Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for CAM Interiors ErgoVate
- Page 1 2017 User Manual ErgoVate Straight Desk...
-
Page 2: Table Of Contents
Connection …………………………………………………………………………………7 Technical Specifications …………………………………………………………………………8 ErgoVate Introduction …………………………………………………………………………9 ErgoVate Kit Contents …………………………………………………………………9 Installation Instructions ……………………………………………………………….12 Getting Started ……………………………………………………………………….17 4.3.1 Resetting ……………………………………………………………………….17 4.3.2 Operation ……………………………………………………………………….17 Anti-Collision ……………………………………………………………………………….18 Energy Preserving Feature ……………………………………………………….18 Disposal Guidance ……………………………………………………………………….19 Troubleshooting ……………………………………………………………………………….20 ERGOVATE proudly brought to you by... -
Page 3: Preface
ErgoVate is constantly improving its range to meet and exceed customer expectations. This user guide will tell you how to install, use and maintain you ErgoVate product. We are sure this product will provide you with many years of reliable operation. All ErgoVate products undergo rigorous functionality and quality testing prior to shipping. -
Page 4: Important Information
(1) Always make sure all screws are tightened before use of the frame kit, also after a period of use. (2) Duty cycle of the ErgoVate desk is 10% max. 2 minutes operating / min. 18 minutes stop. (3) Maximum load of the ErgoVate desk is 120kg, equally divided. Ensure the loading on each column is less than 80kg. -
Page 5: Safety Instructions
Make sure the correct tools and assembly parts are used when mounting the system. Be aware that the control box can only be connected to the voltage printed on the label. Before moving the frame, remove the plug from main power supply. ERGOVATE proudly brought to you by... -
Page 6: During Operation
(11) Make sure that no persons or items will collide with the table, when adjusting upwards and downwards. (12) If the control box or the columns make any unusual noises or smells, immediately unplug table from power supply. ERGOVATE proudly brought to you by... -
Page 7: Connection
Make sure that all cords are long enough when the frame is in both highest and lowest positions. Control box is normally pre-assembled between the outer pipes, underneath the tabletop. The hand control is normally mounted underneath or within the tabletop in a reachable distance for the user. ERGOVATE proudly brought to you by... -
Page 8: Technical Specifications
(Min. to max.; excluding tabletop) Speed (Depending on the load) 30-40mm/s Desk width 1165-2100mm Noise level 39dB Duty cycle 10; max. 2 min. run / 18 min. stop Ambient temperature 0° ~ 45° C ERGOVATE proudly brought to you by... -
Page 9: Ergovate Introduction
ErgoVate Desk User Manual 4. ErgoVate Introduction 4.1 ErgoVate Kit Contents Top View Side View Assembled View ERGOVATE proudly brought to you by... - Page 10 (including 2 lifting columns and 1 control box) End pipe 2 pcs Foot 2 pcs Control Handset 1 pc Power cord 1 pc Hardware kit Refer to Chart B for more details. 1 set ERGOVATE proudly brought to you by...
- Page 11 ErgoVate Desk User Manual ● Chart B: Hardware kit Description Drawing Qty (pcs) Foot bolt Tabletop screw Control screw Allen key ERGOVATE proudly brought to you by...
-
Page 12: Installation Instructions
Place desk frame on the flat carton. Step 2: Insert end pipes into ends of the desk frame. Step 2.1: Align legs into a vertically upright position. ERGOVATE proudly brought to you by... - Page 13 ErgoVate Desk User Manual Step 3: Fasten the end pipe brackets and lifting columns into place using bolts (8pcs) that were previously embedded into the desk frame. Step 4: Attach feet to the lifting columns using bolts. ERGOVATE proudly brought to you by...
- Page 14 Once the desired frame width has been set, use the supplied Allen key to tighten the set screws (8pcs) total). Note: Set screws are preinstalled into the frame instead of being included within the provided hardware kit. ERGOVATE proudly brought to you by...
- Page 15 Put caps into the holes. Step 6: Plug the power cord and hand control to the control box. Run the wire through the cable management clips. Then, run the hand control wire through the inlet hole. ERGOVATE proudly brought to you by...
- Page 16 Step 8: Flip over the desk and reset control box before adjusting. Simultaneously press and hold the ▲ and ▼ buttons together for 3 to 5 seconds until you hear a beep. ERGOVATE proudly brought to you by...
-
Page 17: Getting Started
(1) Press and hold the ▲ button to raise the desk. (2) Press and hold the ▼ button to lower the desk. Note: For controls with memory functionality, please refer to the Hand Control User Guide. ERGOVATE proudly brought to you by... -
Page 18: Anti-Collision
ErgoVate Desk User Manual 4.4 Anti-Collision The control boxes for the ErgoVate products are programmed with an anti-collision function which may reduce damage to the desk in the event of a collision with a firm object. When the desk is raised / lowered, the power consumption of each column is monitored and compared to a software algorithm. -
Page 19: Disposal Guidance
ErgoVate Desk User Manual 5. Disposal Guidance The ErgoVate desk system may be disposed by dividing components into different waste groups for recycling or combustion. We recommend the system is disassembled as much as possible before disposal. The main groups to sort for waste are: Metal, plastic, cable scrap, combustible material and collection for recoverable resources. -
Page 20: Troubleshooting
If the leg will not move after reset it is defective. Damaged parts must ◆ be exchanged – contact CAM Interiors. ERGOVATE proudly brought to you by...