KamadoSpace Infinite Island - assembly manual version KSI/2021/1.4 TABLE OF CONTENT NOTES BEFORE STARTING TOOLS REQUIRED STEP 1: UNBOX COMPONENTS Package / Base Part / 1 Package / Base Part / 2 Package / Base Part / 4 Package / Base Part / 5...
KamadoSpace Infinite Island - assembly manual version KSI/2021/1.4 NOTES BEFORE STARTING Important - Please read these instructions fully before starting the assembly! ● Make sure you have all the components and tools listed in pages 4-18. ● Remove all the fittings from the flat boxes and separate them into their groups.
KamadoSpace Infinite Island - assembly manual version KSI/2021/1.4 TOOLS REQUIRED Rubber hammer Crosshead screwdriver 8mm allen key 2 x 10mm spanners 4mm allen key...
KamadoSpace Infinite Island - assembly manual version KSI/2021/1.4 STEP 1: UNBOX COMPONENTS Package list: Base Part 1 Base Part 2 Base Part 3 Base Part 4 Base Part 5 Base Part 6 Base Part 7 Base Part 8 Base Part 9...
KamadoSpace Infinite Island - assembly manual version KSI/2021/1.4 STEPS 2-60: ASSEMBLE THE MAIN BODY...
Page 20
KamadoSpace Infinite Island - assembly manual version KSI/2021/1.4 Begin from the bottom of the frame. You will need two bottom bars from package 2, labelled bottom back right (single triangle) and bottom front right (single square), as well as one...
Page 21
KamadoSpace Infinite Island - assembly manual version KSI/2021/1.4 The hook-like clips on the bar should fit into the slots of the panel and the bar should be twisted back to a 90 position. ° Note: Check if the clips fit before assembling.
Page 22
KamadoSpace Infinite Island - assembly manual version KSI/2021/1.4 Now take the other side panel from package 3. Note: The following steps should be performed by two people, for easiest assembly. Align the side panel with the bars at a 45 °...
Page 23
KamadoSpace Infinite Island - assembly manual version KSI/2021/1.4 Twist the panel back to a 90 ° angle, so that it is standing in an upright position. Take the top bars from base part 2 package, and place them in the slots on top of the panels.
Page 24
KamadoSpace Infinite Island - assembly manual version KSI/2021/1.4 Use 4 M6x50 screws and 4 M6 nuts to fasten the top bars to the side panels. Note: Do not tighten the screws too much as you may need to adjust the table later on.
Page 25
KamadoSpace Infinite Island - assembly manual version KSI/2021/1.4 One piece should go from bottom left to top right and the other piece from top left to bottom right. Note: If the pieces do not line up perfectly with the frame, please...
Page 26
KamadoSpace Infinite Island - assembly manual version KSI/2021/1.4 Next step is the installation of one of the inside panels. Start with the panel from package 6. Move it to the inside of the frame at an angle. 3 railings should be facing the...
Page 27
KamadoSpace Infinite Island - assembly manual version KSI/2021/1.4 Align the panel with the screw slots (moving it to the right or left) and fix it with 4 M6x16 screws to the frame. Note: ● If you are unable to screw in...
Page 28
KamadoSpace Infinite Island - assembly manual version KSI/2021/1.4 Now move the panel to an upward position to align with the rest of the frame at a 90° angle. Align the panel with the screw slots (moving it to the right or left).
Page 29
KamadoSpace Infinite Island - assembly manual version KSI/2021/1.4 Turn the current table frame upside down to attach the bottom panels. Note: It is important to rotate the table backwards instead of forward, so that the railings would stay in place and not slide out.
Page 30
KamadoSpace Infinite Island - assembly manual version KSI/2021/1.4 Then attach the bottom panel from package 7. Place the panel on top of the frame and check if all slots align. Then use 12 M4x12 screws to fix it to the frame.
Page 31
KamadoSpace Infinite Island - assembly manual version KSI/2021/1.4 Use a M10x30 screw to attach the caster to the frame in each corner. Insert the caster socket into the wheel.
Page 32
KamadoSpace Infinite Island - assembly manual version KSI/2021/1.4 Place the wheel on the caster and fix it using a M6x40 screw and a M6 nut.
Page 33
KamadoSpace Infinite Island - assembly manual version KSI/2021/1.4 Repeat the same process for all 4 wheels. Note: Once all 4 wheels are attached, engage the brakes. Once the bottom panels and all 4 wheels are securely attached, flip the table once more.
Page 34
KamadoSpace Infinite Island - assembly manual version KSI/2021/1.4 Continue the assembly by attaching the right side panel cover from package 7. Begin attaching the cover from the back corner. Clips on the cover should fit into the slots at the back of the...
Page 35
KamadoSpace Infinite Island - assembly manual version KSI/2021/1.4 Press the cover to the front of the table. Clips at the front should fit into their slots too. Caution: Use caution as the cover might drop down pinching the fingers. Once, the clips fit into all slots,...
Page 36
KamadoSpace Infinite Island - assembly manual version KSI/2021/1.4 Repeat the same steps on the other side. The left side panel cover can be found in package 8. Begin attaching the cover from the back corner. Clips on the cover should fit into the slots at the back of the table.
