Page 3
Watts Battery, Corp. Additional information is available upon request. The following are registered trademarks All technical specifications described in this of Watts Battery, Corp. in the European Union and other document have been checked for accuracy at countries: the time of printing. However, the policy of Watts...
TABLE OF CONTENTS RECOMMENDATIONS TO THE BUYER.........................4 SAFETY PRECAUTIONS............................7 WHY DO I NEED WATTS?............................8 SPECIFICATIONS..............................10 APPEARANCE AND INDICATIONS OF THE WATTS...................13 EQUIPMENT................................15 CONNECTION AND OPERATION......................18 Quick start...............................19 Setting up an Internet connection........................24 Recommendations for choosing the amount of WATTS, and the relative battery life........26 Installing a stack (multiple WATTS)......................28 The connection of photovoltaic panels......................30 FIX A PROBLEMS...............................30...
Watts Do not immerse WATTS or its components in certified installers. Watts Battery is not water or other fluids. liable for personal injury or property damage caused by repairs or installation undertaken...
Page 6
When using the device outdoors, make sure Batteries in WATTS are not replaceable. that water droplets, dust, dirt, and insects do Contact the Watts Battery Authorized Reseller not get into the device. who sold the WATTS for any repairs. In fire extinction, use a powder fire Do not open the batteries: deformation of the extinguisher only;...
Page 7
or fire alarms. Radio waves can interfere place the module near other devices that with the operation of automatic control use 2.4 GHz signals, such as other wireless equipment, which can lead to accidents due LAN devices, microwave ovens, and remote to equipment failure.
WHY DO I NEED WATTS? Simple renewable energy WATTS is a lithium-ion power storage system that converts solar energy into a daily resource, provides redundancy protection in the event of a power outage. WATTS stores renewable energy, accumulates energy from the network at optimal hours, increases the total volume of electricity production from renewable sources, and independently distributes the optimal power supply to your home.
SPECIFICATIONS OUTPUT POWER INPUT POWER SPECIFICATIONS SPECIFICATIONS 1500 W/2200W Rated power consumption 400 W Rated output/ peak power for 50Hz systems from mains in battery mode output (7 sec.) 1000 W/1500W for 60Hz systems Mains input voltage 230V/50Hz/ (Single Phase) 120V/60Hz Rated power in the mode of transmission of the...
Page 10
SPECIFICATIONS GENERAL COMMUNICATION Weight approx 802.11 b/g/n (depending on 14 kg (30,8 lbs) Protocols (802.11n up to configuration) 150 Mbps) 140 x 460 x 360 mm Dimensions (H x W x D) Frequency Range 2.4~2.5 GHz (5,5 x 18,1 x 14,1 in) Bluetooth version Operating Usage Temp -10 - 40 С...
APPEARANCE AND INDICATIONS OF WATTS Top view 360 mm 14.2 in 1 - Top of the interblock connector, cover of the interblock connector. 2,4 - Outlet covers AC 230/120 volts. 3 - Cover for USB connectors. 5 - Interblock information contacts. Bottom view 6 - Bottom of the interblock connector, cover of the interblock connector.
Page 12
360 mm 14.2 in APPEARANCE AND INDICATIONS OF WATTS Front view 11,15 - Ventilation compartments. 12 - Energoblok start button (Switch on/off). 13 - Charge indication (100/80/60/40/20%). 14 - Multi-function indicator ring (Red-error/ yellow - normal operation/ blue Bluetooth connection/ flashing blue-Bluetooth search mode/ yellow flashing - loading communication devices/ purple-debugging mode) Back view...
Page 13
APPEARANCE AND INDICATIONS OF WATTS Top indicators 21,29 - Screws (black color) 22 - Indicator of the connection to the external power grid. (Power cable / terminal connection / external generator) 23 - Indicator for connecting to the PV supply panels. 24 - Internet connection indicator.
CONNECTION AND OPERATION Quick start Install WATTS in a place you chose, with good STEP 1 ventilation. Do not install WATTS upside down The free space around the or on its side. All supports [10] must touch block (blocks) should be at the surface of the installation site.
Below are the installation steps screens, the app may differ from the latest version. The app is free, but your mobile carrier may charge you extra for downloaded traffic. WATTS Battery (3+) WATTS Battery (3+) download link...
Page 17
CONNECTION AND OPERATION Setting up an Internet connection STEP 3 STEP 4 1. You are now on the main page of WATTS, where 1. In the settings menu, select the WI-FI section. you can view the actual energy distribution model. 2.
