Summary of Contents for Dr.Schulze DBF 200
- Page 1 DR. SCHULZE GMBH Original Instructions manual Floor Milling Cutter DBF 200 & DBF 200-B Serial number:...
-
Page 2: Table Of Contents
8. TROUBLESHOOTING ..............................7 9. GENERAL SAFETY INFORMATION ..........................8 10. STORAGE ................................9 11. RECYCLING................................9 12. DECLARATION OF CONFORMITY ..........................9 13. EXPLODED VIEW ..............................10 14. CIRCUIT DIAGRAM DBF 200 ..........................15 15. SPARE PARTS LIST ..............................16... -
Page 3: Introduction & Description
200 and DBF 200-B. Special attention should be paid to the section entitled ‘Safety Precautions’. Milling cutter DBF 200 and DBF 200-B is intended to milling of concrete, stone, paving, bitumen, natural stone, and the elimination of adhesives, lacquers and deposits and for roughage too smooth areas. Is ideal as auxiliary machine when other methods of preparation surfaces - blasting, grinding. -
Page 4: Main Parts Of The Machine
(6) Milling drum with milling segments with removable forehead and sucking throat (7) Wiring with switch and plug connection (electro version) (8) Honda motor with the accessories 2. TECHNICAL DATA Type DBF 200 DBF 200-B Motor / Engine Single-Phase 230 V Honda GSX 160 Motor / Engine Power 2.2 kW... -
Page 5: Assembly And Installation
5.1 Assembly and installation For handling for short distance are only two people needed. To transport for longer distances, it is recommended to use mechanization or means of transport. Producer recommended in depending on the area in a vehicle and secured against overturning or displacement of the machine during braking or changing direction to ensure the cutter using fasteners to avoid damage. -
Page 6: Requirements And Prohibitions
• during operation must take care to avoid distorting suction hose or run over to the power supply cable • while rotating it is necessary the cutter lift by the handle, and after the rotation in the desired direction it is necessary to run slowly in order to continuously mesh of milling segments •... -
Page 7: Requirements
7. MAINTENANCE & CARE The DBF 200 and DBF 200-B Floor Milling Cutter must remain in a condition which is safe for operation at all times, and therefore certain maintenance is needed. Please read the instructions below carefully before any service work is commenced. -
Page 8: Maintenance And Implementation Terms
Without a properly mounted front head is forbidden to operate the machine! 7.5 Repairs Possible repairs of milling cutter DBF 200 and DBF 200-B are recommended to send directly to the producer or person/company who is recommended by producer. -
Page 9: General Safety Information
9. GENERAL SAFETY INFORMATION Read and follow these information before using the machine. Keep the information safe. Keep your working place orderly. Danger of accident is due to disorder. Protect yourself from electrical shock. Take care of the according instructions. Avoid touching earthed parts, e.g. pipes, radiators, stoves, refrigerators Keep children away. -
Page 10: Storage
25 April 2013 Declaration of conformity We, company Dr. Schulze GmbH declare, that the Floor Milling Cutter DBF 200 and DBF 200-B has been produced under our responsibility and correspond to the regulations of the following European Community guidelines: •... -
Page 11: Exploded View
13. EXPLODED VIEW [10]... - Page 12 [11]...
- Page 13 [12]...
- Page 14 [13]...
- Page 15 [14]...
-
Page 16: Circuit Diagram Dbf 200
14. CIRCUIT DIAGRAM DBF 200 [15]... -
Page 17: Spare Parts List
15. SPARE PARTS LIST Position Description Position Description lid cabinet lifting screw shield of cover belt ring hexagonal shaft hexagonal case regulating nut delimiting ring tensioning screw protective ring shaft pivot screw lever of lifting cover ratchet ratchet lever pivot rod screw pivot rod lifting screw...
Need help?
Do you have a question about the DBF 200 and is the answer not in the manual?
Questions and answers