application) Thread bracket down until it clamps the worksurface. Install two woodscrews through 5 hole bar into bottom side of worksurface. Clip cosmetic bolt cover onto bolt as shown in the picture below Insert screen into bracket and fully tighten the two screws For Technical Assistance Please Call Conklin Office Furniture at 800.817.1187 or email support@conklinoffice.com...
- Page 24 Screen Bracket Installation (Double Sided Application) Single sided applications are installed as shown Bolt is centered in flat bar Install under surface with Thread bracket Fully thread bracket until bolt coming up between onto bolt it clamps the surfaces surfaces Install brackets 7”...
-
Page 25: Final Check
Final Check 1. Check tightness of leg to worksurface screws 2. Check that screen brackets are clamping screens with max clamping pressure 3. Check that screen brackets are fully tightened to the worksurface 4. Level all worksurfaces For Technical Assistance Please Call Conklin Office Furniture at 800.817.1187 or email support@conklinoffice.com...