1. Manuals
  2. Brands
  3. Ezze Mobile Tech Manuals
  4. Cell Phone
  5. SL599
  6. Technical manual

Ezze Mobile Tech SL599 Technical Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
SL599
1. Product Specification
2. Mechanical Construction
3. Circuit Description
4. IC Information
5. Spare Part List
Ezze Mobile Tech., Inc
Technical Manual
- COMPANY CONFIDENTIAL -
Tel. +82 (0)2 519 7700
Fax. +82 (0)2 519 7882

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the SL599 and is the answer not in the manual?

Questions and answers

Related Manuals for Ezze Mobile Tech SL599

Summary of Contents for Ezze Mobile Tech SL599

  • Page 1 SL599 Technical Manual 1. Product Specification 2. Mechanical Construction 3. Circuit Description 4. IC Information 5. Spare Part List - COMPANY CONFIDENTIAL - Tel. +82 (0)2 519 7700 Ezze Mobile Tech., Inc Fax. +82 (0)2 519 7882...
  • Page 2 Section 1 – Product Specification Contents Page SL599 specifications ..……...…………..……………………………………………… Standard charger …………………………..…………………………………………. Batteries ………………………………..…………….………………………………… - COMPANY CONFIDENTIAL - Tel. +82 (0)2 519 7700 Ezze Mobile Tech., Inc Fax. +82 (0)2 519 7882...
  • Page 3 Section 2 – Mechanical Construction Contents Page Disassembly ……………………………………………………………………………... 2.1 Phone disassembly …………………………..……………………………….……… ... 2.2 Phone Assembly ………………………………………………………………………… 2.6 - COMPANY CONFIDENTIAL - Tel. +82 (0)2 519 7700 Ezze Mobile Tech., Inc Fax. +82 (0)2 519 7882...

