Do you have a question about the TNS-0163 and is the answer not in the manual?
Questions and answers
Summary of Contents for Fomis TNS-0163
Page 1
说明书 Instructions 产品名称:Switch 蓝牙手柄 Product name: Switch Bluetooth Controller 产品编号:TNS-0163 版本:A1.1 Product No.: TNS-0163 Rev.: A1.1 1、产品简介: 1.Production Introduction: 支持蓝牙跟 Switch 主机连接;有功能键连发设定-Turbo 功能键、截屏键、陀螺仪重力感应、振 动、NFC 感应、手柄唤醒主机等功能; It supports the connection between the Bluetooth and Switch console, and it is designed with continuous firing settings in functions keys (Turbo function keys), screen shot key, gyroscope gravity induction, vibration, NFC induction and console wake-up with controller, etc.
Page 2
3.2、设计有 Turbo 设置功能、可改变 Turbo 速率,有截屏键、陀螺仪重力感应等功能。 3.2 It is designed with Turbo setting function, variable Turbo rate, screen shot key and gyroscope gravity induction and other functions. 3.3、具有双振子振动功能。 3.3 It is designed with vibration function of double vibrators. 3.4、支持 NFC 感应。 3.4 Support NFC sensing.
Page 3
L3 键(左 3D 摇杆下压按键功能) 有 L3 key (left 3D joystick press function) R3 键(右 3D 摇杆下压按键功能) 有 R3 key (right 3D joystick press function) 充电指示灯 有 Charging lamps 振动功能 有 Vibration function NFC 读取功能 支持 NFC reading function Support 手柄升级 支持...
Page 4
console paired previously; if the back connection is not successful within 8 seconds, it will enter into the auto sleep status. ③ 在主机和手柄休眠时,按 HOME 键可唤醒主机,如果没有唤醒成功,可再次按下 HOME 按键唤醒主机和 手柄。 ③ Press the HOME key to wake up the console when the console and controller are in dormant state; if not successful, you can press the HOME key again to wake up the console and controller.
Page 5
9 Low Battery Warming: 9.1、电池低电量报警:当前连接通道 LED 指示灯快速闪烁。 9.1 Low battery warming: The LED lamp of the current connection channel flashes quickly. 备注:当主机提示低电时手柄 LED 指示灯也会快速闪烁几下,不会一直持续闪烁 Remarks: When the host indicates low power, LED lamp of the controller will flash a few times quickly instead of continuous flashing.
Page 6
Press and hold the Turbo key, pull the 3d upward; Turbo speed: 5Hz->12Hz->20Hz change 按下 Turbo 按键不放,把 3d 往下拨,Turbo 速度:20Hz->12Hz->5Hz 变化 Press and hold the Turbo key, pull the 3D downward; Turbo speed: 20Hz->12Hz->5Hz change 备注:上电默认 turbo 速度为 20Hz Note: The default turbo speed is 20Hz after power-on. 10.7、手柄休眠清除所有按键...
Page 7
14.2、本产品在使用时如 3D 摇杆有漂移现象时,请重新连接手柄,也可在主机上进行手动校验 后再使用,注意重连手柄时,不要碰到 3D 摇杆。 14.2 If the 3D joystick drifts in use, please reconnect the controller; you can also carry out manual calibration on the console before use; do not touch the 3D joystick when reconnecting the controller. 15、环境条件:...
Page 8
17.3 This product should be used or stored by avoiding dusts and heavy loads to guarantee its service life. 17.4、本产品因使用不当而造成浸水、撞坏或摔坏,出现电气性能问题,请停止使用。 9.4 Do not use the product which is soaked, crashed or broken or with electrical performance problems caused by improper use. 17.5、不要用微波炉等外部加热设备对其进行干燥处理。...
Page 9
FCC Caution: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Need help?
Do you have a question about the TNS-0163 and is the answer not in the manual?
Questions and answers