Summary of Contents for Sinpo DRO II Series
- Page 1 DIGITAL READOUTS 0peration Manual DR OⅡ Series Ver 1 0 GUIYANG XINTIAN OETECH CO WWW CHFOIC COM...
- Page 2 Dear users Thank you for purchasing our DRO-Ⅱ series digital readouts The digital readout is applicable for the machines such as miller lathes boring machines grinding machines and EDM etc Read all the instructions in the manual carefully before used and strictly follow them Keep the manual for future references...
- Page 3 1 Generral description 1 1 DRO 2M..Ⅱ ..........1 1.2 DRO Ⅱ- ......... 3 DRO Ⅱ- ......... 4 DRO Ⅱ- ........5 DRO Ⅱ- .......... 2 Parameters settings 2 1 Encode type setting ..... . 2 2 Resolution setting ..
- Page 4 4 3 1 SMOOTH R Function ....4 3 2 SIMPLE R Function ....4 4 Chambering 2M 3M Ⅱ- 、 ....4 5 Tool Compensation Function 2M 3M Ⅱ- 、...
- Page 5 1 . 1 D ROⅡ- 2 M Cal CE a b s in c ± s i n c o s t a n DR O -2M Ⅱ i n c h...
- Page 6 DR O -3M Ⅱ Cal CE ± E N T Ⅱ...
- Page 7 1 .4 D R OⅡ- 3 E a rc C al × ÷ ± RI RI DRO -3E Ⅱ I nc...
- Page 8 1 . 4 D ROⅡ-2 L ( 2 L 2 ) ar c Ca l si n × co s ÷ ta n ± T OO L RI RI DROⅡ-2L C AL L I nc 4 )Z + Z 1 F u n c t i o n( 2 L 2 )
- Page 9 1. 5 DR OⅡ- si n × c o s ab s ÷ ta n I n c ± DROⅡ- R I R I SIFT...
- Page 10 Note:If this parameter is input by positive number, the display window will display by centigrade.If this parameter is input by Negative number, The display window will display by degree/minute/second. )
- Page 11 Step 5 Set decimal digits under inch system(usually set 4 digits) INC H DOT I NC H DO T Press the key to access the system setting.
- Page 12 1 . 00 00 0 2 . 0 0 00 0 3. 00 0 0 0 1. 0 0 00 0 2. 0 0 00 0 3. 00 00 0...
- Page 19 E N T...
- Page 28 XY p l a ne R...
- Page 32 E N T...
- Page 33 XY p l a ne R...
- Page 35 c o s c o s...
- Page 36 t a n t a n t a n...
- Page 37 s i n s i n...
- Page 38 s i n E N T 1 0. 00 0 D IA Cal CE ± S i n t a n t a n C OS C OS E N T 0 .00 0 ST P OS Cal CE 0. 000 -2 0.0 00 ±...
- Page 39 Cal CE ± E NT si n...
- Page 40 SIFT SIFT SIFT SIFT...
- Page 42 T OO L T O O L E N T T O O L T OO L T OO L E NT T O O L...
- Page 44 4.9 4 About the DRO -2L2 Ⅱ DRO -2L2 is a 3 axis digital readout specially used on lathe machines. Ⅱ It is the same as that of DRO Ⅱ -2L except that it adds a linear scale (Z1) to measure the position of the machine working stage.
- Page 47 E N T E N T E N T...
- Page 48 E N T...
- Page 50 1 Supply Voltage AC100V 240V 50HZ 60HZ 15VA 2 Power consumption 3 Operation temperature 0 45 4 Storage temperature ℃- ℃ 5 Relative humidity : < ％( 6 Max coordinate number 7 Readout allowable input signal TTL square wave 8 Allowable input signal frequency 600kHz <...
- Page 52 Service GUIYANG XINTIAN OETECH CO Tel 86 0851 6452262 Fax 86 0851 6453885 : / / Website http www chfoic com E mail shuxian chfoic com...
Need help?
Do you have a question about the DRO II Series and is the answer not in the manual?
Questions and answers