Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Summary of Contents for dispomed Highdent intro+
- Page 1 MANUAL RECEPTION + OPERATION + MAINTENANCE by par Dispomed www.dispomed.com...
-
Page 2: Table Of Contents
Handpieces Adjustments ................. 12 Assembled View ..................13 Controls Details ..................14-15 Units head ............ 14 Compressor ..........15 Daily Verifications Procedures ..............16-17 Annual Maintenance ................18 Kruuse – Intro ..................19 Warranty ..................... 20 Highdent is a trademark of Dispomed Ltd. 805-0260-250... -
Page 3: User Responsibility
Dispomed and by Dispomed trained personnel. The product must not be altered without the prior written approval of Dispomed. The user of this product shall have the sole responsibility for any malfunction which results from improper use, faulty maintenance, improper repair, damage, or alteration by anyone other than a qualified Dispomed technician. -
Page 4: The Highdent Intro Dental Delivery Unit
THE HIGHDENT INTRO ™ DENTAL DELIVERY UNIT. by par Dispomed Standard features include: Air/water syringe • 1 water bottle • Handpiece guard • Instrument platter • Product dimensions: Length: 43.2 cm (17”) • Width: 52.1 cm (20.5”) • Min. height: 79 cm (31”) •... -
Page 6: Receiving, Assembly And Start-Up
RECEIVING, ASSEMBLY AND START-UP INSTRUCTIONS. by par Dispomed Your Highdent dental unit requires some assembly before being used. Receiving To keep the possibility of damage during shipment to a minimum, the KRUUSE unit requires some assembly. All accessories are included in a bag and or small box within the shipping crate. - Page 7 RECEIVING, ASSEMBLY AND START-UP INSTRUCTIONS. by par Dispomed Check the compressor oil level through the sight If the oil level is less than half, remove the sticker and glass at the front of the compressor. fill the reservoir slowly by pouring a small quantity of oil at a time.
- Page 8 RECEIVING, ASSEMBLY AND START-UP INSTRUCTIONS. by par Dispomed Install handpieces: Fill water bottle with distilled water and install under head of unit by inserting drive tube and screwing 1: Low speed hanpiece bottle into place. 2: High speed handpiece 3: Piezo...
- Page 9 RECEIVING, ASSEMBLY AND START-UP INSTRUCTIONS. by par Dispomed Connect the other end of the power line from the Turn compressor on. (On units equipped with oil head assembly. Connect power cord from bottom of compressor the switch is near the pressure gauge at terminal strip to appropriate electrical outlet.
- Page 10 RECEIVING, ASSEMBLY AND START-UP INSTRUCTIONS. by par Dispomed Turn water valve on. Test syringe by pressing air button then water button then both simultaneously for mist. To sterilizee the tip pull it out of the syringe. Remove Piezo from holder.
- Page 11 RECEIVING, ASSEMBLY AND START-UP INSTRUCTIONS. by par Dispomed Remove low speed handpiece from holder. Use the indicated switch to activate the water the low speed handpiece. Position the handpiece selector to low speed. The water on the low speed handpiece is optionnal.
-
Page 12: Handpieces Adjustments
HANDPIECES ADJUSTMENTS. by par Dispomed Adjust handpieces pressure according manufacturers specifications. High speed handpiece pressure adjustment Low speed handpiece pressure adjustment 805-0260-250... -
Page 13: Assembled View
ASSEMBLED VIEW. by par Dispomed 805-0260-250... -
Page 14: Controls Details
UNIT CONTROLS DETAILS. by par Dispomed Handpiece pressure gauge Piezo power adjustment Handpiece selection Air / water syringe Piezo scaler (For detailed instruction on the piezo handpiece refer to the operation manual supplied with the piezo) High speed handpiece Low speed handpiece... -
Page 15: Compressor
COMPRESSOR CONTROLS DETAILS. by par Dispomed Auto/off Regulator adjustment Moisture trap Oil filter Compressor drain Compressor pressure gauge Over pressure valve Delivery pressure gauge (80 psi / 5.5bar) 805-0260-250... - Page 16 DAILY MAINTENANCE PROCEDURE. by par Dispomed A properly maintained machine reduces air consumption and extends the life time of the unit. Prerequisites: Air supply : 5.5 bar (75 to 85 P.S.I) – Electrical : 230 vac. Lubricate your handpieces as per your manufacturers Never lubricate the Piezo.
- Page 17 DAILY MAINTENANCE PROCEDURE. by par Dispomed Unplug your compressor at the end of the day and drain If the oil level is less than half, Fill the reservoir slow- all pressure by loosening the hand tight nut below ly by pouring a small quantity of oil at a time. Wait air reservoir.
-
Page 18: Annual Maintenance
ANNUAL MAINTENANCE. by par Dispomed An annual preventive maintenance is recommended. The maintenance consists of replacing all filter elements, changing the oil in the compressor, checking for leaks, resetting pressures and complete performance analysis. Contact your Highdent supplier for further details. -
Page 19: Warranty
Service & information center according to instructions and that the prescribed Dispomed Ltd. is proud to offer its customers an maintenance and service are performed. on-line or telephone service to answer questions Dispomed Ltd. - Page 20 DISPOMED CONTACT INFORMATION 745, Nazaire-Laurin, Joliette (Qc) Canada J6E 0L6 T : 1 800 363-1746 T : 1 450 759-9395 F : 1 450 759-8181 Courriel : info@dispomed.com Site internet : www.dispomed.com Twitter : twitter.com/dispomed_fr Facebook : www.facebook.com/dispomed...
Need help?
Do you have a question about the Highdent intro+ and is the answer not in the manual?
Questions and answers