  • Page 4: Table Of Contents

    MT6120 ( RF Transceiver IC ) …………………………………………………………… 3.46 RF3146 ( QUAD-BAND Power Amplifier Module ) ………………………………….3.49 LMSP54HA-348TEMP ( Antenna Switch Module for Tri Band ) ………………… 3.51 - COMPANY CONFIDENTIAL - Tel. +82 (0)2 519 7700 Ezze Mobile Tech., Inc Fax. +82 (0)2 519 7882...
  • Page 5 Pin out for U600 …………………..…………………………………………………….. 4.23 Pin out for U100 ……………………………………………………………………..4.26 Pin out for U350 ……………………………………………………………………..4.37 Pin out for U300 ……………………………………………………………………..4.39 - COMPANY CONFIDENTIAL - Tel. +82 (0)2 519 7700 Ezze Mobile Tech., Inc Fax. +82 (0)2 519 7882...
  • Page 6 Section 5 – Spare Part List Contents Page SL599 Part List ………………………………………………………………………... - COMPANY CONFIDENTIAL - Tel. +82 (0)2 519 7700 Ezze Mobile Tech., Inc Fax. +82 (0)2 519 7882...
  • Page 7 Page SL599 Specifications General specification Trial Band EGSM900 Class 4/DCS class 1 handheld cellular telephone Type approval No. SL599 Dimensions (mm): Including 680mAh Li-Ion battery Standard: 85 (L) x 45 (W) x 15.6 (D) Weight: Including 680mAh Li-Ion battery Standard: about 75 grammes...
  • Page 8 Model SL599 Version V_1.0 Prepared by Date 2007.04.24 Subject Technical Manual Page Support Phase 2 plus Feature 64 Poly stereo sounds Graphics and animated icons Phone memory location (200 numbers) Dynamic text display Easy text input (T9) SIM application tool kit...
  • Page 9 Model SL599 Version V_1.0 Prepared by Date 2007.04.24 Subject Technical Manual Page Battery Connector Function Description VBat Battery Supply Pin(Right) Battery ID Battery ID Resistor Pin 10Kohm(Middle) GND(Left) I/O Connector layout Pin description Pin 1 EJ_Out_L Headset Receiver Left EJ_Out_R...
  • Page 10 Page Standard charger SL599 is supplied with a linear charger as standard. The charger is connected to the transceiver through the bottom port. Charging of the battery can only be carried out when the battery is fitted to the phone. There are no serviceable parts within the main plug.
  • Page 11 Model SL599 Version V_1.0 Prepared by Date 2007.04.24 Subject Technical Manual Page Batteries Standard Battery 500mAh Li-Ion(Min) Type: Lithium Ion Rechargeable Battery Capacity 25°C: 680mAh Standby time: up to 100 hours. Talk time (900MHZ): 33dBm: 2.5 hours 3 hours* Charging time: 1½-2 hours approximately to full capacity.
  • Page 12 1/11 Disassembly This section covers the assembling and disassembly of the phone named SL599. In order to carry out the assembling or disassembly the following precautions should be taken: 1. A Plus screwdriver is required to remove the screws, which holds the two casings together.
  • Page 13 Model SL599 Version V_0.1 Prepared by Date 2007.04.24 Subject Technical Manual Page 2/11 1. Battery Cover Disassembly A. Shove battery cover out along the direction of arrow and remove battery cover. B. Take out the battery along the direction of arrow and remove battery.
  • Page 14 Model SL599 Version V_0.1 Prepared by Date 2007.04.24 Subject Technical Manual Page 3/11 A. Take off screw caps. B. Loosen the screws C. Disjoin D cover D. Disjoin the SIM holder E. Disjoin BtoB connector F. Take out the USB cap, ear cap, volume key ASS’Y, camera key ASS’Y and IRDA lens G.
  • Page 15 Model SL599 Version V_0.1 Prepared by Date 2007.04.24 Subject Technical Manual Page 4/11 B. Loosen the 4 screws C. Disjoin the A cover ASS’Y D. Disjoin the LCD cover E. Disjoin the LCD module F. Take off the LCD cushion G.
  • Page 16 Model SL599 Version V_0.1 Prepared by Date 2007.04.24 Subject Technical Manual Page 5/11 6. C cover Disassembly A. Remove Hinge contact 7. B cover assembling A. Press the hinge to outside...
  • Page 17 Model SL599 Version V_0.1 Prepared by Date 2007.04.24 Subject Technical Manual Page 6/11 B. Remove the “magnetic” C. Remove the LCD double side tape 8. A cover Disassembly A. Put off the camera window, camera window double side tape, reflector, LED tape and camera cushion .
  • Page 18 Model SL599 Version V_0.1 Prepared by Date 2007.04.24 Subject Technical Manual Page 7/11 B. Put the “camera cushion” on the inside of A cover C. Put the “LED tape and Reflector” on the inside of A cover and . D. Put the “camera window double side tape and camera window” on the out side of A cover 2.
  • Page 19 Model SL599 Version V_0.1 Prepared by Date 2007.04.24 Subject Technical Manual Page 8/11 4. C cover assembling with B cover A. Put the “main FPCB in the other side of the hinge hole of B cover and C cover. 5. Folder assembling with C cover...
  • Page 20 Model SL599 Version V_0.1 Prepared by Date 2007.04.24 Subject Technical Manual Page 9/11 B. Put the “LCD module” in the LCD hole of the B cover C. Put the “LCD cover on the Sub LCD side D. Close the “A cover ASS’Y” with B cover E.
  • Page 21 Model SL599 Version V_0.1 Prepared by Date 2007.04.24 Subject Technical Manual Page 10/11 B. Put the main PCB ASS’Y on the keypad. C. Join BtoB connector on the main FPCB with BtoB on the main PCB D. Join the SIM holder with main PCB.
  • Page 22 Model SL599 Version V_0.1 Prepared by Date 2007.04.24 Subject Technical Manual Page 11/11 8. Battery & Battery Cover Assembly A. Put the battery in. B. Put the battery in and shove battery cover in along the direction of arrow.

