Page 2
Dear Nüve User, We would like to take this opportunity to thank you for preferring this Nüve product. Please read the operating instructions carefully and keep them handy for future reference. Please detain the packing material until you see that the unit is in good condition and it is operating properly.
Page 3
WARRANTY CERTIFICATE 1. Nüve warrants that the equipment delivered is free from defects in material and workmanship. This warranty is given for a period of two years. The warranty period begins from the delivery date. 2. Warranty does not apply to parts normally consumed during operation or general maintenance or any adjustments described in the operating instructions provided with the instrument.
INTRODUCTION 1.1. USE AND FUNCTION DF series Ultra Low Temperature Freezer is designed for the storage of the samples needed to store at ultra-low temperature and it is used in the hospitals, blood banks, epidemic diseases research centers, research laboratories in the universities, genetic engineering and bio- pharmaceutical industry.
DF Series Freezers are designed and manufactured in accordance with national and international directives, EN 50419 and EN 61000-6-3 standards under the supervision of total quality management systems ISO 9001 and ISO 13485. This device is in compliance with WEEE Regulation. If the warnings mentioned in this manual are not considered, NUVE will not be responsible from their results.
SYMBOLS AND LABELS Symbol in the operating instructions: Attention, general hazard area. This symbol refers to safety relevant warnings and indicates possibly dangerous situations. The non-adherence to these warnings can lead to material damage and injury to personal. Symbol in the operating instructions: This symbol refers to important circumstances.
INSTALLATION ENVIRONMENTAL CONDITIONS The instrument is designed to operate safely under the following conditions: Indoor use only Ambient temperature: 5°C to 30°C Maximum relative humidity for temperature up to 31°C: 80 % Maximum altitude: 2000 m ...
HANDLING AND TRANSPORTATION All handling and transportation must be carried out by using proper equipment and experienced staff. The instrument must be supported underneath, moved in vertical position and never be turned upside down. UNPACKING Remove the cardboard box packing and ensure that no damage has occurred during transportation.
GENERAL PRESENTATION DOOR HANDLE CONTROL PANEL CHART RECORDER CONDENSER (OPTIONAL) FILTER Figure 1 CO2 BACK-UP USB PORT-1 OUTPUT POWER LED USB PORT-2 FUSES ETHERNET POWER CORD RS 232 POWER KEY NC-CONTACT OUTPUT REMOTE ALARM OUTPUT Figure 2...
5.6.1. CHAMBER DIMENSIONS DF 290 * DF 490 DF 590 575 mm 610 mm 715 mm 310 mm 310 mm 310 mm 310 mm 310 mm 310 mm 310 mm 310 mm 310 mm 310 mm 310 mm 1070 mm 965 mm 1120 mm 420 mm...
Page 13
This symbol denotes the graph screen. The last 24 hours of operation of the device can be monitored on the graph of the temperature vs. time by pushing the button corresponding to this symbol. It is recorded every 10 minutes. This symbol denotes the alarm range settings.
PRIOR TO OPERATION Plug-in the instrument to correctly grounded sockets. Insert the key to the power switch lock at the back. Power the freezer on by rotating the key clockwise. Observe that the microprocessor control system is activated. ...
Password screen will appear when the MENU button (F1) is pushed. You can enter the password by using the value increase (F1) and decrease keys (F2). The password is user’s password and can be changed on settings page (See section 6.1.2.). The password is 0000 for the first usage.
Page 16
“Select Language” submenu is selected on the settings page by using the value increase (F1) and decrease (F2) keys. The page on the left appears when enter key (F4) is pushed. The language of the control panel can be set as Turkish, English, French, Russian or Spanish.
6.1.3. MEMORY “Memory” submenu is selected on the menu page by the value increase (F1) and decrease (F2) keys. The page on the left appears when enter key (F4) is pushed. INTERNAL MEMORY “Failure History” submenu is selected on the memory page by the value increase (F1) and decrease (F2) keys.
When the temperature sensor is broken, “–“appears in the temperature column since temperature cannot be read by the sensor. “History (GRAPH)” submenu is selected on the memory page by the value increase (F1) and decrease (F2) keys. “Select Record Date” page appears when enter key (F4) is pushed. Enter a date to analyze corresponding operation and then push the enter key (F4).
Copy Failure History: As USB stick is connected to the device, all error history in the internal memory is transferred to USB stick when “Copy Failure History” is selected. When loading is finished completely, push the enter key (F4) to exit from this page. 6.1.4.
Tab key (F3) is used for changeover from one digit of phone number to another. After all phone numbers from “Phone 1” to “Service 2” is entered as mentioned above, push the enter key (F4) and return to main page. 6.1.5.
“Login” is selected on the e-mail page by the value increase (F1) and decrease (F2) keys. The page on the left appears when enter key (F4) is pushed. Each character of e-mail addresses is written one by one. The first character is entered by pushing value increase (F1) and decrease keys (F2) and tab key (F3) is pushed to enter the next character.
When the temperature alarm setting key (F4) is pushed in the operation mode, the “Alarm Range” page shown on the left appears. The desired alarm value can be adjusted by pushing value increase (F1) and decrease (F2) keys. Enter key (F4) is pushed to save the value and returned to the working screen.
DISPOSAL MANAGEMENT CONCEPT The currently valid local regulations governing disposal must be observed. It is in the responsibility of the user to arrange proper disposal of the individual components. All parts which may comprise potentially infectious materials have to be disinfected by suitable validated procedures (autoclaving, chemical treatment) prior to disposal.
A list consisting of the codes of errors can be accessed from the memory page (See section 6.1.3.1). ‘EoFF’, ‘Err3’, ‘Err4’, ‘Err5’ and ‘Err6’ do not appear on working screen and they are only shown in the list of the error history. If an error occurs, please contact to an authorized NÜVE agent to seek technical help.
SIM card which will be used for GSM module should not have PIN code. Plug-in the GSM module to correctly grounded sockets. Connect the end of RS 232 cable of GSM module (See Figure 6) to the RS 232 port on the ultra-low freezer (See Figure 2).
CHART RECORDER The below mentioned are provided with the chart recorder, please check them; 100 ea. circular diagram paper for chart recorder 1 ea. pen for chart recorder 1 ea. battery 2 ea. circular recorder keys. Chart recorder measures the temperature in the chamber and records this value by using a pen.