Summary of Contents for gallaria ALTACOMFORT+ AT210
- Page 1 OPERATION ALTACOMFORT+ WALL FACE PAN INSTRUCTIONS CODE: AT210 intelligentbathrooms...
-
Page 2: Explanation Of Symbols
. CAUTION DANGER Gallaria shall not be liable for any loss arising from the failure to comply with the following: Refers to a potentially dangerous 1. This toilet is considered to be a Class I (1) -
Page 3: Safety Advice
SAFETY ADVICE To avoid the risk of electric shock, short- circuiting, fire, water leakage and damage to the product: DO NOT Insert or remove power plug with wet hands. DO NOT damage the power cord and plug. Inspect both before installation to ensure all is intact. - Page 4 ALTACOMFORT+ (AT210) Specifications Carbon filtration intelligentbathrooms...
-
Page 5: Technical Drawing
TECHNICAL DRAWING intelligentbathrooms... - Page 6 OVERVIEW intelligentbathrooms...
-
Page 7: Remote Control
REMOTE CONTROL Note: - The remote control requires 2 x AAA batteries (type 1.5V LR3/AAA) - which are not included. TAKE NOTICE - Software version : V1.0. Software updates will not be provided. intelligentbathrooms... -
Page 8: Explanation Of Functions
EXPLANATION OF FUNCTIONS Rear Wash Female Wash WASH MODES Press the ‘Wash’ button on the remote control or on the control knob. The bidet seat will commence washing. Washing can be stopped by simply pressing the ‘Stop’ button on either the remote control on control knob. - Page 9 EXPLANATION OF FUNCTIONS WASH FLOW RATE Alternatively, the wash flow rate can be controlled via the control knob. The flow rate will increase in the clockwise direction and decrease in the anticlockwise direction. During the washing process, press the ‘Adjust flow’ button on the remote control to either decrease or increase the wash flow rate.
- Page 10 EXPLANATION OF FUNCTIONS DRYING TEMPERATURE During the drying process, repeatedly press the ‘Adjust temperature’ button on the remote control until ‘Air temperature’ icon is highlighted, then press ‘Increase’ or ‘Decrease’ button to adjust the air temperature. Alternatively press the control knob and rotate it clockwise direction to increase the temperature and anticlockwise to decrease the temperature.
- Page 11 EXPLANATION OF FUNCTIONS SOUND/BEEP SETTINGS Open the cover and seat. Push control knob and turn: - In a clockwise direction to turn on - In an anticlockwise direction to turn off Note: Sound is turned on by default. USER SETTINGS To Save Once all desired settings have been set, press and hold down either the ‘User 1’...
- Page 12 BATTERY REPLACEMENT OF REMOTE CONTROL The remot control requires 2 x AAA batteries (type 1.5V LR3/AAA) When the User lights flash continuously, this is an indication that the batteries should be replaced. intelligentbathrooms...
- Page 13 GENERAL CARE & CLEANING ADVICE TOILET PAN COMFORT+ SEAT Soft, lint free cloths Soft, lint free cloths Non-abrasive, mild cleaning Low acidic cleaning agents agents Toilet brush SUGGESTED INTERVAL SUGGESTED CLEANING ACTIVITY Daily Wipe down water droplets with a soft lint free cloth to avoid limescale stains.
-
Page 14: Nozzle Cleaning
NOZZLE CLEANING The nozzle will automatically clean itself before washing and after washing. Should you wish to clean the nozzle manually, please do as follows: A. Open the cover and seat B. Rotate the knob in a clockwise direction C. -
Page 15: Filter Replacement
FILTER REPLACEMENT The filter has a service life of approximately 6 months. Naturally, this is dependent on the harshness of water the filter is subjected to. If the filter is not replaced at the suggested interval of 6 months, then we recommend that it be replaced when the wash flow is noticeably reduced. -
Page 16: Draining The Water Tank
DRAINING THE WATER TANK 1. The water and power must be cut before you disassemble the Comfort+ Seat 2. Do not invert or tilt the Comfort+ Seat before you finish draining the water tank DANGER 1. Turn the plug to the "OPEN" position and pullout. - Page 17 RELEASING AND REASSEMBLING THE COVER AND SEAT intelligentbathrooms...
-
Page 18: Troubleshooting
TROUBLESHOOTING The wash function is not working The drying function is not working intelligentbathrooms... - Page 19 When replacing old appliances with new ones, the retailer is legally obligated to take back your old appliance for disposals at least free of charge. For further information or help, please contact us: (02) 8985 2619 Head Office: 27 Helles Avenue, Moorebank, NSW 2170 www.gallaria.com.au intelligentbathrooms...