  • Page 23: Baseband Section

    ANUAL Baseband section This document provides a description of the baseband section of the SL599. Most design decisions are explained, but no detailed calculations are included. Total chip solutions(MT6227, MT6305, MT6120) except for RF Power Amplifier(RF3146) are from Media Tek, Taiwan.
  • Page 24 SL599 V_1.0 ODEL ERSION 2007.04.11 REPARED BY 2/52 UBJECT ECHNICAL ANUAL Figure 2 is shown the Block Diagram of MT6227 for detail Figure 2 : Block Diagram of MT6227 SL599 T ECHNICAL ANUAL...
  • Page 25 2.1 Pin Outs One type of Package for this product, TFBGA 13x13mm, 296balls, 0.65mm pitch package, is offerd. Pin outs and the top view are illustrated in Figure 3,4. Figure 3 . MT6227 Pin Out(Top View). SL599 T ECHNICAL ANUAL...
  • Page 26 SL599 V_1.0 ODEL ERSION 2007.04.11 REPARED BY 4/52 UBJECT ECHNICAL ANUAL -. Top and Bottom View Figure 4.Top and Bottom View 2.2 Top Masking Definition Figure 5. Top masking definition SL599 T ECHNICAL ANUAL...
  • Page 27 SL599 V_1.0 ODEL ERSION 2007.04.11 REPARED BY 5/52 UBJECT ECHNICAL ANUAL 2.3 Pin Description -. JTAG Port -. RF Parallel Control Unit -. RF Serial Control Unit -. PWM Interface -. Serial LCD/PM IC Interface SL599 T ECHNICAL ANUAL...
  • Page 28 SL599 V_1.0 ODEL ERSION 2007.04.11 REPARED BY 6/52 UBJECT ECHNICAL ANUAL -. Parallel LCD/Nand_Flash Interface -. SIM Card Interface SL599 T ECHNICAL ANUAL...
  • Page 29 SL599 V_1.0 ODEL ERSION 2007.04.11 REPARED BY 7/52 UBJECT ECHNICAL ANUAL -. Dedicated GPIO Interface -. Miscellaneous -. Key Pad Interface -. External Interrupt Interface SL599 T ECHNICAL ANUAL...
  • Page 30 SL599 V_1.0 ODEL ERSION 2007.04.11 REPARED BY 8/52 UBJECT ECHNICAL ANUAL -. External Memory Interface SL599 T ECHNICAL ANUAL...
  • Page 31 SL599 V_1.0 ODEL ERSION 2007.04.11 REPARED BY 9/52 UBJECT ECHNICAL ANUAL -. USB Interface -. Memory Card Interface -. UART Interface -. Digital Audio Interface SL599 T ECHNICAL ANUAL...
  • Page 32 SL599 V_1.0 ODEL ERSION 2007.04.11 REPARED BY 10/52 UBJECT ECHNICAL ANUAL -. Image Sensor Interface -. Analog Interface SL599 T ECHNICAL ANUAL...
  • Page 33 SL599 V_1.0 ODEL ERSION 2007.04.11 REPARED BY 11/52 UBJECT ECHNICAL ANUAL -. VCXO Interface -. RTC Interface SL599 T ECHNICAL ANUAL...
  • Page 34 SL599 V_1.0 ODEL ERSION 2007.04.11 REPARED BY 12/52 UBJECT ECHNICAL ANUAL -. Supply Voltages SL599 T ECHNICAL ANUAL...
  • Page 35 Before data transfer can be established, bus master must ask for bus ownership. This is accomplished by request-grant handshaking protocol between masters and arbiters. Figure 6. Block Diagram of MCU in MT6227 SL599 T ECHNICAL ANUAL...
  • Page 36 Figure 7. Memory Layout of MT6227 External Memory Access To allow external access, The MT6227 outputs 26bits(A25~A0) of address line along with 8 selection signals that correspond to associated memory blocks. This is, MT6227 can support up to 8 MCU SL599 T ECHNICAL ANUAL...
  • Page 37 In addition, since the base address of each APB slave has been associated with select signals, the address bus on APB will contain only the value of offset address. The base address and data width of each peripheral are listed in below table. SL599 T ECHNICAL ANUAL...
  • Page 38 SL599 V_1.0 ODEL ERSION 2007.04.11 REPARED BY 16/52 UBJECT ECHNICAL ANUAL SL599 T ECHNICAL ANUAL...
  • Page 39 This controller generates two request signals : FIQ for fast, low latency interrupt request and IRQ for more general interrupts with lower priority. Figure 10. Block Diagram of Interrupt controller. SL599 T ECHNICAL ANUAL...
  • Page 40 All these parameters are based on cycle time of system clock. External Memory Interface of MT6227 for Asynchronous/Synchronous components. In SL599, ECS0# is used for External Flash Memory and ECSL599# is used for External PSRAM. SL599 T...
  • Page 41 KEYPAD IRQ will be issued. The MCU can then read the key pressed directly in KP_HI_KEY, KP_MID_KEY and KP_LOW_KEY register. In SL599, The 6 Rows are used (Row0 ~Row5) and The 5 Columns are used (Col 0~3 and Col 6) SL599 T...
  • Page 42 The baseband chipset houses three UARTs. The UARTs provide full duplex serial communication channels between baseband chipset and external devices. In SL599, UART1(URXD1, UTXD1) is used for Factory Programming and UART3(URXD3, UTXD3) is used for Blue Tooth Programming. SL599 T...
  • Page 43 BOFs removal, ESC character removal, CRC checking and EOF detection. In addition, the framer will perform 3/16 modulation and demodulation to connect to the IR transceiver. The transmitter and receiver all need DMA channel. Figure 15. IrDA Block Diagram. SL599 T ECHNICAL ANUAL...
