Summary of Contents for Byomic SkyDiver 102/640
- Page 1 Byomic Dobson Telescope SkyDiver 102/640 Instructions Manual Gebruikershandleiding Bedienungsanleitung...
- Page 2 Dear user, This product is ideal for anyone who wants to discover their world in a new way. That is why it is easy to operate and maintain; it is robust and has a beautiful design. It is important for you and for us that you can use the telescope safely. For example, we already thought about making this product as safe as possible for use by children when it was being manufactured.
- Page 3 Byomic Dobson Telescope SkyDiver 102/640 OPERATING INSTRUCTIONS INTRODUCTION THIS TELESCOPE HAS BEEN PRODUCED TO PRECISE SPECIFICATIONS. PRIOR TO USING YOUR NEW TELESCOPE, PLEASE READ THE FOLLOWING SETUP AND USAGE INSTRUCTIONS. IT IS IMPORTANT TO PROPERLY ASSEMBLE YOUR TELESCOPE IN ORDER TO ALLOW IT TO FUNCTION PROPERLY.
-
Page 4: Parts And Accessories
Byomic Dobson Telescope SkyDiver 102/640 PARTS & ACCESSORIES A. ELECTRONIC RED DOT FINDER: USED TO LOCATE OBJECTS PRIOR TO USING MAIN TELESCOPE. PLEASE NOTE YOU MUST ALIGN THE FINDER WITH THE MAIN TUBE PRIOR TO INITIAL ASTRONOMICAL OR TERRESTRIAL USE. - Page 5 Byomic Dobson Telescope SkyDiver 102/640 ASSEMBLY INSTRUCTIONS CAUTION: NEVER POINT YOUR TELESCOPE AT THE SUN. VIEWING THE SUN WITH THIS TELESCOPE OR EVEN THE UNAIDED EYE CAN RESULT IN BLINDNESS OR OTHER SERIOUS EYE DAMAGE. REMOVE ALL PARTS FROM BOX AND IDENTIFY THEM.
- Page 6 Byomic Dobson Telescope SkyDiver 102/640 6. PLACE FLAT WASHER ONTO 7. PLACE SPRING WASHER ONTO CENTER BOLT CENTER BOLT 8. THREAD LOCKING KNOB ONTO CENTER BOLT(DO NOT OVER TIGHTEN) 9.(1) REMOVE LOCKING KNOB, 9. (2) ATTACH TUBE AND CRADLE ASSEMBLY...
- Page 7 Byomic Dobson Telescope SkyDiver 102/640 10. ATTACH TUBE ASSEMBLY TO THE SIDE PANEL PLACE METAL WASHER AND THEN SPRING WASHER TO BOLT, THEN TIGHTEN THE LOCKING KNOB (DO NOT OVER TIGHTEN) 11. ALIGN THE BOTTOM OF RED DOT FINDER TO THE GROOVE OF THE FINDER BASE, THEN SLIDE THE BOTTOM TO FINDER BASE.
- Page 8 Byomic Dobson Telescope SkyDiver 102/640 WHEN LOCATING AND CENTERING AN OBJECT TO OBSERVE, MANUALLY MOVE THE Byomic SkyDiver DOBSONIAN MOUNT "SIDE TO SIDE" AND "UP AND DOWN" AS SHOWN IN THE ABOVE IMAGE. THE COLLIMATION SPOT ON THE PRIMARY MIRROR IS FOR THE OPTICAL ALIGNMENT...
- Page 9 Byomic Dobson Telescope SkyDiver 102/640 FEATURES OF BYOMIC SKYDIVER 102/640 EYEPIECES F20mm F6MM 3x BARLOW...
- Page 10 HOW TO USE EYEPIECES & ACCESSORIES PROPER PLACEMENT OF THE EYEPIECES AND ACCESSORIES ARE IMPORTANT IN ORDER TO ASSURE EASY OPERATIONS AND CLEAR VIEWING. PLEASE CONSIDER USING YOUR ACCESSORIES IN THE FOLLOWING ORDER. BY DOING THIS YOU WILL BETTER UNDERSTAND THE IMPACT EACH INDIVIDUAL ACCESSORY HAS ON THE FUNCTION OF YOUR TELESCOPE.
- Page 11 ELECTRONIC RED DOT FINDER MOUNTING & ALIGNMENT TO MOUNT: 1) REMOVE ELECTRONIC RED DOT FINDER FROM BOX. 2) LOOSEN THUMB SCREWS ON SIDE OF FINDER AND SLIDE FINDER ONTO DOVETAIL MOUNT LOCATED AT TOP OF MAIN TELESCOPE TUBE. 3) TIGHTEN THUMB SCREWS. TO CHECK ALIGNMENT WITH MAIN TELESCOPE:(IMPORTANT!) 1) THE ELECTRONIC RED DOT FINDER IS NOT PRE-SET AT FACTORY.
-
Page 12: Using The Barlow Lens
USING THE BARLOW LENS AS STATED EARLIER IN THE INSTRUCTIONS, THE BARLOW LENS INCREASES THE POWER OF THE EYEPIECES BY 3 TIMES. TO USE SIMPLY INSERT THE BARLOW LENS INTO THE MAIN FOCUSING TUBE AND THEN PUT THE DESIRED EYEPIECE INTO THE RECEIVING END OF THE BARLOW LENS PLEASE REMEMBER, THE HIGHER THE POWER YOU USE THE DARKER THE IMAGE WILL APPEAR.