Page 18
CONNECTION AND OPERATION Setting up an Internet connection STEP 3 STEP 4 Successful Successful 1. In the window that appears, enter the name 1. Next, in the settings menu, click Connect to the of the Wi-fi network. cloud. 2. Enter the network password, be careful if the 2.
Connection and operation Recommendations for choosing the amount of WATTS, and the relative battery life. Select the number of blocks depending on the power of the connected load and the required time to reserve the power supply. The table shows data that can be used to select the optimal number of WATTS. Amount of energy and possible operation time is strongly affected by environmental conditions and the nature of the load, so the duration of operation may change.
Connection and operation Installing a stack (multiple WATTS) ATTENTION! All work in this section is to be performed by qualified personnel. An untrained person puts himself at risk of injury or death. STEP 1 • Put the installation in a well-ventilated area. •...
Page 21
Connection and operation Installing a stack (multiple WATTS) STEP 3 Remove the top cover [1] from the Master’s • Keep an eye on the interblock connector (first on the ground block) original screws. as in the image, then remove the lower cover [6] from the top block.
Page 22
Connection and operation Installing a stack (multiple WATTS) STEP 5 Place the block on the master block so that all four • Do not Switch supports [10] are in regular contact with the master on WATTS until block body. the installation is complete.
Page 23
Connection and operation Installing a stack (multiple WATTS) STEP 7 • It is not allowed to 4. Determine the length of the cable, taking into account connect the power the padding in the gutter and the distance from the supply through the switchboard.
Page 24
Connection and operation Installing a stack (multiple WATTS) STEP 9 After assembling the electrical circuit, turn on the • Make sure that battery protection switch [20], and press the button all power cables [12] on each block starting from the master. are connected correctly.
Connection and operation The connection of photovoltaic panels ATTENTION! All work in this section is to be performed by qualified personnel. An untrained person puts himself at risk of injury or death. STEP 1 Open the terminal connector [18] (input with •...
Page 26
Connection and operation The connection of photovoltaic panels STEP 3 The minimum permissible cable cross-section in • Ground the photovoltaic panels. this housing is 16 mm2, and the maximum cable connection length is 20 m (65,6 ft). • Observe the polarity of the Prepare the cable: cable lines.
Page 27
SOLVE PROBLEMS A problem Possible reason Necessary actions Short press on the power Press and hold the power button for 5 seconds button again The device does not Connect the device to an energy source (mains, turn on, the solar panels) and wait half an hour while the The battery voltage is battery indicator device is charging.
Page 28
SOLVE PROBLEMS A problem Possible reason Necessary actions Charge the device, to do this, connect the The battery is critically device to an energy source (mains, solar discharged panels) The device emits a continuous beep Turn off the device while holding the power The module is in button for 3 seconds.
TYPICAL CONNECTION SCHEMATICS Standard connection via a household outlet in a house and a housing outlet Connection to the electric power system for automatic switching and backup of electricity Connection to the electric power system for automatic switching and backup of electricity OWNER’S MANUAL - WATTS...
Page 30
TYPICAL CONNECTION SCHEMATICS Hybrid mode of energy reservation and distribution Multi-block mode for maximum autonomy and protection from blackouts OWNER’S MANUAL - WATTS...
WARRANTY CONDITIONS Product Description Smart system for energy storage and power distribution Product type Model WBX 1 Serial number Date of purchase Seller Details Seller name Address Telephone E-mail The device was received in good condition. I have read and agree with the terms of the warranty.
Page 32
Warranty Terms Dear customer! Watts Battery is grateful for your choice and guarantees the high quality and impeccable functioning of this product in compliance with the rules of its operation. Additions to the instruction manual. Upon purchase, we kindly ask you to carefully study the basic operating instructions and check the accuracy of the product description and information about the seller.
Page 33
• Advertising and (or) promotional items (Clothing, wearable electronics, printing products, branded advertising products) Confidential and Personal Information Watts Battery is not responsible for the loss of any confidential or personal information by the user when using the device. Service Periodic maintenance of the product (replacement of batteries, filters, indication lamps, cleaning of internal components, replacement of the housing, etc.) at the initiative of the consumer outside the scope of...
Page 34
Disposal Disposal of old batteries Disposal of an old household and accumulators appliance A symbol on the device showing a crossed- A symbol on the device showing a Wеее Battery out wheeled bin means that the Directive crossed-out wheeled bin means that 2006/96 / CE is applied to the product.