RACK IT PRO 01904 Assembly Instructions

RACK
YOUR HEADACHE-FREE GUIDE TO RACK IT LIKE A BOSS
You've got this. We know because you take pride in your passions. Take care of your stuff. That's why you purchased this Rack It PRO
4 Drawer Cabinet. You're particular. And we like that. Because we know you'll take the time to check off all the Parts listed below and
to read through these Assembly Instructions before you start. Cue Farnsey (or Beyoncé – whatever lifts you).
CABINET PARTS:
A
PART A - BOTTOM PANEL x 1
PART S - M6 SCREW x 44
(40 for cabinet assembly (for assembly of locking bar,
+ 4 for joining 2 Cabinets) Note: 4 x M5 screws are pre-fixed to Cabinet panels)
DRAWER PARTS:
J
PART J - DRAWER
BOTTOM PANEL x 4
PART U - M4 SCREW x 76
(FOR DRAWER ASSEMBLY)
PLEASE NOTE: If using an electric screwdriver only loosely tighten screws, finish tightening with hand screwdriver to avoid damage.
STEP 1
Your Cabinet starts here.
With Bottom Panel (A).
Like the foundations of a house.
So when you're fixing on Side Panels (B & C),
think: do I want to rush the foundations?
The answer is, of course, no way.
Hot tips:
1. Make sure the pre-punched screw holes on Bottom Panel (A) are to the back.
2. Make sure the narrowest gap between the boxy ridges on the interior and the front
edge of each Side Panel is to the front.
3. Make sure the square fixing points for the Drawer Runners line up. You'll thank us later.
4. Your Right Side Panel (Part C) is the one with the row of pre-fixed bolts down the front
inside channel
STEP 3
You've only just started and it's already time to attach your roof.
As you screw it in place be sure to check the hole for your lock is at
the FRONT of the Cabinet. It can be dark inside your box/cave, so
if you need to, use a torch!
You've boxed It. Cue roof shout!
And let's move onto Stage 2...
MADE IN CHINA | DISTRIBUTED BY:
Zenexus (AUS) Ph. 1300 734 714 Zenexus (NZ) Ph. 0800 443 058
4 DRAWER CABINET
IT
ASSEMBLY INSTRUCTIONS
ITEM CODE: 01904
B
PART V - M5 NUT x 6
(for assembly of
locking mechanism)
PART B -
LEFT SIDE PANEL x 1
PART T - M5 SCREW x 2
P
PART P - SMALL DRAWER
RIGHT SIDE x 2
O
PART O - SMALL DRAWER
LEFT SIDE x 2
Back
B
A
C
PART C -
RIGHT SIDE PANEL x 1
PART G - LOCKING SIDE BAR X 1
R
PART R - SMALL DRAWER
FRONT x 2
Q
PART Q - SMALL DRAWER
BACK x 2
STAGE 1: BOX IT
STEP 2
Grab your 2x Back Panels (D1 & D2).
C
Fix the bottom of D1 to your Bottom Panel (A).
Once D1's screwed in place,
you can fix its buddy D2 on top.
Front
Hot tip:
It's easy to tell D1's bottom from its top because it has 5x M6 Nuts
pre-fitted along its Bottom Lip.
Hole to fit
the Lock on
the Front
AUSTRALIA: RACK-IT.COM.AU
TOOLS REQUIRED: WRENCH &
SCREWDRIVER (NOT INCLUDED)
WARNING: HANDLE CUT METAL
EDGES CAREFULLY
When assembling or installing this product
wear protective gloves and eyewear
D1
PART D1 - BACK PANEL x 1
D2
PART D2 - BACK PANEL x 1
PART F - LOCKING TOP BAR X 1
L
PART L - LARGE DRAWER
RIGHT SIDE x 2
K
PART K - LARGE DRAWER
LEFT SIDE x 2
+
E
NEW ZEALAND: RACK-IT.CO.NZ
SAFETY TIP
E
PART E - TOP PANEL x 1
PART H - DRAWER RUNNERS x 12
PART I - DOOR LOCK, TONGUE & KEYS
N
PART N - LARGE DRAWER
FRONT PANEL x 2
M
PART M - LARGE DRAWER
BACK PANEL x 2
D2
D1