  • Page 44 The Maximum day-of-month values, which depend on the leap year condition, are stored in the RTC block. In SL599, Big Capacitor Battery(BAT100) is used for Backup Battery. The Charging Voltage is about 1.5V by VRTC.
  • Page 45 SRAM or external SRAM/Flash Memory to the off-chip LCD modules. Figure 16. LCD interface block diagram. In SL599, The 262K color TFT LCD Module is used with Samsung Driver IC – S6D0133. The Resolution is 176x220 dots and 1.66inch Panel from Han Star.
  • Page 46 DP and DM signals to make the output impedance equivalent to 28~44ohm. Also, USB cable can be used to Charger for 5V input. The ADC4_USB is to monitor whether USB cable is inserted or not. SL599 T ECHNICAL ANUAL...
  • Page 47 The controller fully supports the SD Memory Card bus protocol as defined in SD Memory Card Specification Part1 Physical Layer Specification version1.0. But SL599 is not interfaced Mini SD card but T-Flash Memory Card. Interface Signals are same. Normally, the Detection is controlled by INS pin status. When Card is nothing, The INS is high logically.
  • Page 48 ANUAL Card Detection Figure 21. Card Detection. In SL599, The INS pin is always VSS. Because T-Flash Connector does not have a Detection Pin. So, The Detection is done by Software programming. 6.7 Camera Interface Figure 22. Rich Image Processor MT6227 incorporates a feature rich image signal processor to connect with a variety of image sensor components.
  • Page 49 SL599 V_1.0 ODEL ERSION 2007.04.11 REPARED BY 27/52 UBJECT ECHNICAL ANUAL Figure 23. Camera Sensor Interface circuit. SL599 T ECHNICAL ANUAL...
  • Page 50 Besides, there is a Digital Audio Interface(DAI) block to communicate with the System Simulator for FTA or external Bluetooth module for particular applications. The digital filter block performs filter operations for voice band and audio band signal processing. SL599 T ECHNICAL ANUAL...
  • Page 51 Figure 25. The block diagram of the digital circuits for Audio Front-End Stereo sound are implemented by TS4990 IC(Audio amplifier). SL599 used single speaker. The AU_Out0_N/_P lines are for Voice Audio and AU_MOUTL/R are for Ring Tone and Melody(Midi and MP3).
  • Page 52 The Baseband Parallel Interface features a 10-pin output bus used for timing-critical control of the external circuits. These pins are typically used to control front-end components at the specified time along the GSM time- base, such as transmit-enable(PA_EN), band switching(BANDSW_DCS), TR-switch(LB_TX, HB_TX), etc. Figure 27. Baseband Parallel Interface Block Diagram. SL599 T ECHNICAL ANUAL...
  • Page 53 D/A converter. The block diagram of the APC unit is shown in Figure 28. Figure 28. Block diagram of APC unit In SL599, The APC Analog Signal is inputted to Power Amplifier Module through Low Pass filter (R400,C406) The APC Analog Signal has 32 Ramp profiles for Up Ramp and Down Ramp each 16 profiles.
  • Page 54 FIR filtering and then sends results to DSP. The uplink path is mainly composed of GMSK Modulator and uplink parts of Baseband Serial Ports, and the downlink path is mainly composed of RX digital FIR filter SL599 T ECHNICAL...
  • Page 55 On downlink path, the sub-block between RX mixed-signal module and Baseband Serial Ports is RX Path. It mainly consists of a digital FIR filter, two sets of multiplexing paths for loopback modes, interface for RX mixed-signal module and interface for Baseband Serial Ports. Figure 32. Block Diagram of RX Path SL599 T ECHNICAL ANUAL...
  • Page 56 32.768KHz crystal oscillator. The 32.768KHz oscillator is not accurate and therefore it should be calibrated prior to entering pause mode. Figure 34. The Block Diagram of TDMA Timer. SL599 T ECHNICAL ANUAL...
  • Page 57 The Operating modes of MT6227 as well as main power states provided by the PMIC are shown in Figure 36. Figure 36. Major Phone Power States and Operation Modes for MT6219 based terminal SL599 T ECHNICAL ANUAL...
  • Page 58 Two 1/2-dividers, one for MCU Clock and the other for DSP Clock, exist to allow usage of 26 or 13Mhz TXVCXO as clock input. There phase-locked loops(MPLL, DPLL and UPLL) are used to generate three primary clocks. MPLL : Provides the MCU System Clock. SL599 T ECHNICAL ANUAL...
  • Page 59 These are local reset signals that initialize specific hardware. For example, The MCU or DSP software may write to software reset trigger registers to reset hardware modules to their initial states, when hardware failures are detected. The following Modules has software resets DSP Core DSP Coprocessors. SL599 T ECHNICAL ANUAL...

