Advertisement
Advertisement
Summary of Contents for Huyosen CG520M
- Page 1 OPERATOR’S MANUAL...
-
Page 2: Table Of Contents
Do not use the product for other tasks than grass trimming and grass clearing. Work is constantly in progress to increase your safety and efficiency during operation. Speak to Huyosen Note: National or local regulations may regulate the use. service for more information. - Page 3 Tools bag Tools Bag Allen Key Spacer Catcher Wrench Hex Wrench Screwdriver Symbols on the product Be careful and use the product correctly. Maximum speed of the output shaft. This product can cause serious injury or death to the operator or others. Read the operator's manual carefully and Keep a minimum of 15 m distance to make sure that you understand the...
-
Page 4: Safety
Contact attachment. However, do not the product unless you Huyosen service . Avoid all usage which you consider are able to call for help in the event of an accident. to be beyond your capability . - Page 5 Personal protective equipment • Keep a good balance and a firm foothold at all times. Do not overreach. • Always hold the product with both hands. Hold the WARNING: Read the warning instructions product on the right side of your body. that follow before you use the product.
- Page 6 WARNING: Never use a product with defective safety components. The product's safety equipment must be inspected and maintained as described in this section. If your product fails any of these checks, contact Huyosen service to get it repaired.
- Page 7 prevents injuries that occur if you touch the cutting 4. Do a check of the throttle control and throttle trigger attachment. lockout move freely and that the return springs work properly. 1. Do a visual check for damages, for example cracks. 5.
- Page 8 To do a check of the muffler WARNING: Bear in mind that the exhaust • Never start the product if the product is leaking fuel. fumes from the engine are hot and may Check regularly for leaks from the fuel cap and fuel contain sparks which can start a fire.
-
Page 9: Assembly
Assembly Introduction 2. Remove the screw E on the shaft . WARNING: Before you assemble the product, you must read and understand the safety chapter. To assemble the U handle 1. Remove the Handle Adjustment screws. 3. Install the spacer and attachment guard on the shaft. 2.Install the u handle . - Page 10 To assemble the 3T blade head 6. Remove the shaft nuts clockwise by Hex wrench. Remove the nuts cover and washer . Hold the allen key turn the nuts anti-clockwies Drive disc Blade head Cover Nuts Washer Drive disc Washer Cover Nuts To assemble the two-piece shaft...
- Page 11 4. Carefully push the shaft(A) into the coupling until you Make sure you back looks like this . hear a click. 5. Push the coupling down and tighten the knob fully . 5. Make sure the shoulder strap soft side is down . To wear the harness 1.
- Page 12 2. Loosen the hook screw and move it to the best position 8. Closed the buckle. 9. Adjust the rope to the best condition Hook screw 3. Maintain balance and reduce burden on hands. 3. Emergency Release To attaching the harness Pull the red tag (G) the buckle will breaks away .
-
Page 13: Operation
Operation Fuel CAUTION: Do not use oil for four-stroke engines. This product has a two-stroke engine. CAUTION: Incorrect type of fuel can result in engine damage. Use a mixture of gasoline To mix gasoline and two-stroke oil and two-stroke oil. Gasoline, liter Two-stroke oil, Gasoline... - Page 14 To fill the fuel tank To start a cold engine 1. Push the switch button up open the engine . 1. Clean the area around the fuel tank cap. 2. Shake the container and make sure that the fuel is fully mixed.
- Page 15 To start a warm engine 6. Pull the starter rope again until the engine start . 1. Push the switch button up. If the engine won’t start please back to step 2 . 2. Push the air primer bulb 6-10 times . CAUTION: Do not pull the starter rope all the way out and do not let go off...
- Page 16 About the surface To cut the grass WARNING: Do not touch the area that is 1. Make sure that the trimmer line is parallel to the identified with gray in the illustration. There ground when you cut the grass. is a risk of burn injuries when the product is hot.
-
Page 17: Maintenance
Do a check of the bevel gear to make sure that it is filled ¾ with grease. Fill the bevel gear with Huyosen special grease if it is necessary. Clean or replace the spark arrestor mesh on the muffler (only applies to mufflers without a catalytic converter). - Page 18 • Starting problems. not stop when you adjust the idle speed, • Loss of engine power. Speak to Huyosen service . Do not • Unnecessary wear to engine parts. use the product until it is correctly adjusted • Too much fuel consumption.
-
Page 19: Technical Data
Spool for grass trimmer line HYP/PA Engine idling speed 25:1... -
Page 20: Troubleshooting
Troubleshooting The engine does not start Check Possible cause Procedure Stop switch. The stop switch is in the stop position. Set the stop switch to the start position. Starter pawls. The starter pawls cannot move freely. Remove the starter cover and clean around the starter pawls. - Page 21 20" 10" 15CM “Click” 6"...
Need help?
Do you have a question about the CG520M and is the answer not in the manual?
Questions and answers