Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Sanique S-9
Summary of Contents for Sanique S-9
- Page 1 S-9 SANITISING ELECTRIC SPRAYER USER MANUAL...
- Page 2 Sanique S-9 Electric Sanitising Sprayer CAUTION This manual contains important warnings and information PLEASE READ & KEEP FOR FUTURE REFERENCE VERSION S9-01-0420 Sanique 2b Stephenstown Industrial Park, Balbriggan, County Dublin, Ireland Declares that the Sanique S-9 Electric Sanitising Sprayer is in compliance with the regulations included in:...
-
Page 3: Quick Check
The information on this page is intended only as a quick guide. It is no way intended as a substitute to the information on the pages following, which the user should be fully acquainted with before using a Sanique sanitising sprayer. SYMPTOM... - Page 4 USE TO SPRAY Most sprayable disinfectants and other sanitising fluids PERFORMANCE Flow 2.9 ltr/min 3000 psi SPECIFICATION Motor 1300 watt Weight 34.85 kg (complete) Warranty 2 years SUPPLIED COMPLETE WITH Sanitising spray gun Sanitising spray lance Gold sanitising atomisation tip 1/4”...
- Page 5 SANIQUE S-9 Pressure control knob Sanitising spray lance On/off switch 15m hose assembly Sanitising spray gun Prime valve Gold sanitising atomisation Suction tube...
- Page 6 WARNING! Read and understand all instructions. Failure to follow all instructions listed below may result in electric shock, fire and / or serious personal injury. The term Sanique sprayer in all of the warnings listed below refers to your mains-operated (corded) sprayer.
-
Page 7: Specific Safety Rules
+ Have your Sanique sprayer serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the sprayer is maintained. If the supply cord of your Sanique sprayer is damaged it must be replaced by a specially prepared cord available through the service organization. - Page 8 MEDICAL ALERT INJECTION INJURIES If any solution appears to penetrate your skin, GET EMERGENCY MEDICAL CARE AT ONCE. DO NOT TREAT AS AN ORDINARY CUT. High pressure fluids from spray or leaks are powerful enough to easily penetrate the skin and cause extremely serious injection injury, leading to the possible need for amputation.
- Page 9 NEVER LEAVE SPRAYER UNATTENDED WITH PRESSURE IN THE SYSTEM. FOLLOW PRESSURE RELIEF PROCEDURES AT ALL TIMES. ALWAYS INSPECT SPRAYING AREA + Keep the spraying area free from obstructions. + NEVER keep flammable material in spraying area. + NEVER spray in vicinity of open flame or other sources of ignition. + The spraying area must be at least 6 metres away from spray unit.
-
Page 10: Operation
PACKINGS The packings are a wearing part. If your Sanique sprayer can no longer maintain pressure, has difficulty priming and tightening the packing nut no longer helps, then the packings will require replacement. This is best entrusted to a qualified... -
Page 11: Pressure Relief Procedure
Disengage the gun safety latch and you are ready to spray. PRESSURE RELIEF PROCEDURE IMPORTANT! To avoid possible serious body injury, always follow this procedure whenever your Sanique sprayer is shut off, when checking it, and whenever you stop spraying. Engage the gun safety latch. -
Page 12: Fluid Pump
Fluid Pump Suction Filter Quick reference MESH/THREAD PRODUCT CODE 15 mesh / 1/2” thread QF0535015B 30 mesh / 1/2” thread QF0535030B 60 mesh / 1/2” thread QF0535060B... - Page 13 Fluid Pump ITEM PRODUCT CODE DESCRIPTION Quick ref table INLET STRAINER/SUCTION FILTER (20MESH) 12-290-001 GLAND NUT 12-290-002 SUCTION TUBE (Ø12 x Ø22 x 315MM) 12-290-003 TUBE HOLDER (Ø11/Ø22) 12-005* O-RING (Ø28.4xØ35.3x3.5) 12-006* LOWER CHECK BALL (Ø12.7) 12-007 BALL GUIDE/CAGE 12-290-010 PUMP HOUSING 12-003 OUTPUT NIPPLE (PT 1/4"...
-
Page 14: Motor & Gearbox
Motor & Gearbox ITEM PRODUCT CODE DESCRIPTION 12-290-032 RETAINING RING (Ø1.2xØ24.8) 12-290-034 DRIVE WRIST PIN (Ø16x32) 12-290-033 PUMP WRIST PIN (Ø9.5x25) 12-290-035 DRIVE PISTON 12-290-038 INTERNAL CIRCLIP 12-290-039 BUSHING (Ø38xØ44x43) 12-290-051 SOCKET CAP SCREW (M5x35xP0.8) 12-290-050 GEAR HOUSING 12-290-053 BALL BEARING 12-290-054 TRUSS HEAD MACHINE SCREW (M5x8xP0.8) 12-290-055... - Page 15 Control ITEM PRODUCT CODE DESCRIPTION 70-1 12-290-091-1 ELECTRONICS UNIT (110V) 70-2 12-290-091-2 ELECTRONICS UNIT (220V) 12-290-121 RUBBER PROTECTION GUARD 12-290-101 PANHEAD TAPPING SCREW-B (M4x12) 12-290-097 EARTHING MARKING 12-290-096 PANHEAD MACHINE SCREW (M4x10xP0.7) 12-290-093 SOCKET CAP SCREW (M4x12xP0.7) 12-290-090 CONTROL BOX 12-290-094 U-BRACKET 12-290-092...
- Page 16 Fluid Manifold Manifold Filter Quick reference MESH/COLOUR CODE 15 mesh / grey QF0571030 60 mesh / black QF0571060 100 mesh / blue QF0571100 200 mesh / red QF0571200 ITEM PRODUCT CODE DESCRIPTION Quick ref table MANIFOLD FILTER 12-290-070 FILTER CAP 12-001 PACKING NUT TOMMY BAR 12-290-085...
- Page 17 Frame ITEM PRODUCT CODE DESCRIPTION 12-290-160 END CAP 12-290-153 HEX BOLT (M6x16xP1.0) 12-290-152 FLAT WASHER (Ø1/4xØ32x2) 12-290-154 WHEEL 12-290-155 EXTERNAL CIRCLIP (S-19) 12-290-156 FRAME 12-290-157 FLAT HEAD MACHINE SCREW (M4x5xP0.7) 12-290-158 HANDLE MOUNT 12-290-159 ROLL PIN (Ø5x25) 12-290-161 HANDLE...
- Page 20 Sanique UK & Europe 2b Stephenstown Industrial Park Balbriggan County Dublin Ireland K32 KV26 Australia 27 Tatura Avenue Gosford NSW 2250 Email sales@sanique.co.uk www.sanique.co.uk www.sanique.com.au Phone UK 01494 360751 Ireland 1800 714005 Australia 1300 229 757 International +353 1690 3162...