Advertisement
Quick Links
Our vision:
To be the world leader in prevention systems to prevent
water damage in residential, industrial and commercial
areas.
Our mission:
To provide a product assuring peace of mind and protection
of the environment through our system, by controlling
serious incidents caused by water in all sectors.
Our product:
The aim of our product is to prevent damage caused by
water. The product is an electronic valve installed at the
main water entrance that automatically shuts off when the
control panel receives an RF signal from a wireless water
sensor placed in a strategic location. This product is
extremely effective in preventing water overflow caused by
the hot water tanks, bathtubs, sinks, toilets, dishwashers,
washing machines, etc. All you do is place the wireless
sensors anywhere you foresee as a potential trouble spot.
Sensors
Sensors are installed in strategic locations throughout your house, such as at water heaters,
dishwashers, washing machines, toilets, bathtubs, ready to send
immediate signals in case of water leak. Sensors are also equipped
with cable detection
•
The control panel is the Main Unit Interface that
is in constant communication with the sensor and the
electronic valve. The entire System is Certified CSA and
UL
A reliable solution against
water damages
Control panel
The control panel interacts with sensors for water leak
detection and battery strength. It also monitors ambient
temperature and proper valve connection.
Smart valve
A smart valve is installed at
the main water inlet and will
automatically shut off water
supply if sensors detect a leak.
Remote control
Insurance companies
recommend that you
shut off the main water
supply of your property during
extended absences. The Water
Protec remote control allows you
to control the intelligent valve
from a distance.
Advertisement
Summary of Contents for Water Protec LED 13
- Page 1 A reliable solution against water damages Smart valve A smart valve is installed at Our vision: the main water inlet and will automatically shut off water To be the world leader in prevention systems to prevent water damage in residential, industrial and commercial supply if sensors detect a leak.
- Page 2 Advantages of the Water Protec system Water-Protec makes sure the • Electronic stainless steel valve guaranteed 5 years with system is functional the certification even in a situation (CSA 125.3 vs a plastic valve on many competitors) of power failure •...
- Page 3 Owner’s Manual Thank you for purchasing a Water-Protec product. We want to offer you the best product that protects you against water damage and give you peace of mind. We therefore invite you to read this guide carefully, which is designed to suit your needs. Useful information at your fingertips. A fully autonomous, automated and connected solution against water damage.
- Page 4 Warranty Water-Protec products have been manufactured under the highest standards of quality of the industry. That’s why Water-Protec offers a 5 year warranty on the valve, a 2 year warranty on parts and a 1 year warranty on the installation if performed by one of our Certified Network member starting on the original date of purchase.
- Page 5 Installation We recommend that the installation of the valve should be performed by a Follow the link to make the installation easier: certified plumber youtu.be/kOtS3V0M4w8 Getting ready Tools Here is the list of tools you will need : First, check the content of the box: make sure all parts are present and Snap-off For plumbing: that you have enough sensors for your property configuration.
- Page 6 Synchronizing and functioning (continued) Synchronizing the sensors Once all the sensors and the remote control are synchronized placed, and the valve installed. The green LEDs on the control panel should show for each sensor installed. Sensors can be tested by shorting the electrodes as described above. After a short delay an alarm will be heard from the control panel, and the activated sensor’s LED should turn red.
- Page 7 Valve Installation (continued) Measure the length of the pipe to be cut and cut the pipe. Apply Teflon tape to the end caps and securely thread the end caps into the valve using an adjustable wrench. Insert the valve into the piping and seal securely with a pex conduit clamp.
- Page 8 Wi-Fi network. Press the buttons simultaneously for at least 10 seconds. When the 20 position indicator light flashes, release both buttons and press Cancel. LED 13 LED 14 LED 15 Access point server begin Access point web site activated...
- Page 9 Communication with the control panel The water sensors as well assending an alarm signal if the electrodes are immersed in water, also periodically send a signal (IOK) to the control panel, indicating that they are present and functional. if this signal is not received on schedule by the control panel, an alarm is triggered.
- Page 10 Additional information Replacing the remote control In the case of loss or failure, to replace a remote control that has already been synchronized with a control panel,take the following Program steps: First, push the button on the control panel to activate Program mode. The control panel is in Program Mode when Reset the first LED is flashing.
- Page 11 IOK Signal Loss When water sensors are present and working, they send an IOK (I’m OK) signal 6 times a day (every 4 hours). In view of the fact that these signals are brief so as to conserve battery power, sometimes they may not be received due to interference or signal overlaps. If three consecutive signals are missed, after 12 hours the relevant LED flashes green.
- Page 12 You can photocopy the inventory sheet below and place it near the control panel. This will also allow you to use it again in case you add twin sensors for example. Inventory Sheet List of strategic location to protect Kitchen sink, dishwasher, refrigerator connected to water, central air conditioning, water heater tank, toilets, bathroom sinks (2 sensors if double sink), bidet, shower, bath, garage sink,etc.
- Page 13 Special situations and reminder Sensors If your sensor has been in contact with water, you should change its batteries. The system takes its battery readings at 12-hour intervals. If your sensor has water inside its casing, we recommend that you replace the sensor with a new one. Reminder : Water-Protec recommends that you change your batteries every 12 months so that you do not experience low battery levels that will impair system operation.
- Page 14 Thank you! We would like to thank you once again to buy Water-Protec Product. Water-Protec is a Canadian company and its distribution network is present in all Canadian provinces. We help prevent water damage through a technological innovation designed and produced in Canada at our own production facilities.
- Page 15 Answers to your questions What is the typical lifespan of the product? When might it require replacement or updating if hardware or software becomes obsolete over time? Estimated at 10 years if covered by maintenance contract – everything is covered hardware and software.
- Page 16 Is there any future cost associated with this system (such as, maintenance, operation cost, any software subscription, etc.)? And if yes, please provide costing info for our review. As far as operation and maintenance the service contract of 9.95/unit will cover all costs of components replacement, batteries and labor.
- Page 17 What does the cost include? Find the business proposal for your project: Installation It is recommended that you use your own plumber and electrician to install the valves and the power outlets (if not available). Since they know the building well, your Society can save on the installation. Water-Protec or our Authorized Dealers will work with you to reduce the cost of the installation.