Summary of Contents for Raytum Photonics D-Light-HP200
- Page 1 1 D-Light-HP-200 operation manual D-Light-HP200 High Power Fiber-Coupled Diode Laser Operator’s Manual www.raytum-photonics.com...
- Page 2 Rev. 1.0 This document is copyrighted with all rights reserved. No part of this publication can be copied, stored in a retrieval system, or any other media, including translation into other languages, without prior written permission from Raytum Photonics LLC. www.raytum-photonics.com...
-
Page 3: Table Of Contents
3 D-Light-HP-200 operation manual Table of Contents Preface ………………………………………………………………………………………. Laser Safety …………………………………………………………………………………. 5 Packing and Accessories ……………………………………………………………………. Product General Information ……………………………………………………………….. 3.1 Product Description …………………………………………………………………………… 8 3.2 Product Dimensions …………………………………………………………………………… 9 3.3 Product Specification ……………………………………………………………..…………… 10 Operation Instruction……..…………………………………………………………………. 4.1 Physical Interface………………….. …………………………………………………………. 4.2 D-Light Driver...…………….…………………………………………………………………. -
Page 4: Preface
Photonics customer service. U.S. Export Control Laws Compliance It is the policy of Raytum Photonics to comply strictly with U.S. export control laws. Export and re-export of lasers manufactured by Raytum Photonics are subject to U.S. Export Administration Regulations, which are administered by the Commerce Department. In addition, shipments of certain components are regulated by the State Department under the International Traffic in Arms Regulations. -
Page 5: Laser Safety
5 D-Light-HP-200 operation manual Laser Safety All manufacturers of lasers in the United States must confirm to regulations administrated by the Center for Devices and Radiological Health (CDRH), a branch of the U.S. Department of Health and Human Services. CDRH categorizes lasers as the follows: www.raytum-photonics.com... - Page 6 6 D-Light-HP-200 operation manual The D-light semiconductor laser system emits Class IV radiation. The greatest concern when using a laser is eye safety. Caution must be extremely exercised during operation. The laser will be operated only by those who have had training in laser theory, techniques of control, and operation of the laser(s).
-
Page 7: Packing And Accessories
7 D-Light-HP-200 operation manual Packaging and Accessories Please open the packing carefully and check the items in it as follows: D-Light Laser × l User Manual × l Test Report × l Spare Fuses × 2 Packing List × l Power Cord ×... -
Page 8: Product General Information
3. Product General Information 3.1 Product Description D-light-HP200 fiber coupled diode laser is a complete, turn-key system suitable for material processing, medical therapeutics and pumping solid-state laser media. The system consists of a single enclosure which integrates the laser heads, water coolers and all necessary drive and control electronics. -
Page 9: Product Dimensions
9 D-Light-HP-200 operation manual Product dimensions 550 mm Figure 3.1 D-light diode laser system dimension www.raytum-photonics.com... -
Page 10: Product Specification
10 D-Light-HP-200 operation manual Product Specification Table 3.1 D-light-HP200 Diode Laser Module Specification Specification Parameter Note Optical Parameters Output power >200W Nominal Wavelength 794.7 nm At 200W output power Spectrum width <0.2 nm FHWM Fiber diameter 1200 µm 0.22 Electrical Parameters... -
Page 11: Operation Instruction
11 D-Light-HP-200 operation manual Operation Instruction 4.1 Physical Interface Front Panel details of the front panel are shown below: Emission Emergency Indicator Button Fiber Cable with D80 Connector Laser On/Off • Laser ON/OFF Key Turn on or off the laser. When the laser is on, the Emission Indicator is on. - Page 12 12 D-Light-HP-200 operation manual Back Panel details of the back panel are shown below: Power Supply USB1 USB2 Interlock On/Off Water In Water Out • Power Supply ON/OFF Turn on or off the laser power supply. When the power supply is on, the Red indicator inside the Emergency Button is on.
-
Page 13: D-Light Driver
13 D-Light-HP-200 operation manual The laser will disable until the water flow with minimum 0.3GPM flow rate and right direction. D-Light Driver Installation First of all, make sure the USB driver is included in the shipping package. 1) Install firmware driver Find the file “CDM21228_Setup”... - Page 14 14 D-Light-HP-200 operation manual 3) Copy configure file: copy “Dlight Config” and paste it to “C:\RT” Copy: Paste: Required Connections • AC power Plug the supplied input power cord into the rear of the unit. • Laser Enable Key The key must turn on and make sure the indicator is on. •...
- Page 15 15 D-Light-HP-200 operation manual The D-Light is operated from a host computer, which need to be connected by a standard USB A-A and a USB B-A cable. Both connectors are on the rear of the unit. • Interlock The D-Light interlock is in the rear of the unit as shown in part 4.1. The interlock is a small two-pin connector and must be shorted to allow laser current to flow.
-
Page 16: Operation Procedure
16 D-Light-HP-200 operation manual • Turn on/off Modules The module buttons are disabled when the software is initiated. Users can turn on Module 1 and Module 2 independently or turn on both of them. Each module group provides more than 100W output. - Page 17 17 D-Light-HP-200 operation manual • Turn one the key on the front panel The key has to be in horizontal position to enable the laser. The green indicator showing the key is in on position. • Turn on Laser The laser can be enabled individually by turn on the Module 1&2. The default driving current for each module is 4A, way below the lasing threshold.
-
Page 18: Service And Maintenance
18 D-Light-HP-200 operation manual • Shut down the laser system Click Module 1 & Module 2 to make sure they turn grey green. The driving current should automatically set to 4A. Click “STOP” button. Service and Maintenance The D-light diode laser system is a maintenance-free device. Periodic operation, maintenance, and service of this laser are not required. - Page 19 Fill the RMA form as instructed. Pack the diode laser system in its original package box. Ask Raytum Photonics to provide one in case the original package box is not available. Ship the package to: Raytum Photonics LLC.