1. Manuals
  2. Brands
  3. Moore Unidrill Manuals
  4. Farm Equipment
  5. 300G
  6. Instruction book

Moore Unidrill 300G Instruction Book

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
MOORE UNIDRILL 300G
Foreword
Please read and observe these instructions very carefully before you proceed to operate the seed
will
drill. In this way you
reliability and service life of your seed drill. Pay particular attention to the safety instructions! Moore
Unidrill Ltd cannot assume any liability for damage or malfunctions caused by a failure to observe
the instructions contained in this operating manual.
The purpose of this operating manual is to enable you to familiarize your self with the working of
your seed drill and to make full use of the many possibilities of application which it affords. The
manual will first of all explain the seed drill
features of the different models. The chapters entitled "Additional Accessories", "Care and
Maintenance" and 'Troubleshooting" apply to
The terms "right", 'left", "front" and "back" are used here for when sitting in the tractor seat looking
forward.
This operating manual must be read and used by all persons who are required to carry out work
either on or with the seed drill, e.g.,
• Operation
• Maintenance
• Transporting.
Enclosed with this operating manual is a registration card. Once you have familliarised yourself with
the drills operation, please return the registration card to Moore Unidrill Ltd. This will confirm your
acquisition of the seed drill. The period of guarantee commences on the date of of delivery.
Moore Unidrill Ltd reserve the right to make changes to the illustrations and data on specifications
and weights contained in this operating manual if we make any improvements to the seed drills.
This instruction manual is to be read in conjunction with the Kverneland Accord Operating manual,
also supplied.
Seed drill identification.
Once you have accepted delivery of the seed drill, please enter the following data:
.............................
Serial No.:
..................
Seed drill model:
....................
Working width:
Number of coulters:
................
P.T.O. shaft speed:
........................
Accessories:
.......................................
....................................
Date of issue of Operating Manual: March 2011
MOORE UNIDRILL LTD
33,KIRK ROAD
BALLYMONEY,
Co.ANTRIM,
NORTHERN IRELAND BT53 6PP
Tel. +44(0)28 2766 44444
www.moore-unidrill.com
sammy@moore-unidrill.com
avoid accidents, reduce repair costs and downtimes and increase the
..................
in
general and then proceed to describe the special
seed drill models.
all
August 2016 S/N 8314-

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 300G and is the answer not in the manual?

Questions and answers

Summary of Contents for Moore Unidrill 300G

  • Page 1 Enclosed with this operating manual is a registration card. Once you have familliarised yourself with the drills operation, please return the registration card to Moore Unidrill Ltd. This will confirm your acquisition of the seed drill. The period of guarantee commences on the date of of delivery.
  • Page 2 2. Guarantee claims must be submitted on special Moore Unidrill Ltd claim forms to Moore Unidrill Ltd product support, at Ballymoney. Claims cannot be considered unless the claim form has...

  • Page 3: Proper Use

    Moore Unidrill cannot be held liable for damage or injury caused by the use of non-OEM replacement parts or accessories.

  • Page 4: Road Safety

    August 2016 S/N 8314- No liability for consequential damage Even though your Moore Unidrill seed drill has been manufactured with the utmost care and you are using it properly, fluctuations and interruptions in seed delivery may still occur, the possible causes being: •...

  • Page 5: Accident Prevention

    MOORE UNIDRILL 300G August 2016 S/N 8314- Accident prevention Careful heed must be paid not only to the safety instructions contained in this operating manual but also to 'the accident prevention regulations governing the operation of agricultural machinery. You could injure yourself on those edges of the seed drill which need to be sharp.
  • Page 6 MOORE UNIDRILL 300G August 2016 S/N 8314- In order to exclude the possibility of incorrect connection, all mating plugs and sockets belonging to the hydraulic connections between the tractor and the seed drill should be marked with matching colours. When operating the seed drill Prior to start-up and operation, make sure that nobody is standing in dangerous proximity to the seed drill (especially children).
  • Page 7 MOORE UNIDRILL 300G August 2016 S/N 8314- Description and technical detail. The Moore Grassland Unidrill uses a Kverneland Accord DE/S hopper, and full operating details, parts lists, and other CE information is included within the attached instruction books pertaining to that product.
  • Page 8 • Heavy Duty 100mm x 100mm x 10mm Powder coated chassis. • Low maintenance trailing arm rubber suspension, offset to achieve close row spacing. • Proven MOORE UNIDRILL sowing disc/coulter arrangement 410 mm x 5 mm serrated boron discs • LONG LIFE Tungsten carbide tipped coulters •...

