Ilumnia Vocalis User Manual
  1. Manuals
  2. Brands
  3. Ilumnia Manuals
  4. Speakers
  5. Vocalis
  6. User manual

Ilumnia Vocalis User Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
V o c a l i s

Advertisement

Table of Contents
loading

Related Manuals for Ilumnia Vocalis

Summary of Contents for Ilumnia Vocalis

  • Page 1 V o c a l i s...

  • Page 3: Table Of Contents

    Ilumnia Vocalis Contents page CONTENTS SAFETY INFORMATION UNPACKING RECOMMENDED SPEAKER SETUP SPEAKER CONDITIONING & BREAK IN CLEANING LAYOUT & FUNCTIONS : REAR PANEL CONNECTING PLAYING LIMITED WARRANTY SPECIFICATIONS User manual V1.0.1...

  • Page 4: Safety

    Ilumnia Vocalis Congratulations on your new Ilumnia speakers. These speakers incorporate the unique LEMS technology only found in Ilumnia loudspeakers. However, this technology requires some extra attention from its owner. To enjoy them to their fullest potential it’s imperative to invest a little bit of your time to read this manual.

  • Page 5: Information

    Ilumnia Vocalis Information Unpacking Due to the specific nature of these speaker’s geometry the necessary attention has to be given to unpacking / repacking. UNPACKING PROCEDURE Follow these steps : WARNING : Avoid touching the cone during these operations! 1. Place the carton box flat (horizontal) on one of its sides so that the bottom of the box is accessible.
  • Page 6 Ilumnia Vocalis 3. Place the carton back up so that the Ilumnia logo is in horizontal position and the “UP” arrow is pointing upwards to the ceiling. 4. Now lift the carton box slowly upwards so that the speaker including the EPS packaging slips out of the carton box from the bottom.
  • Page 7 Ilumnia Vocalis 6. Remove the other EPS packaging parts from the speaker. 7. Remove the protection bag from the speaker 8. Remove the fixing foam part between tweeter and LEMS driver by gently sliding it from the phase plug. Do not break or throw away this protective piece. Otherwise it will be impossible to further...

  • Page 8: Recommended Speaker Setup

    Ilumnia Vocalis Recommended Speaker Setup 1. Positioning Correct speaker placement has a huge impact on sound quality. Every room has its optimal layout for positioning the speakers. In this part of the manual we will give you some guidelines to position the speakers but the result of these guidelines will strongly depend on your rooms acoustical properties and dimensions.
  • Page 9 Ilumnia Vocalis 2. Bass Ports The Ilumnia Vocalis has an (optional) adaptable bass reflex front loaded port. This port constitutes of 2 parts, the inner and outer tube. To change the tuning of its frequency you can shove the inner tube backwards or remove it completely.

  • Page 10: Speaker Conditioning & Break In

    Ilumnia Vocalis Speaker Conditioning and Break-in Although a break-in period is not required, we recommend that you play between 100 to 150 hours of music through the speakers before doing any critical listening or speaker placement. The LEMS driver does not have a break-in period at all because it does not have any parts which are prone to strain like spider and surround.

  • Page 11: Cleaning

    Ilumnia Vocalis Speaker Cleaning DISCLAIMER : Ilumnia BVBA cannot be held responsible for damage caused to the speakers by any of the procedures described in this user manual. Physically touching the cone always involves a certain risk of damaging it and the only way to avoid damage is by not touching it at all.
  • Page 12 Ilumnia Vocalis If there’s a hint of scraping / scrubbing sound coming from one of the LEMS drivers. First thing to do : DON’T PANIC, it’s not broken Most likely a tiny piece of dirt or excessive dust has nested between the outside of the aluminium closing ring of the cone and the inside of the outer chassis ring of the driver.
  • Page 13 Ilumnia Vocalis WARNING : Make sure the cone doesn’t turn around !!! Slice of paper There is no harm in dust or dirt falling into the decompression chamber. It has been designed with sufficient clearance between cone and bottom. User manual...

  • Page 14: Layout & Functions : Rear Panel

    Ilumnia Vocalis Layout & functions : rear panel 1. On / Standby switch with integrated IEC Power supply entry (110-120V/60Hz or 220- 240V/50Hz depending on country, see power connection on speaker for the right voltage) • This switch is used to switch the speakers to “standby” mode. After turning the switch to “0”...
  • Page 15 Ilumnia Vocalis ❶ ❸ ❷ ❶ On / Standby switch with integrated IEC Power supply entry ❷ Speaker binding posts ❸ Low frequency equalization rocker switch Connecting your speakers STEP 1 Connect the RED(+) and BLACK(-) signal terminals (❷) of the left speaker to the amplifiers left channel.
  • Page 16 Ilumnia Vocalis ❸ 3 position rocker switch. This switch controls the energy in mid-low frequencies as shown in the graph below. All indications below are when the user is behind the speaker and looking at the back of the speaker.
  • Page 17 Ilumnia Vocalis Playing music Switch “on” (marked “1”) both speakers at the back of the speakers before playing any music. Important remark : if the speakers are cut off the mains or in standby mode only the tweeters of the speakers will work.

  • Page 18: Limited Warranty

    4. A service repair or replacement cannot exceed the value of the product under warranty, in no event shall Ilumnia BVBA be responsible or liable for special, incidental, consequential or indirect damages or losses. 5. Damages caused by incorrect installation, operation or maintenance.

  • Page 19: Specifications

    Ilumnia Vocalis Specifications SPEAKERS Tweeter: 1 inch soft-dome Woofer: 8 inch LEMS impregnated paper cone Nominal impedance: 8 Ohm Minimum impedance : 6 Ohm Sensitivity 2.83V(1W/1M): 88dB Recommended amplifier power : 20 watt – 250 watt Frequency Response (RAR): 40Hz-25KHz Crossover System: 2-way Dimensions (L x W x H) : 40 x 28 x 48 cm / 15.75 x 11 x 18.90 inch...
  • Page 20 Ilumnia Vocalis This equipment complies with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

Table of Contents