Summary of Contents for Flushtech CF107
-
Page 1: Table Of Contents
CF107 Smart Toilet Installation Instructions Table of Contents Product Display Inside Parts Product Features Specification Parts List Operation Care and Cleaning Instructions Installation Instructions Function Test and Adjustment Cautions Troubleshooting Sensor Unit Mounting – Double-Sided Tape Option... -
Page 2: Product Display
CF107 Smart Toilet Installation Instructions Product Display Inside Parts Close Open Sensor ater Pu p Fill al e Flus al e ater Pipe Solenoid al e... - Page 3 Features T e in rared sensor allo s ands- ree lus ing ensuring giene and a bacteria- ree en iron ent uto atic ands- ree lus ing unction is especiall bene icial to t e andicapped elderl in ir ed and oung c ildren T e sensor is po ered b 4 batteries so t ere is no need or a all outlet It is not li ited b an...
- Page 4 Parts ist Sensor Unit Fill al e Unit t 1 Solenoid al e Unit ater Connector t 1 P C Tube t 1 ater Pu p Unit t 1 Fle ible Tube t 1 Peg t 1 in C ain Clips t 1 Filter Unit t 1 Code-Matc ing Tool t 1...
-
Page 5: Operation
Operation . When the user's hand approach the detection zone, the sensor sends a signal to activate the solenoid valve which lifts the flapper and flushes the toilet. . Electronic manual button gives users the option of flushing the toilet by simply pressing the button. Care and Cleaning Instructions eep t e displa panel clean at all ti es to pre ent sensor unction ailure 2 Do not place ea... - Page 6 Installation Instructions Fill Valve Unit 1. Close control stop.See Figure (1). Flush Valve Unit Fig.1 Fig.2 2. Remove the fill valve unit and its connecting pipe.See Figure(2). (The flush valve unit remains in place) 3. Install the filter unit to the control stop .See Figure(3). Filter Unit Fig.3 4.
- Page 7 7. Remove the cover of the battery case on solenoid valve assembly as illustrated in Figure(6). Install Alkaline Type AA batteries. Secure the cover back with a screw. Fig.6 8. Install the flexible tube into the solenoid valve unit.See Figure(7) Install the combined parts into the water connector.See Figure(8) Flexible Tube Solenoid Valve Unit...
- Page 8 11. Install water pump to the top end of the flush valve . Adjust to a proper height then tighten with a butterfly nut. See Figure(11) Screw Water Pump Butterfly Nut Fig.11 PVC Tube Overflow Pipe 12. Insert the PVC tube to the water inlet of the water pump unit. Secure it with a nut. See Figure(11.12) Fig.12 13.
- Page 9 15. Mount sensor unit onto the wall as illustrated in Figure(15)(16).Locate it on the side wall. (See P.11 for instructions when using double sided tape for installation.) Bracket Sensor Unit Drill two holes Fig.15 Screw and Anchor Option . See Figure(15) Using a 1/4”...
- Page 10 Tests and d ust ents 1. Open control stop when finished installation. Turn on the water. As the water fills in the tank. Check the connecting points. Make certain no leaking occurs. 2. Observe water as it fills the tank. Make certain the water stops when it reaches the preset water level. ( Make sure no leaking occurs.) The flush volume varies depending on the level of water.
-
Page 11: Cautions
4. Adjust flushing time: Since the closet is Incomplete flushing , please refer to the chart to adjust the appropriate flush time and obtain an optimum flushing effect.(Adjust only if necessary) FLUSH TIME 1 SEC 2 SEC 3 SEC 4 SEC 5 SEC Factory setting 6 SEC... -
Page 12: Troubleshooting
Troubleshooting Problem Cause Solution to Problem Light doesn't turn on, 1. No batteries installed in the sensor unit or not 1. Replace batteries The toilet doesn't flush installed properly after sensing process 2. Sensor fails 2. Replace sensor unit Light flashes on sensor unit Low battery in the sensor unit Replace batteries 1. -
Page 13: Sensor Unit Mounting - Double-Sided Tape Option
Sensor Unit Mounting – Double-Sided Tape Option Step1. Wipe both the back of the sensor unit and the wall where the sensor unit will be placed. Be sure both surfaces are clean and dry. Step2. Peel off the yellow side of the double-sided tape and place it on the back side of the sensor unit as shown in the illustration.