  • Page 9: Road Transport

    MOORE UNIDRILL 300G August 2016 S/N 8314- Setting and using the seed drill Road transport Fit warning signs and the necessary lighting and guards for road transport. Make sure the seed hopper is empty before you proceed to transport your seed drill along the road.
  • Page 10 MOORE UNIDRILL 300G August 2016 S/N 8314- the shaft, cut the PTO drive shaft guard to size at both ends and then de-burr, clean and grease the protective tubes and the special section tubes. After it has been adapted fit the universal joint shaft.

  • Page 11: Care And Maintenance

    MOORE UNIDRILL 300G August 2016 S/N 8314- This is done by adjusting the pin and hole arrangement for raising/lowering the rear Guttler packer roll height in relation to the main chassis. The rear packer acts as a depth stop, and can increase and decrease the amount of pressure on the rubber units.

  • Page 12: Spare Parts

    MOORE UNIDRILL 300G August 2016 S/N 8314- Guttler roll main bearings (1 on each end, and 2 back to back in the middle) should be greased every 20 hours of work, and before each seasons storage. Nuts and bolts All nuts and bolts should be checked regularly. When working in stoney or trashy conditions it will be necessary to check all nuts and bolts daily, particularly the seed tube coulters and disc bolts.
  • Page 13 MOORE UNIDRILL 300G August 2016 S/N 8314- Guttler roller 1. 75517000 ucf 40mm bearing 2. 75408000 45cm special end guttler 3. GUT2 guttler scraper holder 4. GUT3 guttler hardox scraper 5. 75407000 50cm guttler 6. 75406000 45cm guttler 7. 70403005 1472mm shaft to fit 40mm...
  • Page 14 MOORE UNIDRILL 300G August 2016 S/N 8314- Complete parts list total including weights of common serviceable components. Material Description HUT1001PLH/PRH left and right suspension units PEER Hub Bearing 600006 410 mm x 5mm serrated Disc 5 hole peer 20LH / 20089RH...
  • Page 15 MOORE UNIDRILL 300G August 2016 S/N 8314- 140010 m16 x 70 bolt 140012 m16 x 55 bolt 140017 m16 nyloc 140065 1 1/4 x 7 1/2 unc bolt 3" 140062 1 1/4 nyloc 140096 m10 x 35 140041 m10 nyloc...
  • Page 16 August 2016 S/N 8314- Techniques The Moore unidrill prepares its own mini seedbed by using an angled disc and seed tube coulter tine. All seeds are planted at a constant depth, The points of the guttler roller slit the ground 305 times per square meter, to give good seed soil contact, however in some conditions another pass with a flat roll is necessary.
  • Page 17 A light to medium coat of slurry immediately after seeding (depending on moisture) can be applied providing it contains no effluent or dairy washings. Moore Unidrill cannot be held accountable for off label use of chemicals Method 4 Early Spring drilling...
  • Page 18 MOORE UNIDRILL 300G August 2016 S/N 8314- After silage We prefer to cut the silage first rather than apply glyphosate pre harvest, at the recommended 5 days, as this prevents any wheelings from the sprayer appearing in subsequent crop, also Glyphosate seems more effective on less volume of grass. By delaying drilling up to a week after cutting, regrowth will have started, and then drill, and delay spray application up to another week, at least before the new seed germinates.
  • Page 19 MOORE UNIDRILL 300G August 2016 S/N 8314- There is no doubt that a blend of 50% perennial Hybrid Tet, 25% Intermediate tet and 25% diploid works best. These are mostly larger seeds with greater energy reserves for coping with adverse situations.Italian ryegrass swards can easily be re-established at the end of their allotted...
  • Page 20 MOORE UNIDRILL 300G August 2016 S/N 8314- Original Instructions MOORE UNIDRILL LTD 33, KIRK ROAD, BALLYMONEY, Co.ANTRIM, NORTHERN IRELAND. BT53 6PP PHONE +44 (0) 2827 66 44444 email sammy@moore-unidrill.com www.moore-unidrill.com...

  • Page 21: Eu Declaration Of Conformity

    MOORE UNIDRILL 300G August 2016 S/N 8314- EU DECLARATION OF CONFORMITY Declaration No. 300G1 We, the undersigned Moore Unidrill Ltd
 33 Kirk Road, Ballymoney
 County Antrim, Northern Ireland.
 BT53 6PP Declare under our sole responsibility that the following apparatus: Name: MOORE UNI DRILL...

Table of Contents