Page 37
KamadoSpace Infinite Island - assembly manual version KSI/2021/1.4 Once, the clips fit into all slots, press down on the cover from top to bottom, to secure it to the table. The next step is to attach the back panels onto the table.
Page 38
KamadoSpace Infinite Island - assembly manual version KSI/2021/1.4 Similar to side covers, clips on the back panel should fit into their respective slots on the left side of the table (when looking at the back). Caution: Use caution as the cover might drop down pinching the fingers.
Page 39
KamadoSpace Infinite Island - assembly manual version KSI/2021/1.4 Clips on the back panel should fit into their respective slots on the right side of the table (when looking at the back). Caution: Use caution as the cover might drop down pinching the fingers.
KamadoSpace Infinite Island - assembly manual version KSI/2021/1.4 STEPS 61-82: ASSEMBLE GRILL ADJUSTABLE BASE...
Page 41
KamadoSpace Infinite Island - assembly manual version KSI/2021/1.4 To begin assembling the grill base, insert the supporting hooks, from package 1, into their respective slots on the side panel. You can determine which position you need to select for your kamado grill, by checking our website (kamadospace.co.uk/instruction...
Page 42
KamadoSpace Infinite Island - assembly manual version KSI/2021/1.4 Make sure both of the hooks are inserted into the same position slots. Now assemble the grill stand that will hold your kamado. You can find the pieces for it in package 9.
Page 43
KamadoSpace Infinite Island - assembly manual version KSI/2021/1.4 Push down the middle bars to a 90° angle, so that it lays flat on the surface. Take the other sidebar and repeat the process.
Page 44
KamadoSpace Infinite Island - assembly manual version KSI/2021/1.4 This is how it should look when completely assembled. Now insert the grill stand into the table with the wider sidebar facing the front.
Page 45
KamadoSpace Infinite Island - assembly manual version KSI/2021/1.4 Insert the clips on the right of the grill stand into the slots of the middle panel. Note: Make sure the slots are for the same position, as the previously inserted supporting hooks, on the left side panel.
Page 46
KamadoSpace Infinite Island - assembly manual version KSI/2021/1.4 Prepare the ashtray and the lid from package 1. Insert the clips on the ashtray into the slots, at the front of the grill stand at a 45° angle. Push down on the ashtray to fix...
Page 47
KamadoSpace Infinite Island - assembly manual version KSI/2021/1.4 Take the shelf for the grill from package 9. Now lower the shelf onto the grill stand, from the top of the table. Note: The longer lip of the shelf is the...
Page 48
KamadoSpace Infinite Island - assembly manual version KSI/2021/1.4 The shelf should sit on the grill stand on its own. No screws are needed for this step.
KamadoSpace Infinite Island - assembly manual version KSI/2021/1.4 STEPS 83-92: ASSEMBLE WORKTOP AND SPACIOUS DRAWERS...
Page 50
KamadoSpace Infinite Island - assembly manual version KSI/2021/1.4 Pick up the worktop, from package 12. Note: ● We strongly recommend having a partner to assist you out with the placement of the worktop. ● Do not remove the plastic cover from the worktop as it will help prevent scratching the surface of the worktop.
Page 51
KamadoSpace Infinite Island - assembly manual version KSI/2021/1.4 Use 2 M6x50 screws and 2 washers to fix the worktop to the middle of the table frame. Use 2 M6x50 screws and 2 washers to fix the worktop to the right side of the table frame.
Page 52
KamadoSpace Infinite Island - assembly manual version KSI/2021/1.4 Get the 4 accessory drawers from package 10. Align the drawer with the railing system and push it in to the end. Note: ● The green fitting on the side indicates the back of the drawer.
Page 53
KamadoSpace Infinite Island - assembly manual version KSI/2021/1.4 Repeat the process for the remaining 3 accessory drawers.
KamadoSpace Infinite Island - assembly manual version KSI/2021/1.4 STEPS 93-109: ASSEMBLE MIDDLE DRAWERS...
Page 55
KamadoSpace Infinite Island - assembly manual version KSI/2021/1.4 Begin assembling the middle drawers. You can find the metal parts in package 9. Take the two side panels and fit them into the slots on the bottom panel. Note: ● The bends on the side panels should be facing outwards.
Page 56
KamadoSpace Infinite Island - assembly manual version KSI/2021/1.4 The side panels should align perfectly with the front of the bottom panel. Take the back panel piece and fit it into the slots on the side panels. Note: The bend on the back panel should be facing outwards.
Page 57
KamadoSpace Infinite Island - assembly manual version KSI/2021/1.4 Use 3 M4x6 screws to fix the back panel to the bottom. Attach the metal construction of the drawer to an HPL panel from package 13. Note: ● We recommend to lay down...
Page 58
KamadoSpace Infinite Island - assembly manual version KSI/2021/1.4 Take two orange adjustable fittings from package 1. Make sure you have them ready and set on position 0. Fittings will go on the bottom of the drawer, and the orange part should be facing the middle of the drawer.
