Square 1 Design TR210-14 Operator's Manual

Roof truss finish roller

Hide thumbs

Table Of Contents

Table of Contents

Quick Links

Download this manual

FOREWORD

This manual explains the proper maintenance of Square 1 Design Finish Rollers, as well as the daily

lubrication and periodic inspection procedures. Please read this manual thoroughly even though you

may already be familiar with other Square 1 Design Finish Rollers, because this manual contains the

most current information about Square 1 Design Finish Rollers. This manual has been based on the

standard Square 1 Design Finish Roller. If you have any questions on modifications to your equipment,

please contact Square 1 Design & Manufacture, Inc., or your sales representative. Square 1 Design &

Manufacture, Inc. reserves the right to make any changes or modifications to this manual or Square 1

Design Finish Rollers without giving previous notice and without incurring any obligation.

SQ-1 ROOF TRUSS FINISH

FOREWORD

This manual explains the proper maintenance of Square 1 Design Roof Truss Finish Roller as well as

the daily lubrication and periodic inspection procedures. Please read this manual thoroughly even

though you may already be familiar with other Square 1 Design equipment, because it contains the most

current information about the Square 1 Design Truss Roller. This manual has been based on the

ROLLER

Operators Manual

Roof Truss

Roller

TR210-14

TR212-14

TR214-14

TR215-14

TR216-14

Table of Contents

Need help?

Do you have a question about the TR210-14 and is the answer not in the manual?