  • Page 60: Mt6305Bn ( Gsm Power Management System)

    Li-Ion and NiMH battery Charge function SIM Card interface Three Open-Drain Output Switches to Control the LED, Alerter and vibrator Thermal Overload Protection Under Voltage Lock-Out Protection Over Voltage Protection Power on Reset And start up Timer SL599 T ECHNICAL ANUAL...
  • Page 61 1.8V. It supplies the baseband circuitry in the handset. The LDO is optimized for very low quiescent current. 3. Digital IO LDO (DVDD) The digital IO LDO is a regulator that could source 100mA with 2.8V output voltage. It supplies the baseband circuitry in the handset. 4. Analog LDO (AVDD) SL599 T ECHNICAL ANUAL...
  • Page 62 It provides level shifting needs for low voltage GSM controller to communicate with either 1.8V or 3V SIM cards. In SL599, 3V SIM card is applied. All SIM cards contain a clock input, a reset input, and a bi-directional data input/output. The clock and reset inputs to SIM cards are level shifted from the supply of digital IO of baseband chipset to the SIM supply.
  • Page 63 MT6305 is available pulsed top-off charging algorithm by the CHRCNTL pin control from baseband chipset. Figure 27. Charger and Voltage Detection Figure 28. Li-Ion Battery Charging Profile. SL599 T ECHNICAL ANUAL...

  • Page 64: M ( C-Mos Camera Module )

    ECHNICAL ANUAL III. 2.0M ( CMOS Camera Module ) SL599-2.0M is a CMOS Camera Module which supports 2.0Mega Pixel CMOS sensor in SL599. CCM used the Samsung which supports 1600 X 1200 SXGA format and 1/4 inch optical (S5K4BAFA) format.

  • Page 65: Lrs18Ca( Mcp )

    72-pin BGA package making it suitable for a variety of applications. The Boot block architecture for flash memory is a bottom boot block. Figure 30. MCP Block diagram SL599 T ECHNICAL ANUAL...

  • Page 66: Mt6188( Fm Radio )

    5bit RSSI indicator, IF counter, FM demodulator, stereo decoder, and an inter- grated VCO with only one off-chip inductor. The MT6188 includes control circuits to implement different operating modes. The device is housed in a small size 28-pin LGA SMD package. Figure 32. Block Diagram SL599 T ECHNICAL ANUAL...

  • Page 67: Btvz0502Sa ( Blue Tooth Module )

    Ⅵ. BTVZ0502SA ( Blue Tooth Module ) This specification covers Bluetooth module (class-2) which complies with Bluetooth specification Version1.2 and integrates RF & Baseband controller in small package. This module has deployed CSR's BC03-ROM CSP chipset. Figure 33. Block Diagram SL599 T ECHNICAL ANUAL...

  • Page 68: Rf Section

    IQ demodulator for the receiver, a precision IQ modulator with offset PLL for the transmitter, two internal TX VCOs, a VCXO, on-chip regulators, and a fully programmable sigma- delta fractional-N synthesizer with an on-chip RF VCO. Figure 34. MT6120 Functional block diagram SL599 T ECHNICAL ANUAL...
  • Page 69 MT6120 can reach 35dB for all bands. Compared to a direct conversion receiver(DCR), MT6120’s very low-IF architecture improves the blocking rejection, AM suppression, as well as the adjacent channel interference performance. The SL599 was designed for Tri-Band(EGSM900, DCS1800,PCS1900) Receiver Input Frequency Mode...
  • Page 70 Fvco = D1*Fch/(D1-1) for PCSL599900. The MT6120 uses a digital calibration technique to reduce the PLL settling time Once the RF synthesizer is programmed through a 3-wire serial interface, the calibration loop is activated. The main SL599 T ECHNICAL ANUAL...
  • Page 71 Output Frequency is 26Mhz. When VCXOFRQ pin is low, Output Frequency is 13Mhz. VCXOFRQ is High in SL599. The Amplifier is designed to be in series resonance with a standard 26Mhz crystal. The Crystal is connected from the Input pin XAL of Amplifier to ground through a series load capacitance.
  • Page 72 Analog voltage input. The RF3146 has Max +35dBm GSM output power and Max +33dBm PCS output power at 3.5V. Figure 36. The Shaded area are eliminated on RF3146. Figure 37. Diagram of the power control Figure 38. Diagram of the Power control SL599 T ECHNICAL ANUAL...

