Advertisement
Quick Links
Troubleshooting
Troubles
Possible Causes
- Water full indicator lamp blinks, and water
1. UNIT DOES NOT START
tank is full
WHEN PRESSING POWER
- Room temperature is higher than the setting
temperature. (Electric heating mode)
BUTTON
- Room temperature is lower than the setting
temperature. (Cooling mode)
- The doors or windows are not closed.
- There are heat sources inside the room.
- Exhaust air hose is not connected or
2. Not cool enough
blocked.
- Temperature setting is too high.
- Air inlet is blocked.
3. Auto Power-Off in
- Heating protection, when the temperature at
the air outlet exceeds 70°C, the unit will
heating mode
power off automatically.
- The ground is not level or not flat enough.
4. Noisy
- The sound comes from the flowing of the
refrigerant inside the air conditioner.
Room temperature sensor failed
5. E1 Code
6. E2 Code
Evaporator coil sensor failed
6. E3 Code
Water tank full
Note: The real products may look different.
Suggested Remedies
Dump the water out of the
water tank.
Reset the temperature
Reset the temperature
Make sure all the windows and
doors are closed.
Remove the heat sources if
possible
Connect or clean the exhaust
air hose.
Reset the temperature
Clean the air inlet.
Restart the unit at enough lower
room temperature.
Place the unit on a flat, level
ground if possible
It is normal.
Replace room temperature
sensor (the unit can also work
without replacement.)
Replace evaporator coil sensor.
Please empty the water tank.
26
Portable Air Conditioner
User's Manual
Article No.：PA010998 / PA010997
Please read this user's manual carefully to ensure proper use, maintenance and installation
Advertisement
Summary of Contents for OZONA PA010998
- Page 1 6. E2 Code Evaporator coil sensor failed Please empty the water tank. 6. E3 Code Water tank full Note: The real products may look different. Article No.：PA010998 / PA010997 Please read this user’s manual carefully to ensure proper use, maintenance and installation...
-
Page 2: Table Of Contents
Safety Awareness Contents VERY IMPORTANT! Please do not install or use your mobile air conditioner before you have Safety Awareness -------------------------------------------------------------------- 1 carefully read this manual. Please keep this instruction manual for an eventual product warranty and for future reference. Name of Parts ------------------------------------------------------------------------ 15 Accessories --------------------------------------------------------------------------- 16 WARNING... - Page 3 • The appliance must be stored in such a way as to prevent mechanical failure. 11. If the supply cord is damaged, it must be replaced by the manufacturer, its • Individuals who operate or work on the refrigerant circuit must have the service agent or similarly qualified persons in order to avoid a hazard.
- Page 4 22. Servicing shall only be performed as recommended by the equipment 1.3 General work area manufacturer . Maintenance and repair requiring the assistance of other skilled All maintenance staff and others working in the local area shall be instructed on personnel shall be carried out under the supervision of the person competent in the nature of work being carried out.
- Page 5 1.8 Checks to the refrigeration equipment sealed covers, etc. If it is absolutely necessary to have an electrical supply to Where electrical components are being changed, they shall be fit for the equipment during servicing, then a permanently operating form of leak detec- purpose and to the correct specification.
- Page 6 5 DETECTION OF FLAMMABLE REFRIGERANTS shall not be used for this task. Flushing shall be achieved by breaking the vacuum in the system with OFN and continuing to fill until the working pressure Under no circumstances shall potential sources of ignition be used in the is achieved, then venting to atmosphere, and finally pulling down to a vacuum.
- Page 7 a) Become familiar with the equipment and its operation. appropriate refrigerant recovery cylinders are employed. Ensure that the b) Isolate system electrically. correct number of cylinders for holding the total system charge are available.All c) Before attempting the procedure ensure that :mechanical handling equipment cylinders to be used are designated for the recovered refrigerant and labelled is available, if required, for handling refrigerant cylinders;...
- Page 8 The achieved competence should be documented by a certificate. equipped for servicing units with flammable refrigerants. • Ensure sufficient ventilation at the repair place. Training • Be aware that malfunction of the equipment may be caused by refrigerant loss The training should include the substance of the following: and a refrigerant leak is possible.
-
Page 9: Name Of Parts
• Ensure sufficient ventilation at the equipment location. local regulations and give the minimum requirements for the provision of safety • Be aware that malfunction of the equipment may be caused by refrigerant loss and/or health signs for a work location. and a refrigerant leak is possible. -
Page 10: Accessories
Accessories Appearance and Function of Control Panel Fig 4 Fig 2 SPEED Press this button to select wind speed. You can choose low wind speed, medium wind speed or high wind speed. Appearance and Function of Remote Controller Note: in dehumidification and sleep mode, the wind speed cannot be adjust- ed. - Page 11 TIMER TEMP- You can set the timer on/off. Under cooling and heating function, set in the range of 16 ~ 31 °C tempera- ture.Every click on the temperature, set temperature reduced by 1 °C. Timing start up: after setting timing start up, the machine will automatically start up and run when the timing time arrives.
- Page 12 wind speeds. Operation Introduction Heating operation（optional） 1. Keep pressing the mode key until the heating light is on. Before starting operations in this section: 2. Press the "+" or "-" key to choose their own need to temperature, temperature 1) Find a place where there is power supply nearby. range of 16-31 °C / 61 ~ 88 °F.
-
Page 13: Installation Explanations
- When using functions on cooling and dehumidifying, keep an interval of at least 3 minutes between each POWER. - Power supply meets the requirements. - The socket is for AC use. - Do not share one socket with other appliances. - Power supply is AC220V，50Hz 2. -
Page 14: Maintenance Explanations
Maintenance Explanations Declaration: 1) Before cleaning, be sure to disconnect the unit from any electric supply outlet; 2) Do not use gasoline or other chemicals to clean the unit; 3) Do not wash the unit directly; 4) If the conditioner is damaged, please contact the dealer or repair shop. Fig 8 4.
Need help?
Do you have a question about the PA010998 and is the answer not in the manual?
Questions and answers