P+P RescueRiggaMK2 User Instructions

Thank you for purchasing this P+P RescueRiggaMK2 Kit. Please take time to familiarize yourself with the correct use and operation.
It is imperative that this kit is only used for its intended purpose and that it is subject to a periodic recorded detailed inspection by a competent person.
To avoid personal injury, prior to using this P+P RescueRiggaMK2 Kit or training others to use it, CAREFULLY READ and understand these instructions.
If there is anything you do not understand DO NOT use the P+P RescueRiggaMK2 Kit, contact the supplier or P+P for further details.
Certain information in this manual is governed by law and is subject to change without prior notice. Great care has been taken to ensure that the
information is correct at the time of publication. However, it is the user's sole responsibility to ensure that they fully comply with all legal requirements.
P+P operate a policy of continual improvement and reserve the right to change specifications without notice. The Manufacturer and / or their recognised
agents, directors, employees or insurers will not be held liable for consequential or other damages, losses or expenses in the connection with or by reason
Description
The P+P RescueRiggaMK2 Kit is a pre-rigged rescue kit developed for
remote capture & retrieval of a suspended casualty. In most cases a
suspended casualty can be rescued without the need to climb.
The effective rope working length is not affected by the pulley system
and a 50 metre standard system gives an operational recovery length of
approximately 50 metres.
The RescueRiggaMK2 Kit comes complete with a 3.5m Remote capture
Pole & P+P Super Clip. This effective 'Z' rig system incorporates a 'Lory'
Descender. 2 single pulleys are mounted on a 'Paw plate', with Jammers
fitted to the rope to assist in lift recovery. The innovative 9:1 pulley
system allows the casualty to be either raised or lowered to a safe
position.
Function
The P+P RescueRiggaMK2 Kit must be used with a full body harness to
EN361 to provide a rescue recovery system
P+P recommend that users are trained in the proper use and
practical/physical limitations of this system. Equipment specifiers / users
must ensure this system is used with compatible ropes and connectors.
Failure to ensure compatibility may result in an unsafe condition or even
connector/link failure.
All work at height including the use of Personal Protective
Equipment (PPE) as a control measure is subject to a suitable and
sufficient risk assessment.
Product Conformance
Standard(s)
EN341 Descender device
EN1891 Low Stretch Kernmantle
Max. working load in rescue
Standard rope length*
Designers, Manufacturers and Suppliers of Quality Height
Safety & Rescue Equipment, Training & Consultancy
P+P RescueRiggaMK2 Kit
P+P will not accept liability for any inaccuracy or incorrectly stated legal requirements.
of or the inability to use the P+P RescueRiggaMK2 Kit for any other purpose.
.
Warning
150Kg
50m
P+P Limited, 131 New John Street, Aston, Birmingham B6 4LD England
Tel: +44 (0)121 359 4561 Fax: +44 (0)121 359 4136
e-mail: sales@ppsafety.co.uk website: www.ppsafety.co.uk
User Instructions
* Custom rope lengths are available upon request
Using the System
The RescueRiggaMK2 kit is for personal use only. Only use EN362
connectors & EN1891 11mm low stretch kernmantle approved by P+P.
Selection of a suitable anchorage point is critical and must in all cases be
above the casualty and capable of taking a peak force of 12kN. This is
usually a structural strong point or anchorage to BSEN 795.
Instructions for use
•
Safely access the casualty, ensuring that the rescuer is attached
to the structure at all times or is suitably protected from a fall.
•
Position rescue bag onto structure & lift out rescue system.
•
Select suitable anchorage for the RescueRiggaMK2 system.
•
Attach the RescueRiggaMK2 anchorage using the P+P sling &
Kwiklock karabiner ensuring the karabiner gate is closed.
•
Extend the remote capture pole & attach the 'pre-armed' P+P
Super Clip to the end. Ensure the karabiner gate is fully open
in the Super Clip.
•
Using the extended pole with attached clip carefully hook the
open gate of the karabiner over the casualty's harness D ring.
Ensure you hook the harness D ring & not the arresting device
connector
•
A sharp tug on the remote capture pole will leave the rescue
rope & hook attached to the casualty's harness D ring.
•
The Rescue Rigga is pre-rigged to raise the casualty by pulling
down on the free end of the rope using a Hand Jammer
(optional Extra) the rope will feed through the 'Z' rig for
approximately 1 m.
Registered in England No. 01493537
V2_1214
Warning