  • Page 73: Lmsp54Ha-348Temp ( Antenna Switch Module For Tri Band )

    LMSP54HA-348TEMP is an Antenna Switch Module for EGSM900/DCS1800 of Murata with Three SAW Modules. Control Pins (VC1, VC2, VC3) are connected to LB_TX, HB_TX,PCB (signals from baseband processor). The Control Pins Operating range is 2.4V 2.8V. Figure 35. The Evaluation board and control logic of LMSP54HA-349TEMP SL599 T ECHNICAL ANUAL...
  • Page 74 SL599 V_1.0 ODEL ERSION 2007.04.11 REPARED BY 52/52 UBJECT ECHNICAL ANUAL The EGSM900/DCS1800 input port matching impedances are 50 ohm. The EGSM900/DCS1800 (Balance) output port matching impedance are 150ohm. SL599 T ECHNICAL ANUAL...
  • Page 75 PIN NO FUNCTION NAME GSM900 RX1 GSM900 RX1 GSM900 RX2 GSM900 RX2 DCS1800 RX1 DCS1800 RX1 DCS1800 RX2 DCS1800 RX2 PCS1900 RX1 PCS1900 RX1 PCS1900 RX2 PCS1900 RX2 DCS/PCS TX DCS/PCS TX GSM TX GSM TX SL599 Technical Manual Page 1...
  • Page 76 Model SL599 Version V_1.0 Prepared by Date 2007.04.10 Subject Technical Manual Page 2/39 Pin out for U601 (CSX-325T26BADT-J2E) SL599 Technical Manual Page 2...

  • Page 77: Pin Out For Bat

    Model SL599 Version V_1.0 Prepared by Date 2007.04.10 Subject Technical Manual Page 3/39 Pin out for BAT200 (TS414H I106E) PIN NO FUNCTION NAME Ground SL599 Technical Manual Page 3...

  • Page 78: Pin Out For Con

    Model SL599 Version V_1.0 Prepared by Date 2007.04.10 Subject Technical Manual Page 4/39 Pin out for CON400 (24-5805-054-000-829+) SL599 Technical Manual Page 4...

  • Page 79: Pin Out For Cn

    Model SL599 Version V_1.0 Prepared by Date 2007.04.10 Subject Technical Manual Page 5/39 Pin out for CN10 (11TFC-0030824) PIN NO FUNCTION NAME MCDA2 DAT2 MCDA3 CD/DAT3 MCCMO MCCK GROUND MCDA0 DAT0 MCDA1 DAT1 SL599 Technical Manual Page 5...
  • Page 80 Version V_1.0 Prepared by Date 2007.04.10 Subject Technical Manual Page 6/39 Pin out for U20 (A3212EEHLT) PIN NO FUNCTION NAME Output OUTPUT No connection NO CONNECTION GROUND GROUND No connection NO CONNECTION Power supply SUPPLY SL599 Technical Manual Page 6...
  • Page 81 Model SL599 Version V_1.0 Prepared by Date 2007.04.10 Subject Technical Manual Page 7/39 Pin out for U700 (TS4990IJT) PIN NO FUNCTION NAME GROUND BYPASS SHUTDOWN GROUND SL599 Technical Manual Page 7...
  • Page 82 Model SL599 Version V_1.0 Prepared by Date 2007.04.10 Subject Technical Manual Page 8/39 Pin out for U111, U351 (XC6219B282MR) SL599 Technical Manual Page 8...
  • Page 83 Model SL599 Version V_1.0 Prepared by Date 2007.04.10 Subject Technical Manual Page 9/39 Pin out for U550 (RF3146) SL599 Technical Manual Page 9...
  • Page 84 Internal circuit node. Do not externally connect. Ramping signal from DAC. VRAMP Controlled voltage on the GSM preamplifier stage. VCC1 GSM Ground for the GSM preamplifier stage. GND1 GSM GSM RF input GSM 850 / 900 IN Pkg Base Ground SL599 Technical Manual Page 10...
  • Page 85 Model SL599 Version V_1.0 Prepared by Date 2007.04.10 Subject Technical Manual Page 11/39 Pin out for F450 (0467 001.NR) SL599 Technical Manual Page 11...
  • Page 86 Microprocessor Control Input Signal for Gate CHRCNTL Drive, Internal Pull Low to DGND. Charger Detect Output CHRDET Battery Input Voltage Sense BATSNS SIM Supply VSIM Non-Level-Shifted Bidirectional Data I/O SIMIO Non-Level-Shifted SIM Reset Input, Internal SIMRST SL599 Technical Manual Page 12...
  • Page 87 Li-ion, Internal Pull Low to DGND Battery Detect Input, Low for Battery VMSEL Connected, Internal Pull High for Battery Disconnected VBAT High for VA enabled with VTCXO, Low for VA VCORE enabled with VD, Internal Pull Low to DGND SL599 Technical Manual Page 13...
  • Page 88 Model SL599 Version V_1.0 Prepared by Date 2007.04.10 Subject Technical Manual Page 14/39 High for Vm=2.8V, Low for Vm=1.8V, Internal Pull High to VIO Battery Input Voltage Digital Core Supply SL599 Technical Manual Page 14...

