Nicolas Holiday HS15-70-5T Important Safety Instructions

MODEL NO. HS15-70-5T
FOR INDOOR AND OUTDOOR USE
IMPORTANT SAFETY
INSTRUCTIONS
When using electrical products, basic precautions should always be
followed including the following:
READ AND FOLLOW ALL
a)
SAFETY INSTRUCTIONS.
b) Do not use seasonal products outdoors unless marked suitable for
indoor and outdoor use. When products are used in outdoor
applications, connect the product to a Ground Fault Circuit Interrupting
(GFCI) outlet. If one is not provided, contact a qualified electrician for
proper installation.
c) This seasonal use product is not intended for permanent installation
or use.
d) Do not mount or place near gas or electric heaters, fireplaces,
candles or other similar sources of heat.
e) Do not secure the wiring of the product with staples or nails, or place
on sharp hooks or nails.
f) Do not let lamps rest on the supply cord or on any wire.
g) Unplug the product when leaving the house, when retiring for the
night, or if left unattended.
h) This is an electric product-not a toy! To avoid risk of fire, burns,
personal injury and electric shock it should not be played with or placed
where small children can reach it.
i) Do not use this product for other than its intended use.
j) Do not hang ornaments or other objects from cord, wire, or light string.
k) Do not close doors or windows on the product or extension cords as
this may damage the wire insulation.
l) Do not cover the product with cloth, paper or any material not part of
the product when in use.
m)This product is equipped with push-in type lamps. Do not twist lamps.
n) This product employs overload protection (fuse). A blown fuse
indicates an overload or short –circuit situation. If the fuse blows,
unplug the product from the outlet. Also unplug any additional strings
or products that may be attached to the product. Replace the fuse as
per the user servicing instructions (follow product marking for proper
fuse rating) and check the product. If the replacement fuse blows, a
short-circuit may be present and the product should be discarded.
o) Read and follow all instructions that are on the product or provided
with the product.
SAVE THESE INSTRUCTIONS
p)
USE AND CARE INSTRUCTIONS
a) When the product is placed on a live tree, the tree should be well
maintained and fresh. Do not place on live trees in which the needles
are brown or break off easily. Keep the tree holder filled with water.
b) If the product is placed on a tree, the tree should be well secured and
stable.
c) Before using or reusing, inspect product carefully. Discard any
products that have cut, damaged, or frayed wire insulation or cords,
cracks in the lampholders or enclosures, loose connections, or
exposed copper wire.
d) When storing the product, carefully remove the product from wherever
it is placed, including tree, branches, or bushes, to avoid any undue
strain or stress on the product conductors, connections, and wires.
e) When not in use, store neatly in a cool, dry location protected from
sunlight.
USER SERVICING INSTRUCTIONS
Replace the fuse.
a) Grasp plug and remove from the receptacle or other outlet device.
Do not unplug by pulling on cord.
b) Using a flathead screwdriver, open fuse cover. Slide open the fuse
access cover on top of attachment plug towards blades.
c) Remove fuses carefully.
d) Risk of fire. Replace fuse only with 3 Amp,
125 Volt fuse (provided with product).
e) Close fuse cover. Slide closed the fuse
access cover on top of attachment plug.
f ) Risk of fire. Do not replace attachment plug. Contains a safety
device (fuse) that should not be removed. Discard product if the
attachment plug is damaged.
-SEE OTHER SIDE-
-CONTINUED FROM OTHER SIDE-
Replace the lamp.
Step 1: Grasp plug and remove from the
receptacle or other outlet device.
Do not unplug by pulling cord.
Step 2: Pull lamp and plastic base straight
out of lampholder.
Step 3: Replace lamp with only 3.3 Volt, 0.066 Watt, LED type lamp
(provided with product).
If the new lamp base does not fit in lampholder, follow the steps below step 3.
a) Remove the base of burned out lamp by straightening lamp leads and
gently pull lamp out.
b) Thread leads of new lamp through holes in old base with one lead in
each hole.
c) After lamp is fully inserted into base, bend each lead up, like other
lamps in the light set so that the leads will touch the contacts inside
the lampholder.
CAUTION:
1.This lighting string is rated 21.6 Watts ( 0.18
Amps),do not overload. Connect other lighting strings or decorative outfits
end-to end up to a maximum of 216 Watts (1.8 Amps) total.
lf connecting to a lighting string that does not have a Wattage (W) rating
{found on the tag within 6 inches of the plug} calculate the wattage as follows:
Multiply the current(_____A) which is on the flag-type tag by 120.
For Example: Lighting string is rated 120V, 60 Hz, 0.2 Amps.
0.2×120=24 Watts
Add the wattage of each light string together for a total of 216 Watts
or less. (Do not exceed 216 Watts.)
2. a) replace lamps only with3.3 volt, 0.066 watt spare lamps provided
with product. b) Risk of fire. This product does not contain lamp shunts,
which allow the product to operate if one lamp burns out. Do not replace
lamps with other than the spare lamps provided with this product. c) DO
NOT OPERATE WITH BULBS MISSING FROM SOCKETS. MISSING
BULBS SHOULD BE REPLACED PROMPTLY.
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including
interference that may cause undesired operation.
Warning:
Changes or modifications to this unit not expressly
approved by the party responsible for compliance could void the user's
authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
For questions and /or assistance, call customer service at 1-877-398-7337
or visit us on the web at www.geholidaylighting.com
©
2021 Nicolas Holiday Ltd. 204 Spring Hill Road Trumbull, CT 06611
9F., No. 37, Guangfu North Rd. Taipei, Taiwan 10560
All rights reserved.
TROUBLE SHOOTING
PROBLEM POSSIBLE CAUSE
If the One or more of the
product based LEDs may have
does not loosened from the
light socket during
transporting. There is a
break in the circuit
between the LED leads
and the socket
terminals. Fuse(s) may
have moved.
If a based One or more of the
LED is based bulbs may have
missing come out of the socket
when transporting.
If an LED Incorrect LED,
shorts or premature LED failure or
opens voltage is too high.
SH-21 PRINTED IN CHINA
CORRECTIVE ACTION
Unplug the set at the outlet.
Starting with the first unlit LED,
gently push (don't twist) each
LED base firmly into the socket.
If still does not light, then
remove each based LED and
check for out of place lead
wires. Open fuse door and
check fuses.
Mark socket(s) with a piece of
tape and unplug the set.
Replace the based LED or use
one of the spare based LEDs
included with product.
The LED may be out or dimly
lit. Replace bad LEDs as
soon as you find them.