Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for PLASTEC VENTILATION PSS Series
Summary of Contents for PLASTEC VENTILATION PSS Series
- Page 1 Installation, Operation and Maintenance Manual September 2020...
-
Page 2: Table Of Contents
LASTEC TILITY AND TORM LOWER ................... 8 LLUSTRATION TTACHMENT OF LASTEC AN TO EATHER PLASTEC PSS SERIES STAINLESS STEEL UTILITY BLOWERS ..................... 9 ............................... 9 ISASSEMBLY NSTRUCTIONS ..............................9 EASSEMBLY INSTRUCTIONS : PSS S – PSS20 PSS35 ......................... 10 LLUSTRATION ERIES PLASTEC JET SERIES .............................. -
Page 3: General Instructions
Manufacture or any of Manufacture's employees, agents or contractors. No claims, representations or warranties, whether expressed or implied, are made by Plastec Ventilation Inc as to the safety, reliability, durability, and performance of any of our companies' products. Furthermore, our company accepts no liability whatsoever for the safety, reliability, durability, and performance of any of our companies' products. -
Page 4: Installation
Plastec Ventilation Inc. Installation, Operation & Maintenance Manual September 2020 For equipment stored for extended periods of time (1 month), rotate motor bearings. Records of stored equipment should be kept to assure proper procedures. 1.2 Installation Area where fan is installed should provide support for rigid mounting of the fan(s). Fans not supported properly... -
Page 5: Maintenance
Plastec Ventilation Inc. Installation, Operation & Maintenance Manual September 2020 When power is applied to the unit, check for proper rotation of fan wheel/impeller. Most motors allow for reverse rotation and if the fan wheel/impeller is moving in the wrong direction, air performance will be greatly affected. -
Page 6: Warranty
Plastec Ventilation Inc. Installation, Operation & Maintenance Manual September 2020 Repair or replacement of motors is normally performed by a repair station authorized by the manufacturer. Contact your representative or the factory for locations nearest you. DO NOT ship motor to factory without specific authorization forms. -
Page 7: Plastec Utility And Storm Blowers
Plastec Ventilation Inc. Installation, Operation & Maintenance Manual September 2020 Users and installers of this equipment should read, “RECOMMENDED SAFETY PRACTICES FOR AIR MOVING DEVICES” which is published by Air Movement and Control Association, 30 West University Drive, Arlington Heights, Illinois, 60004. -
Page 8: Illustration: Plastec Utility And Storm Blower
Plastec Ventilation Inc. Installation, Operation & Maintenance Manual September 2020 2.3 Illustration: Plastec Utility and Storm Blower www.plastecventilation.com | +1 (941) 751-7596 page 7... -
Page 9: Illustration: Attachment Of Plastec Fan To Weather Hood
Plastec Ventilation Inc. Installation, Operation & Maintenance Manual September 2020 2.4 Illustration: Attachment of Plastec Fan to Weather Hood 1. The motor feet should point vertically upwards for attachment to the underside of the hood top. Ensure that the fan discharge is correctly orientated in relation to the motor feet. -
Page 10: Plastec Pss Series Stainless Steel Utility Blowers
Plastec Ventilation Inc. Installation, Operation & Maintenance Manual September 2020 3 Plastec PSS Series Stainless Steel Utility Blowers 3.1 Disassembly Instructions Before beginning these instructions, place this fan on a bench or table top that can support its weight. For tool size see illustration. -
Page 11: Illustration: Pss Series - Pss20 And Pss35
Plastec Ventilation Inc. Installation, Operation & Maintenance Manual September 2020 3.3 Illustration: PSS Series – PSS20 and PSS35 www.plastecventilation.com | +1 (941) 751-7596 page 10... -
Page 12: Plastec Jet Series
Plastec Ventilation Inc. Installation, Operation & Maintenance Manual September 2020 4 Plastec Jet Series 4.1 Disassembly Instructions Before beginning these instructions, place this fan on a bench or table top that can support its weight. 1. Disconnect the fan from its power source. -
Page 13: Illustration: Jet Series
Plastec Ventilation Inc. Installation, Operation & Maintenance Manual September 2020 4.3 Illustration: Jet Series www.plastecventilation.com | +1 (941) 751-7596 page 12... -
Page 14: Roof Unit Kits
Plastec Ventilation Inc. Installation, Operation & Maintenance Manual September 2020 5 Roof Unit Kits 5.1 Roof Unit 15 – Roof Unit 30 Kit Assembly 1. Components of Roof Kit: Roof Curb Cap, Motor Cap, Cap Bracket, Exhaust Guard 2. Place the cap bracket on the 3. - Page 15 Plastec Ventilation Inc. Installation, Operation & Maintenance Manual September 2020 11. Screw the roof curb cap to the 10. Place the roof curb cap on the 12. Turn over the housing. housing. housing. Reinforce the base before placing the roof curb cap to support.
- Page 16 Plastec Ventilation Inc. Installation, Operation & Maintenance Manual September 2020 19. Screw back on the terminal box lid. 20-21. Place the motor cap and secure with screws. 22-24. Attach switch with screws on the flat side of the motor cap.
-
Page 17: Roof Unit 35 Kit Assembly
Plastec Ventilation Inc. Installation, Operation & Maintenance Manual September 2020 5.2 Roof Unit 35 Kit Assembly www.plastecventilation.com | +1 (941) 751-7596 page 16... -
Page 18: Electrical Wiring
CAUTION! Proper grounds, disconnecting devices and other safety devices and their location are the responsibility of the user and are not provided by Plastec Ventilation Inc. WARNING! For equipment protection, install a ground leakage type breaker with a fast response circuit capable of handling large currents.
Need help?
Do you have a question about the PSS Series and is the answer not in the manual?
Questions and answers