Summary of Contents for HungaroFLASH QUASAR SILENT PRO
- Page 1 QUASAR SILENT PRO 15 000 WATTS ! STROBE SETUP QUICKSTART GUIDE WWW.HUNGAROFLASH.COM...
- Page 2 QUASAR SILENT PRO MENU MAP - MENU MODE=0 (STANDARD MENU) UNPLUG THE STROBE AND SEE THE MANUAL TO UNLOCK BUTTONS NORMAL OPERATE DISPLAY INTENSITY=0 POWER REDUCTION = 1 EEPROM ERROR BUTTONS LOCKED MODE SETTINGS MENU AS IT WAS SET LAST TIME...
- Page 3 QUASAR SILENT PRO MENU MAP - MENU MODE=1 (EXTENDED MENU) UNPLUG THE STROBE AND SEE THE MANUAL TO UNLOCK BUTTONS NORMAL OPERATE DISPLAY INTENSITY=0 POWER REDUCTION = 1 EEPROM ERROR BUTTONS LOCKED MODE SETTINGS MENU AS IT WAS SET LAST TIME...
- Page 4 QUASAR SILENT PRO MENU MAP - MENU MODE=1 (EXTENDED MENU) UNPLUG THE STROBE AND SEE THE MANUAL TO UNLOCK BUTTONS NORMAL OPERATE DISPLAY INTENSITY=0 POWER REDUCTION = 1 EEPROM ERROR BUTTONS LOCKED TO BE CONTINUED FROM THE PREVIOUS PAGE MODE SETTINGS MENU AS IT WAS SET LAST TIME...
-
Page 5: Normal Dmx Mode
QUASAR SILENT PRO Main features QUASAR SILENT PRO - SETUP QUICKSTART GUIDE Please read the user manual toughly before operation! This equipment produces high intensity continuous or strobostic light effects with different setted modes and parameters. These settings are kept after turn-off the equipement. The six different DMX control mode, the built-in effects and the ANALOG mode ensure three type of stand alone wide range usage of the equipment. -
Page 6: Eeprom Error
QUASAR SILENT PRO Switching on and fixture status 2 - Power-on, mode status information The equipment determines the input frequency after every power-on and restart for the appropriate operation. If can not determines from some input-line half period mean (transients of input voltage, defective generator, damaged electronics), the equipment will repeat this measurement until gets a valuable result. - Page 7 QUASAR SILENT PRO MODE STTINGS MENU 3 - Setting the equipment, MODE SETTINGS MENU 3.1 - Normal strobe – two channels DMX controlled strobe mode 3.1.1 - Enter into menu After power-on press the ENTER button to get into MODE SETTINGS MENU unless the buttons are not locked.
- Page 8 QUASAR SILENT PRO MODE STTINGS MENU 3.2 - HF strobe - strobe mode controlled by 2 channel HF DMX protocol 3.2.1 - Enter into menu After power-on press the ENTER button to get into MODE SETTINGS MENU unless the buttons are not locked.
- Page 9 QUASAR SILENT PRO MODE STTINGS MENU 3.4 - Normal 4ch effect strobe - strobe controlled by DMX with build-in effects 3.4.1 - Enter into menu After power-on press the ENTER button to get into MODE SETTINGS MENU unless the buttons are not locked.
- Page 10 QUASAR SILENT PRO MODE STTINGS MENU 3.5 - HF 4ch effect strobe - strobe controlled by HF DMX with build-in effects 3.5.1 - Enter into menu After power-on press the ENTER button to get into MODE SETTINGS MENU unless the buttons are not locked.
-
Page 11: Repeat Rate
QUASAR SILENT PRO MODE STTINGS MENU 3.6 - ANALOG - stand alone mode with settable Repeat-, flash time and light intensity 3.6.1 - Enter into menu After power-on press the ENTER button to get into MODE SETTINGS MENU unless the buttons are not locked. -
Page 12: Effect Speed
QUASAR SILENT PRO MODE STTINGS MENU 3.7 - ANALOG EFFECT - stand alone mode with settable effect speed, effect type and light intensity 3.7.1 - Enter into menu After power-on press the ENTER button to get into MODE SETTINGS MENU unless the buttons are not locked. - Page 13 QUASAR SILENT PRO MODE STTINGS MENU 3.8 - Normal 2CH Effect strobe - DMX controlled strobostic mode with effects 3.8.1 - Enter into menu After power-on press the ENTER button to get into MODE SETTINGS MENU unless the buttons are not locked. Select the submenu with UP/DOWN buttons. Press again the ENTER button to reach the preferred parameter.
- Page 14 QUASAR SILENT PRO MODE STTINGS MENU 3.9 - HF 2CH effect strobe - HF DMX controlled strobostic mode with effects 3.9.1 - Enter into menu After power-on press the ENTER button to get into MODE SETTINGS MENU unless the buttons are not locked.
-
Page 15: Display Intensity
QUASAR SILENT PRO MODE STTINGS MENU 3.10 - Fixture Settings - setting the basic parameters of the equipment 3.10.1 - Enter into menu After power-on press the ENTER button to get into MODE SETTINGS MENU unless the buttons are not locked. Select the submenu with UP/DOWN buttons. Press again the ENTER button to reach the preferred parameter. - Page 16 END OF THE DOCUMENT WWW.HUNGAROFLASH.COM...
Need help?
Do you have a question about the QUASAR SILENT PRO and is the answer not in the manual?
Questions and answers