Questions and answers

Summary of Contents for Square 1 Design TR210-14

Page 1 FOREWORD This manual explains the proper maintenance of Square 1 Design Finish Rollers, as well as the daily lubrication and periodic inspection procedures. Please read this manual thoroughly even though you may already be familiar with other Square 1 Design Finish Rollers, because this manual contains the most current information about Square 1 Design Finish Rollers.
Page 2: Foreword
ALWAYS DISCONNECT AND LOCK OUT ANY POWER SOURCES WHEN ADUSTING OR REPAIRING ANY EQUIPMENT. FOREWORD This manual explains the proper maintenance of Square 1 Design Roof Truss Finish Roller as well as the daily lubrication and periodic inspection procedures. Please read this manual thoroughly even though you may already be familiar with other Square 1 Design equipment, because it contains the most current information about the Square 1 Design Roof Truss Finish Roller.
Page 3: Table Of Contents
ALWAYS DISCONNECT AND LOCK OUT ANY POWER SOURCES WHEN ADUSTING OR REPAIRING ANY EQUIPMENT. CONTENTS Foreword Page 1 Before Initial Operation Page 3 General Description Page 4 Operation of Roof Truss Finish Roller Page 5 Safety and Maintenance Page 5 Safety Guidelines Page 6 Safety Checklist...
Page 4: Before Initial Operation
1 Design Roof Truss Finish Roller and permit you to operate it correctly and safely. • Identify and inform ALL employees who will operate or be near the Square 1 Design equipment of ALL safety concerns in this manual and on the production floor.
Page 5: General Description
The model # and serial #’s are located on the Inside of the Electrical Panel of the Square 1 Design Finish Roller. This information will be needed when contacting Square 1 Design & Manufacture Inc. for service information.
Page 6: Operation Of Roof Truss Finish Roller
ALWAYS DISCONNECT AND LOCK OUT ANY POWER SOURCES WHEN ADUSTING OR REPAIRING ANY EQUIPMENT. OPERATION OF THE ROOF TRUSS FINISH ROLLER The Square 1 Design Roof Truss Finish Roller is very simple to operate and maintain. Square 1 Design suggests that operation of the Square 1 Design equipment proceed in the following manner: 1.
Page 7: Safety Guidelines
Safety glasses must be worn for the protection of the employees. Employees without the proper equipment should not be allowed near the Square 1 Design Roof Truss Finish Roller. It is management’s responsibility to enforce these guidelines. It also becomes the employee’s responsibility to make sure these guidelines are enforced.
Page 8: Safety Checklist
D. Check the area surrounding the Square 1 Design Roof Truss Finish Roller for cleanliness. E. Perform daily maintenance F. Be sure area is clear of people when starting the machine. G. Check to be sure everyone around the Square 1 Design Roof Truss Finish Roller is wearing the proper equipment. Weekly: A.
Page 9: Maintenance
Maintenance on the Square 1 Design Roof Truss Finish Roller consists of lubricating the machine and chain and tightening all nuts and bolts. The following maintenance schedule MUST be followed.
Page 10: General Operation
All models of the Square 1 Design Roof Truss Finish Rollers have a drive train on both ends. All rollers are pre-set at Square 1 Design for a standard 2 x 4, and chain tension is pre-set. You may want to feel the tension in the chain when it arrives, so you know the correct tension of the chain.
Page 11: Roller Adjustment
ROLLER ADJUSTMENT The Square 1 Design Roof Truss Finish Rollers have up to 4 1/2” of total roller adjustment. The top roller is the only adjustable roller. The bottom roller remains stationary and is set at 32” high from the floor, unless ordered otherwise.
Page 12: Repair And Replacement
In the case that a part of the machine is not working properly, this section lists how to remove and replace the correct part from the Square 1 Design Roof Truss Finish Roller. If parts are needed it is recommended that you contact Square 1 Design & Manufacture, Inc. at the address list on page 17.
Page 13: Control Panel
ALWAYS DISCONNECT AND LOCK OUT ANY POWER SOURCES WHEN ADUSTING OR REPAIRING ANY EQUIPMENT. CONTROL PANEL This unit is available as a complete control panel, a starter, or component parts for starters. For a parts list, breakout, and schematic to determine the information needed. REMOVAL ON THE CONTROL PANEL •...
Page 14: Motors
MECHANICAL The following section covers the mechanical portion of the Square 1 Design Roof Truss Finish Roller. Exhibits listed throughout this section contain parts lists and breakouts of common replacement parts.
Page 15: Chain Removal
ALWAYS DISCONNECT AND LOCK OUT ANY POWER SOURCES WHEN ADUSTING OR REPAIRING ANY EQUIPMENT. CHAIN REMOVAL • Remove the chain guard by removing the fasteners. • Locate the master link in the chain making sure it is in a location with easy access. Reduce the tension on the chain.
Page 16: Idler Sprocket Removal
ALWAYS DISCONNECT AND LOCK OUT ANY POWER SOURCES WHEN ADUSTING OR REPAIRING ANY EQUIPMENT. IDLE SPROCKET REMOVAL • Remove the chain guard by removing the fasteners. • Remove the chain from the drive train and disconnect the grease tube fittings. Slide the sprocket bracket down to remove it from the mounting channel.
Page 17: Top Roller Removal
ALWAYS DISCONNECT AND LOCK OUT ANY POWER SOURCES WHEN ADUSTING OR REPAIRING ANY EQUIPMENT. TOP ROLLER REMOVAL • Follow the directions to remove the bearing blocks. • Grind off weld tacks holding side frame panels to the top frame supports. Grind side supports from head assembly.
Page 18: Ordering Replacement Parts
SQUARE 1 DESIGN & MANUFACTURE, INC. 1 Clark Road Shelbyville, IN 46176 Phone: +1-866-647-7771 Fax: +1-866-646-5771 sales@square1design.com When ordering parts, you must include the part number of the replacement part and the serial and model #’s of your Square 1 Design Roof Truss Finish Roller.
Page 19: Warranty Information
This is provided the equipment had been properly installed, operated, used, cared for, adjusted, cleaned and lubricated by the owner. All equipment claimed to be defective shall be returned to Square 1 Design & Manufacture, Inc. charges prepaid. All collect shipments will be refused. If upon inspection Square 1 Design &...
Page 20: Detail N: Non-Panel Side
ALWAYS DISCONNECT AND LOCK OUT ANY POWER SOURCES WHEN ADUSTING OR REPAIRING ANY EQUIPMENT. Non-Panel Side...
Page 21: Detail M: Panel Side
ALWAYS DISCONNECT AND LOCK OUT ANY POWER SOURCES WHEN ADUSTING OR REPAIRING ANY EQUIPMENT. Panel Side...
Page 22: Detail K & L: Idler Assembly Both Sides
ALWAYS DISCONNECT AND LOCK OUT ANY POWER SOURCES WHEN ADUSTING OR REPAIRING ANY EQUIPMENT. Panel Side Non-Panel Side...
Page 23: Replacement Parts List
ALWAYS DISCONNECT AND LOCK OUT ANY POWER SOURCES WHEN ADUSTING OR REPAIRING ANY EQUIPMENT. Replacement Parts List for SQ-1 Roof Truss Finish Roller Part Number Description Location SPRO-0011 Drive Sprocket Detail N; Number 53 SPRO-0018 Roll Sprocket Detail N & M; Number 31 SPRO-0017 Taper Lock Bushing on Drive Detail N &...

This manual is also suitable for:

Tr212-14 Tr214-14 Tr215-14 Tr216-14