Subscribe to Our Youtube Channel
Summary of Contents for smart-MAIC D103
- Page 1 Measure, Analyze, Improve and Control, ..be smart! USER GUIDE smart-MAIC D103 Version 1.0...
-
Page 2: Table Of Contents
CONTENT Introduction ........3 Purpose of the device and its functions . -
Page 3: Introduction
INTRODUCTION Thank you for purchasing the smart-MAIC 103 Energy Monitor. This device allows you to measure and record changes in electricity consumption and power grid parameters in three phases or three lines in a single-phase network. Purpose of the device and its functions The device is designed for continuous measurement of electrical network parameters and electricity consumption. -
Page 4: Location Of Device Components
The controlled output is intended for switching power loads no more than 50W. Location of device components The device is made in a housing for installation on a DIN rail with an IP20 protection level. When installing at the monitoring object, it is necessary to use a mounting box made of plastic with a level of dust and moisture protection IP54 for indoor installation or IP65 for outdoor installation. -
Page 5: Getting Started
II. GETTING STARTED Installation and connection The device can be installed in an electrical panel on a DIN rail. Follow the steps below to install the device: 1. Mount the device on a DIN rail. 2. Secure the device by sliding the latch up. The connection of the device to the mains must be carried out by trained personnel with a permit of at least group III for electrical safety when working on installations up to 1000 V... -
Page 6: Connection Diagram
III. CONNECTION DIAGRAMS Conditional connection diagram in a 3-phase network Connection diagrams of current transformers and power lines for different device modifications Connecting transformers Transformers 100A and Rogowski rings to Jack 3.5 connectors 1000A / 1500A / 2000A Upper contact group 1 controlled output 2 controlled output 3 current transformer No. - Page 7 7 current transformer No. 3, white wire 8 current transformer No. 3, black wire Smart-MAIC D103 connection in a single-phase network The smart-MAIC D103 energy to consumer monitor is a 3-line device that can be installed in a single-...
- Page 8 IV. MEASURED DATA It is important to understand how the data from the smart-MAIC energy monitor is saved at different time intervals. It is especially important to understand the calculation principle for the Power [W] parameter when it is converted from electrical power into electrical energy.
-
Page 9: Connecting To Your Wireless Network
On your computer or phone, go to the list of wireless networks and select the smart-MAIC0123456789 network connection. If the “smart-MAIC” + network (your device number) is absent, briefly press the Reset button on your device. The default connection password is no. - Page 10 If you are having difficulty finding a device on your network, use the search utility. General tips if you are having problems connecting to WiFi: 1. For stable operation, the signal level must be greater than -80dB, i.e. better than -70dB. 2.
- Page 11 VI. DATA CHECKING Go to the device page in the "Data" section and check the correctness of the readings. When connected correctly, the Power Factor [PF] parameter should tend to 1.00. Also check the logic and correctness of the connection if you see the word Revers. For more information, please check out the articles on our portal.
- Page 12 VII. RESET AND RESTORE FACTORY SETTINGS To restore the factory settings, you must use the Reset button. The Reset button is located near the top group of contacts. The Reset button has two functions: 1. Reboot the device - briefly press the Reset button. After pressing the Reset button, the device will reboot and enter the wireless access point mode.
-
Page 13: Mqtt Service
IX. MQTT SERVICE The device supports data transmission and dry contact output control using the Message Queue Telemetry Transport (MQTT) service. You can activate the MQTT service on the WEB interface of the device in the "MQTT Server" section. If the fields "Username" and "Password" are left blank, then the login to the server will be carried out without authorization. - Page 14 X. TERMS AND NOTICES The function of checking the data for compliance with the specified conditions allows you to automate the operation of a controlled output or receive notifications. - In total, you can configure up to 6 conditions. - Conditions do not have the opposite effect, i.e. if the condition is met and the relay turns on, then the relay will not turn off for the same condition.
- Page 15 To activate the condition, you must select the data type, select the comparison sign ">" or "<", enter the value for comparison, select the required action. Example: If it is necessary to turn off the relay when the voltage exceeds 260V and turn on the relay when the voltage returns to 250V, then two conditions must be enabled: V >...
-
Page 16: Specifications
XI. CONTENTS OF DELIVERY The scope of delivery must comply with the following table № Name Qty. Energy monitor smart-MAIC 103 2 Current transformers XII. SPECIFICATIONS Main characteristics of the device and ranges of measured values Measurement error less than 1% Single phase current measurement up to 100А... - Page 17 www.smart-maic.com...
Need help?
Do you have a question about the D103 and is the answer not in the manual?
Questions and answers