  • Page 89: Pin Out For U

    Model SL599 Version V_1.0 Prepared by Date 2007.04.10 Subject Technical Manual Page 15/39 Pin out for U201 (AO8701) PIN NO FUNCTION NAME Drain Source Source Gate Cathode Anode Anode Anode SL599 Technical Manual Page 15...
  • Page 90 Model SL599 Version V_1.0 Prepared by Date 2007.04.10 Subject Technical Manual Page 16/39 Pin out for U150 (LRS18CA) SL599 Technical Manual Page 16...
  • Page 91 Model SL599 Version V_1.0 Prepared by Date 2007.04.10 Subject Technical Manual Page 17/39 SL599 Technical Manual Page 17...

  • Page 92: Pin Out For

    Model SL599 Version V_1.0 Prepared by Date 2007.04.10 Subject Technical Manual Page 18/39 Pin out for D200, D450, D451(RB520S-30 PIN NO FUNCTION NAME Anode Cathode SL599 Technical Manual Page 18...

  • Page 93: Pin Out For D30 - D41

    Model SL599 Version V_1.0 Prepared by Date 2007.04.10 Subject Technical Manual Page 19/39 Pin out for D30 – D41 (SSC-SB104-IT) PIN NO FUNCTION NAME Anode Cathode SL599 Technical Manual Page 19...

  • Page 94: Pin Out For Zd100 - Zd102

    Model SL599 Version V_1.0 Prepared by Date 2007.04.10 Subject Technical Manual Page 20/39 Pin out for ZD100~ZD102, (LCA142A1A) PIN NO FUNCTION 1,3,5,7 Input 2,4,6,8 Output 9,10 Ground SL599 Technical Manual Page 20...

  • Page 95: Pin Out For Zd403 - Zd405

    Model SL599 Version V_1.0 Prepared by Date 2007.04.10 Subject Technical Manual Page 21/39 Pin out for ZD403~ZD405, (KNA16300) PIN NO FUNCTION 1,3,5,7 Input 2,4,6,8 Output 9,10 Ground SL599 Technical Manual Page 21...

  • Page 96: Pin Out For D500

    Model SL599 Version V_1.0 Prepared by Date 2007.04.10 Subject Technical Manual Page 22/39 Pin out for D500 (PG05HSUSC PIN NO FUNCTION NAME Anode Cathode SL599 Technical Manual Page 22...

  • Page 97: Pin Out For U600

    TX VCO supply voltage and Regulator 1 (TX VCCTXVCO VCO) voltage output Regulator 1 external noise bypass capacitor CREG1 Battery supply for Regulator1 VBAT1 TRX RF and TX BUF block supply voltage and VCCRF Regulator 1 (TRX) voltage output SL599 Technical Manual Page 23...
  • Page 98 GNDVCXO varactor VCXOFRQ 26MHz crystal reference input GNDMOD VCXO supply voltage VCCMOD 13MHz / 26 MHz reference buffer output VCXO ground GNDD Reference output buffer 13MHz / 26MHz VCCD selection Synthesizer Sigma-Delta modulator ground ENRFVCO SL599 Technical Manual Page 24...
  • Page 99 Transmitter charge pump supply voltage TXODPCS No connection Transmitter charge pump ground TX VCO buffer transmit output for GSM TX VCO ground No connection TX VCO ground TX VCO buffer transmit output for DCS / PCS SL599 Technical Manual Page 25...

