Download Print this page
A&S CRAFTED PRODUCTS BAND ROOM BRUS30 Assembly Instructions

A&S CRAFTED PRODUCTS BAND ROOM BRUS30 Assembly Instructions

Soprano ukulele rack

Advertisement

Quick Links

BRUS30/BRUS18
TM
BAND ROOM
SOPRANO UKULELE RACK ASSEMBLY INSTRUCTIONS
CONTENTS
The Ukulele Rack ships in 2 cartons*:
• One contains 2 sides
• One contains 2 round stickers, 2 black rings,
12 wood rails, 2 handles, felt*, dowels & vinyl sleeves**,
these instructions, and the following hardware:
8 Short
Hex Screws
2 hex
25 Long
wrenches
Hex Screws
* FELT
• BRUS30: 8 strips & 30 pieces
• BRUS18: 4 strips & 18 pieces
** DOWELS & VINYL SLEEVES
• BRUM30: 61 dowels
64 vinyl sleeves (16 of each color)
• BRUM18: 37 dowels
40 vinyl sleeves (10 of each color)
1. Stand the 2 sides up vertically, with the rail recesses facing each other. They should be a little
farther apart than the length of the rails. You might find it easier to stand them up on their sides
as shown in Figure 1. It might also be helpful to lean each side against a chair to keep it upright.
2. Place the rails loosely in position by inserting a long hex screw through the holes in the sides
and into the holes in the ends of the rails. This will establish the rail positions and support both ends of the rails at this point.
Rail #1
Rail #2
Rail #5
Rail #3
Rail #4
Rail #5
Fig. 2A
4 Wheel
Brackets
8 Nuts
4 Wheels
25 Barrel
Nuts
Strips
A. Refer to Figure 2A for placement of the rails.
B. Refer to Figure 2B to note the long and short ends of 3 of the rails (#1, #2 and #4). The long
ends of the rails should be to the right, with the peg holes toward the top of the rail. This is
true no matter which side of the rack you are looking at. They should all be the same; otherwise,
the ukes on the top level will hit each other). Rails #3 and #5 are symmetrical, so it doesn't
matter how you place them.
C. When placing the rails #1, insert the handles into the recesses on the
outside faces of the sides before inserting the screws. (Figure 2C)
SHORT ENDS
ASCraftedProducts.com
2 Sides
2 x
Pieces
2 x
2 x
2 x
4 x
LONG ENDS
Fig. 2B
267-626-6123
2 Handles
2 Stickers
12 Rails
Fig. 1
Rail #1
Rail #2
Rail #4
Fig. 2C
BRUS30/BRUS18 0517
©2017 A&S Crafted Products
2 Black Rings
Rail #1
Rail #2
Rail #3
Rail #4
Rail #5

Advertisement

loading

Summary of Contents for A&S CRAFTED PRODUCTS BAND ROOM BRUS30

  • Page 1 BRUS30/BRUS18 BAND ROOM SOPRANO UKULELE RACK ASSEMBLY INSTRUCTIONS CONTENTS The Ukulele Rack ships in 2 cartons*: • One contains 2 sides • One contains 2 round stickers, 2 black rings, 12 wood rails, 2 handles, felt*, dowels & vinyl sleeves**, these instructions, and the following hardware: 4 Wheel Brackets...
  • Page 2 3. Begin fastening one of the rails to one of the sides. A. Holding the rail in position, remove one of the screws that you previously inserted. Note the hole on the back side of the rail (Figure 3A). Back Side of Rail B.

This manual is also suitable for:

Band room brus18