Summary of Contents for Multi PSI Multi-160
- Page 1 Operator's manual Battery fogger Model : Multi-160 Certified equipment Downloadable manual: www.multibiolab.com...
- Page 2 The warranty service and repair of this product can be contacted by the special dealer : Multi BioLab (Multi PSI). We are committed to the continuous optimization and improvement of product design. If there is a slight discrepancy between this manual and the parameters of the product, we will not inform you.
-
Page 3: Table Of Contents
Contents Parameter ................................5 Working principle ..............................5 Features ...................................5 Fields of application ...............................6 Component identification ............................7 Operating instructions ............................10 Troubleshooting ..............................17 Parts list ................................18 D r o i t d ’ a u t e u r M u l t i P S I . - Page 4 Important safety information 1. Before using the sprayer, make sure the battery is fully charged and the filter cotton is in the filter cotton is not blocked ;; 2. Do not use special working liquid. When adding liquid, be careful not to exceed the maximum capacity to avoid the outflow of the liquid.;...
-
Page 5: Parameter
Parameter Model Multi-160 Parameter Rated Power 120W Battery 18 VDC Battery capacity 2000 mAH 50/60 Hz Frequency 20 minutes Duration of a single job Rated speed 30 000 RPM Tank capacity 800 ml Air flow 160/min Product flow 100-200 ml/min Particle size 40μm... -
Page 6: Fields Of Application
The product adopts the principle of the air flow atomization to spray the solution at high speed and extremely fine mist particles, replacing the traditional artificial immune method, which greatly improves the work efficiency; Evenly and quickly administer by spray to maintain the best efficacy and achieve the goal of comprehension elimination of immunity;... -
Page 7: Component Identification
Component identification Multi-160 Ventilation holes Nozzle cap Component release button Trigger Flow control knob Rubber handle Li-Ion battery Length control knob 800ml solution container D r o i t d ’ a u t e u r M u l t i P S I . - Page 8 Explosive view Multi-160 D r o i t d ’ a u t e u r M u l t i P S I . T o u t e s l e s i n f o r m a t i o n s...
- Page 9 ST2.9*10SCRE O-ring Lock catch Rear cover 22 Needle spring Microswitch Cotton filter Needle set Battery pack Right cover Battery pack pin Switch plunger spring Pipette Left cover Switch plunger Cup-ring Gun-ring Right side cover Suction pipe splint Stpper ST3.5*10SCRE Container 800ml Motor cover Big nut Ꝋ3 flat gasket...
-
Page 10: Operating Instructions
Operating instruction Before use the Multi-160 spray gun, material preparation is the first stage: Please refer to the thinning chart and picture. Material Run out Time (seconde) No thinning required Multi BioLab Disinfectant 25-60 Oil enamel Oil based primer 30-60... - Page 11 2. Adjust the suction tube. a. If spray in an upward direction, the angled end of the suction tube should be pointing toward the rear of the gun ; Suction tube b. If spray in a downward direction, the angled end of the suction tube should be pointing toward the front of the gun.
- Page 12 4. Remove the motor. a. Hold the gun with your hand and press the latch in the direction of the arrow; b. At the same time, hold the motor handle with your hand and rotate it counter clockwise 90º; c. Pull out to remove the motor from the gun. 5.
- Page 13 7. Spray length adjustment: Turn this knob to adjust the round shape from vertical to horizontal. Adjust the required length according to the spraying environment, reduce waste and save material. a. The counterclockwise rotation shortens the length, and when it rotates to the stop position, it is sprayed with the largest circle.
- Page 14 8. Adjusting spray patterns a. The gun psray patterns can be changed from a horizontal oval fan pattern to a round. b. Detailed pattern to a vertical fan pattern by adjusting the nozzle Horizontal 90º Circular 45º Vertical 180º Spray angle adjustment Flow control knob 14 | D r o i t...
- Page 15 9. Open the power switch, pull trigger, the solution will spray from the nozzle. How to spray properly ? Even coat throughout Range 8 to 12 inches Correct : Keep stroke smooth and at even speed. Incorrect : Do not flex wrist while spraying 15 | D r o i t...
- Page 16 Replace nozzle and needle ? When disassembling the nozzle, please pull the trigger first, then press and remove the nozzle. a. As shown in the figure, rotate to remove the needle. b. As shown in the figure, rotate to set up the needle. 16 | D r o i t d ’...
-
Page 17: Troubleshooting
Troubleshooting Problem Cause Solution Little or no material flow 1. Nozzle clogged 1. Clean 2. Suction tube clogged 2. Clean 3. Material volume setting turn too 3. Turn to the left far to the right 4. Suction tube loose 4. Insert 5. -
Page 18: Parts List
Parts list Description Quantity Big nut for nozzle Spray ball Nozzle Gun body Motor Container 800ml 18vdc Battery Charger Tool 18 | D r o i t d ’ a u t e u r M u l t i P S I .
Need help?
Do you have a question about the Multi-160 and is the answer not in the manual?
Questions and answers