  • Page 100: Pin Out For U100

    Model SL599 Version V_1.0 Prepared by Date 2007.04.10 Subject Technical Manual Page 26/39 Pin out for U100 (MT6227 SL599 Technical Manual Page 26...
  • Page 101 Version V_1.0 Prepared by Date 2007.04.10 Subject Technical Manual Page 27/39 -. JTAG P -. RF P ARALLEL ONTROL -. RF S ERIAL ONTROL -. PWM I NTERFACE -. S LCD/PM IC I ERIAL NTERFACE SL599 Technical Manual Page 27...
  • Page 102 Model SL599 Version V_1.0 Prepared by Date 2007.04.10 Subject Technical Manual Page 28/39 -. P LCD/N ARALLEL LASH NTERFACE -. SIM C NTERFACE SL599 Technical Manual Page 28...
  • Page 103 Model SL599 Version V_1.0 Prepared by Date 2007.04.10 Subject Technical Manual Page 29/39 -. D GPIO I EDICATED NTERFACE -. M ISCELLANEOUS -. K NTERFACE SL599 Technical Manual Page 29...
  • Page 104 Model SL599 Version V_1.0 Prepared by Date 2007.04.10 Subject Technical Manual Page 30/39 -. E XTERNAL NTERRUPT NTERFACE -. E XTERNAL EMORY NTERFACE SL599 Technical Manual Page 30...
  • Page 105 Model SL599 Version V_1.0 Prepared by Date 2007.04.10 Subject Technical Manual Page 31/39 -. USB I NTERFACE -. M EMORY NTERFACE SL599 Technical Manual Page 31...
  • Page 106 Model SL599 Version V_1.0 Prepared by Date 2007.04.10 Subject Technical Manual Page 32/39 -. UART I NTERFACE -. D IGITAL UDIO NTERFACE -. I MAGE ENSOR NTERFACE SL599 Technical Manual Page 32...
  • Page 107 Model SL599 Version V_1.0 Prepared by Date 2007.04.10 Subject Technical Manual Page 33/39 -. A NALOG NTERFACE SL599 Technical Manual Page 33...
  • Page 108 Model SL599 Version V_1.0 Prepared by Date 2007.04.10 Subject Technical Manual Page 34/39 -. VCXO I NTERFACE -. RTC I NTERFACE -. S UPPLY OLTAGES SL599 Technical Manual Page 34...
  • Page 109 Model SL599 Version V_1.0 Prepared by Date 2007.04.10 Subject Technical Manual Page 35/39 SL599 Technical Manual Page 35...
  • Page 110 Model SL599 Version V_1.0 Prepared by Date 2007.04.10 Subject Technical Manual Page 36/39 -. A NALOG UPPLIES SL599 Technical Manual Page 36...

  • Page 111: Pin Out For U350

    Model SL599 Version V_1.0 Prepared by Date 2007.04.10 Subject Technical Manual Page 37/39 Pin out for U350 (BTVZ0502SA SL599 Technical Manual Page 37...
  • Page 112 Model SL599 Version V_1.0 Prepared by Date 2007.04.10 Subject Technical Manual Page 38/39 SL599 Technical Manual Page 38...

  • Page 113: Pin Out For U300

    Stereo block power supply input Ground Ground FM demodulated output Hardware interrupt 2wire Latch SDA_DATA I2C/3wire serial data SCL_CLK I2C/3wire serial clock input BUS_S Selection of I2C or 3wire mode Power Digital power supply input SL599 Technical Manual Page 39...
  • Page 114 Version V_1.0 Prepared by Date 2007.04.25 Subject Technical Manual Page Technical spare parts list for SL599 1. Main DESCRIPTION Q'TY REFERENCE N/O CHIP RES 1005 1/16W 5% R350, R550, R650, R652, R701, R711, L550 L453, L454 CHIP RES 1608 1/10W 5% R705 0.39...
  • Page 115 SL599 Version V_1.0 Prepared by Date 2007.04.25 Subject Technical Manual Page Technical spare parts list for SL599 0.0015UF CHIP CAP 1005 X7R +/-10% 50V C614 0.0033UF MLCC 1005 X7R +/- 10% 50V C303 0.0068UF CHIP CAP 1005 X7R +/-10% 16V C700 0.01UF...
  • Page 116 Model SL599 Version V_1.0 Prepared by Date 2007.04.25 Subject Technical Manual Page Technical spare parts list for SL599 128*64) MT6305BN-L PMIC U200 SI7703EDN P-MOSFET WITH DIODE U201 TS414H II06E BACKUP BATTERY BAT200 MT6188 FM RECEIVER IC U300 BTVZ0502SA SAMSUNG BLUETOOTH...

Table of Contents