Advertisement

Operator's Manual
Track Dumper RMD650 / RMD650-B
Do not use this device until you have fully read and
understood these instructions!
28
sales@geargb.co.uk
www.geargb.co.uk

Advertisement

Table of Contents
loading

Summary of Contents for Baumax RMD650

  • Page 1 Operator’s Manual Track Dumper RMD650 / RMD650-B Do not use this device until you have fully read and understood these instructions! sales@geargb.co.uk www.geargb.co.uk...
  • Page 2: Table Of Contents

    15. Maintenance intervals 16. Technical Data 17. Description - Engine 18. Tightening torques 19. Fault finding 20. Exploded diagram Track Dumper RMD650 21. Service record EC Declaration of Conformity ©Technickhandel Echterdingen Ltd., Esslinger Str 7, 70771 Leinfedlen-Echterdingen. All right reserved. E&OE.
  • Page 3: Introduction

    27. Service Record for Model _________ Purchase Date: _________ Thank you for purchasing our product! Date Date This machine should only be used by a competent person who Work carried out Work carried out has read and understood this manual! 1.
  • Page 4: Hazards, Risks & Behaviours

    20. Exploded Diagram Track Dumper RMD650 / RMD650-B Never allow anyone to operate the machine without prior instruction! Make sure that all operators have read and understood the operating instructions and that they act in accordance with the instructions given here! The incorrect and imprudent use of the machine can result in serious injury.
  • Page 5 Make sure that you do not come into contact with the exhaust or other hot parts! Engine losing power Touching these parts can result in serious burns. Air filter dirty Clean / replace air filter Blocked carburettor Clean carburettor and nozzle Only allow the machine to be repaired and adjusted by trained personnel! Defective spark plug Replace spark plug...
  • Page 6: Operator Requirements

    18. Tightening Torques Protective Clothing Tensile Strength 10.9 12.9 Always wear ear protection! Wear goggles and dust mask in dusty environments! Tightening Torque (Nm) Always wear safety shoes and proper protective clothing! Thread Size Wear a Helmet! Other Risks Slips, trips and falls are the main causes of serious or even fatal injuries. Avoid uneven or slippery work surfaces! Avoid working near unprotected holes or trenches! 4.
  • Page 7 This Track Dumper Is Not Suitable For: 17. Description - Engine • Transport of people • Transport of overhanging cargo Filler cap • Transport of liquids Fuel tank Throttle Intended Use Starter handle The operator must be located, and must control the device carefully from, behind the Pull starter unit with hands on the controls during operation.
  • Page 8: Before Starting

    Use only suitable and approved hoists, slings and lifting accessories with sufficient capacity. Use only permissible lifting points according to the instruction manual and Model RMD650 RMD650-B ensure that the machine is secured reliably on the hoist. There must be no persons Operating weight - Unladen (kg) c.
  • Page 9: Start-Up

    Tracks Tensioning Bolts Check the Fuel Level 19. Explosionszeichnung BAUMAX® VP16/44 4. Wenn der Ölstand zu niedrig ist, Motoröl entsprechend dem Kapitel „Technische Daten“ nachfüllen! Open fuel tank and check the fuel level. When refuelling, always use a filter to ensure that no contaminated fuel enters the tank.
  • Page 10 13. Steering and Braking Adjustment Turn the red On / Off switch on the right-hand guide handle to the “ON” position. ATTENTION! For version with Briggs & Stratton 900, also move the red ignition If the Track Dumper does not steer left and right correctly, readjust the steering switch on the engine to the “I”...
  • Page 11 ATTENTION! Operation of the machine with too heavily soiled, defective, or incorrectly seated air filter will cause damage to the engine. Such operation will Set the throttle to half throttle position. void the warranty and guarantee. Pull the starter rope out slowly until a Belt slight resistance is felt;...
  • Page 12: Driving The Track Dumper

    9. Driving the Track Dumper 11. Shut Down Select the desired gear using the shift lever. 1. Set throttle to idle position. If selection is not easy/possible, press and release the clutch lever then try again. 2. Turn the engine ignition switch to the “OFF” position. When the desired gear has been engaged, grip and hold the red clutch lever to start 3.

This manual is also suitable for:

Rmd650-b

Table of Contents