Page 59
KamadoSpace Infinite Island - assembly manual version KSI/2021/1.4 You can now put the assembled drawers onto the soft close railing system. Pull out the railings and put the drawer on top of them. Pull the railings to the front of the drawer until they fix into place.
Page 60
KamadoSpace Infinite Island - assembly manual version KSI/2021/1.4 The drawer will fit onto the system, when the spikes on the railing go through the holes at the back of the drawer. Note: The smaller picture on the left shows how to adjust the shelf...
KamadoSpace Infinite Island - assembly manual version KSI/2021/1.4 STEPS 110-143: ASSEMBLE CHARCOAL DRAWER...
Page 62
KamadoSpace Infinite Island - assembly manual version KSI/2021/1.4 Begin assembling the charcoal drawer. You can find the metal parts in package 9. Take the two side panels and fit them into the slots on the bottom panel. Note: The bends on the side panels should be facing outwards.
Page 63
KamadoSpace Infinite Island - assembly manual version KSI/2021/1.4 Note: You can put a piece of thicker cardboard or a screwdriver under the back of the bottom panel for the clips to slide in easier. Take the two long metal bars...
Page 64
KamadoSpace Infinite Island - assembly manual version KSI/2021/1.4 Lift the small piece up to a 90° angle. Attach the left bar to the small piece at a 45° angle.
Page 65
KamadoSpace Infinite Island - assembly manual version KSI/2021/1.4 Straighten the left bar to a 90° angle. It should look like a letter H. Attach the H bar to the back of the drawer at a 45° angle.
Page 66
KamadoSpace Infinite Island - assembly manual version KSI/2021/1.4 Twist the H bar to the front of the drawer to a 90° angle. It should now be in place and standing upright. Take the back panel piece and fit it into the slots on the side panels.
Page 67
KamadoSpace Infinite Island - assembly manual version KSI/2021/1.4 Push the back panel down to attach it to the side panels. Note: If you are having trouble aligning the back panel with the side panels, you can take a rubber hammer, and lightly tap on the top to align it properly.
Page 68
KamadoSpace Infinite Island - assembly manual version KSI/2021/1.4 Use 7 self-tapping screws to fix the metal construction to the HPL panel. Continue by attaching the supporting pieces from package Lower the pieces inside of the drawer at a 45° angle.
Page 69
KamadoSpace Infinite Island - assembly manual version KSI/2021/1.4 Insert the clips into the slots on the H bar and lift the supporting pieces up to a 90° angle. The front side of the supporting pieces should align with the screw holes on the HPL panel.
Page 70
KamadoSpace Infinite Island - assembly manual version KSI/2021/1.4 Use 6 self-tapping screws to attach it to the HPL panel. Take two orange adjustable fittings from package 1. Make sure you have them ready and set on position 0. Fittings will go on the bottom of...
Page 71
KamadoSpace Infinite Island - assembly manual version KSI/2021/1.4 The final version of the fully assembled charcoal drawer should look like this. You can now put the assembled charcoal drawer onto the soft close railing system. Pull out the railings and put the...
Page 72
KamadoSpace Infinite Island - assembly manual version KSI/2021/1.4 Pull the railings to the front of the drawer until they fix into place. The charcoal drawer will fit onto the system, when the spikes on the railing go through the holes at the back of the drawer.
KamadoSpace Infinite Island - assembly manual version KSI/2021/1.4 STEPS 144-154: ASSEMBLE SLIDING FRONT...
Page 74
KamadoSpace Infinite Island - assembly manual version KSI/2021/1.4 To assemble the sliding front you will need an HPL cover from package 13 and two metal fittings from package 9. Note: Keep the surfaces on which you lay HPL panels clean and free of other objects as they may scratch them.
Page 75
KamadoSpace Infinite Island - assembly manual version KSI/2021/1.4 You are now ready to attach the sliding front to the table. Begin with the bottom side of the panel. Insert the bottom metal runners through the gap in the middle.
Page 76
KamadoSpace Infinite Island - assembly manual version KSI/2021/1.4 Then slowly lower the panel to the bottom. Note: Do not let go or drop the panel as it may damage the metal runners. Now insert the top metal runners into the same gap in the middle.
Page 77
KamadoSpace Infinite Island - assembly manual version KSI/2021/1.4 You should now be able to move the sliding front up and down. Note: Be careful not to drop the panel as it may damage the metal runners.
KamadoSpace Infinite Island - assembly manual version KSI/2021/1.4 STEPS 155-163: ASSEMBLE REMOVABLE ACCESSORIES...
Page 79
KamadoSpace Infinite Island - assembly manual version KSI/2021/1.4 You can find the herb shelf in package 11. As no additional assembly is required, all you need to do is to insert the shelf into one of the slot pairs on the side panels.
Page 80
KamadoSpace Infinite Island - assembly manual version KSI/2021/1.4 The paper towel rack, the hook rack and the hooks can all be found in package 1. Repeat the same process as with the herb shelf. Note: You can put the racks on any...
Page 81
KamadoSpace Infinite Island - assembly manual version KSI/2021/1.4 CONGRATULATIONS! Please don’t forget to register your KamadoSpace Island on our website, to validate the warranty (https://kamadospace.co.uk).