Advertisement
Table of Contents
- 1 Table of Contents
- 2 1: Features & Warnings
- 3 2: Connections & Installations
- 4 3: Operating Instructions
- 5 4: Mixing & Kneading
- 6 5: Cleaning
- 7 6: Maintenance
- 8 7: Specifications
- 9 8: Parts Diagram
- 10 9: Parts List
- 11 10: Troubleshooting
- 12 11: Warranty
- 13 12: Service
- 14 13: Declaration of Conformity
- Download this manual
Advertisement
Table of Contents
Summary of Contents for Famag IM-5S
- Page 1 Famag User Manual Professional Spiral Dough Mixers Models IM-5/8/10...
-
Page 3: Table Of Contents
Table of Contents 1: Features & Warnings Pg. 3 8: Parts Diagram Pg. 8 2: Connections & Installations Pg. 3 9: Parts List Pg. 9 3: Operating Instructions Pg. 4 10: Troubleshooting Pg. 10 4: Mixing & Kneading Pg. 5 11: Warranty Pg. -
Page 4: 3: Operating Instructions
Start/Stop Switches: There are two buttons on your Famag mixer for controlling the direction of both the dough hook and bowl. The left arrow button moves the spiral hook in a downward motion, and the right arrow button moves the hook in an upward motion. -
Page 5: 4: Mixing & Kneading
To start the mixer, be sure the head set-screws are tightened and the bowl guard is lowered, then press either arrow-button to start the mixer. To stop, press the red button. Speed Control: The rotary switch located beside the start/stop switches controls speed. 4.0 Mixing and Kneading Suggestions First, make sure there are only food ingredients in the bowl and no foreign objects that could cause damage to the machine. -
Page 6: 6: Maintenance
We recommend viewing all of the videos in the Library in your first week of Famag ownership. They’re packed with information that will maximize your Famag experience and keep your mixer humming along in peak form for many years! -
Page 7: 7: Specifications
1. The bowl and dough hook rotate at a ratio of 1:10 on regular speed models, and at a ration of 1:12-13 on high hydration (HH) models. For a breakdown of the RPM of the bowl and hook at each speed, visit: 4phg.com/famag-mixer-rpm. FAMAG DOUGH CAPACITIES AT 60% HYDRATION Flour... -
Page 8: 8: Parts Diagram
8.0 Parts Diagram... -
Page 9: 9: Parts List
9.0 Parts List Part 8mm Set Screw for Large Pulley Frame Pulley, Large Main Switch (Reversing) Outer Assembly Drive Belt, Bowl Bowl Bumper Disk Drive Shaft Speed Controller Bottom Drive Shaft Bearing Support Control Board 6mm Set Screw for Small Pulley 8x25mm Flanged Socket Head Undercarriage Bolt Pulley, Small Speed Control Knob Assembly... -
Page 10: 10: Troubleshooting
See video #08 in the PHG Famag Use Video Library. ▪ Famag mixers run exceptionally quiet overall, so it’s normal to hear the chain running and other sounds that ▪ would be drowned out by loud motor or gear noise in other mixers. - Page 11 C: The microswitch must be functioning correctly electrically, so that it actually completes its circuit when it ▪ clicks. D: For important info about the bowl guard safety switch, see video #03 the online Famag Use Video ▪ Library. (10.3.3) Defective Control Board: If power is supplied to the mixer and you have determined that neither the bowl •...
- Page 12 Europe as well, but specific construction standards differ in some ways, and incompatibility may exist between a home’s GFCIs and the Famag mixer’s VFD (Variable Frequency Drive) circuitry. Experience has shown that if your GFCIs trip with one Famag mixer, the same thing would happen with any other Famag mixer, as well.
- Page 13 • whether your mixer has three buttons (forward, on/off, and reverse) or only two buttons (on and off). B: See video #14 in the PHG Famag Use Video Library. • 10.11 PROBLEM: The rubber ring around the bowl locking disk is not staying on around part of the ring and/or is separated where its ends were originally joined (10.11.1) The rubber ring has a “U”...
-
Page 14: 11: Warranty
Use firm void fill sheets that will reliably prevent that side of the mixer from ever contacting the box wall. Owners are strongly encouraged to retain the Famag mixer carton and all internal void fill materials, in case you need to... -
Page 15: 13: Declaration Of Conformity
13.0 Certificate of Conformity... - Page 16 FA.MAG. S.r.l. Via Pioppi, C.da Brugazza, 25 98041 Monforte Giorgio - Fraz. Marina ITALY P.I. 02618120832 (ME) LITOFAST - Venetico (ME)
Need help?
Do you have a question about the IM-5S and is the answer not in the manual?
Questions and answers
My famag im-8s just stopped mid mixing
A Famag IM-5S mixer could stop mid-mixing due to several possible reasons:
1. Defective Control Board – If power is supplied and neither the bowl sensor nor the bowl guard safety switch is the issue, the control board may be faulty and require replacement.
2. Bowl Guard Safety Switch Issue – If the switch does not engage properly, it may disrupt power to the mixer.
3. GFCI Tripping – Some home GFCI outlets may be incompatible with the mixer's Variable Frequency Drive (VFD) circuitry, causing power interruptions.
Before inspecting or troubleshooting, ensure the mixer is disconnected from power.
This answer is automatically generated