JE-Gauge Daemon III Operation Manual

Gauge Contents : Gauge*1 / Temp Sensor*1 / Sensor Wire(2pin)*1 / Gauge Wire (6pin)*1 / Gauge Stand*1 / Operation Manual*1 /
Installation Diagram
Suggestions Before Installation
1. Cut the radiator hose to fit the length of water adaptor.
2. Install the Temp. Sensor to water adaptor first.
Ignition Switch Diagram
Accessory
A/C
Ignition-Coil
Motor Starter
Battery
WARNING
1. Please must follow all installations in this manual to ensure safe installation and operation of the product.
2. DO NOT disassemble or reassemble the product. This might cause damage or make them unsafe to use.
When the product is disassembled or reassembled, the Warranty can't be offered.
3. Before installation, please make sure the engine is switched off and the vehicle is stationary.
4. Due to possible injury from contact with a hot engine or exhaust pipe, DO NOT begin installation until the vehicle is cool.
5. When attaching wires for the product, please take care so that the product's wires do not interfere with existing wires.
6. This product is only for use on vehicles with 12V electronic system.
Remote Controller Operation Manual
1. Please have the remote controller point to the gauge you are going to set up.
2. In setting process, press directly; the gauge will leave setting mode and save.
3. A "beep" sound will be heard while the new setting is done.
1.
Water Temp
2.
Oil Temp
3.
A/F
Oil Pressure
4.
Exhaust Temp
VAC RPM
5.
BOOST
WARNING
Please must follow all installations in this manual to ensure safe installation and operation
of the product. DO NOT disassemble or reassemble the product. This might cause damage
or make them unsafe to use. When the product is disassembled or reassembled, the
Warranty can't be offered. Before installation, please make sure the engine is switched off
and the vehicle is stationary. Due to possible injury from contact with a hot engine or
exhaust pipe, DO NOT begin installation until the vehicle is cool. When attaching wires for
the product, please take care so that the product's wires do not interfere with existing
wires. This product is only for use on vehicles with 12V electronic system.
Daemon III
Water Temp. Operation Manual
Gauge
Gauge Wire
To avoid damage, please ensure the RED wire is attached to the ignition switch that connected to Coil.
11.
6.
Warning
A/F Air/Fuel Ratio
7. 12.
Voltage Backlight
13.
8.
DOWN
Vacuum
VAC
14.
9.
Enter
RPM
RPM
10. 15.
Function UP
-
YELLOW: Dimmer 12V
BLACK: Ground
Sensor Wire
RED: Ignition-Coil
CAUTION
1. To avoid water leaks during installation of the sensor, please use Telfon tape while installation.
2. To avoid water leaks, please ensure the size of water adaptor is suited.
3. To avoid damage, please make sure using insulating tape or bushing while connection.
4. To avoid damage of sensor wire, please fix the waterproof connector on the vehicle body.
5. Coolant spills by the installation work. Please replenish the engine with coolant and bleed the air from the system,
or, the engine might overheat.
Backlight LED Setting Function
1.
Select icon by press to enter Water Temp Setting Mode.
2.
Then Press to change the backlight. Press
any button for 5 seconds to leave the setting mode.
Warning Setting When the WT value is Over, the warning will be functional (
1. Select icon by press to enter Water Temp Setup Mode.
2. Press to show Water Temp Warning Value. Then Press
3. Press to save or idle any button for 5 seconds to leave the setting mode.
Peak Value Show / Clear Setting Function
1. Select icon by press to enter Water Temp Setup Mode. Press
2. Press to show Water temp Peak Value. Then press
3. Press to save or idle any button for 5 seconds to leave the setting mode.
Meter Visor*1 Optional ( )
Light (12V)
Temp Sensor
to save the setting or idle
)
or to change the setting.
to Enter Peak Setup Mode.
to clear the Peak Value.
Made&Design in Taiwan