ADDA M680GMA Operation Manual

Robotic vacuum cleaner

Hide thumbs

Table Of Contents

Table of Contents

Quick Links

Download this manual

Robotic Vacuum Cleaner

Operation Manual

M680GMA

Table of Contents

Need help?

Do you have a question about the M680GMA and is the answer not in the manual?

Questions and answers

Summary of Contents for ADDA M680GMA

Page 1 Robotic Vacuum Cleaner Operation Manual M680GMA...
Page 2: Table Of Contents
FCC Caution * Battery and Recharging Instructions WARNING ------------------------------------------------------------------------ 9 SPECIAL FEATURES -------------------------------------------------------- 10 MAJOR COMPONENTS AND ATTACHMENTS ------------------------ M680GMA OVERVIEW ----------------------------------------------------- 11 INSTALLATION GUIDE ------------------------------------------------------ 12 * Installing and Removing Side Brush * Battery Installation and Removal * Recharging Battery...
Page 3: Safety Instructions
3. Before starting M680GMA, be sure to install M680GMA dust bin filter properly in case of any damage of M680GMA. 4. Do not operate M680GMA on wet floor or in moisture conditions, e.g. bathroom. Water and moisture could damage the circuit board in M680GMA.
Page 4: Safety Instructions
Please call your local dealer for service information. 12. Turn off the power and remove the battery from M680GMA if the unit will not in use for a long period of time. 13. This appliance can be used by children aged from...
Page 5 SAFETY INSTRUCTIONS 14. WARNING: the plug must be removed from the socket-outlet before cleaning or maintaining the appliance. 15. Automatic battery-operated cleaners shall also be provided with cautionary instructions for room preparation and constant care. 16. Make sure that the appliance can be worked freely in the room (shall not be blocked or overturned etc…) and make sure that there is nothing that the appliance can overturn and create a hazard (clear...
Page 6: Fcc Caution
SAFETY INSTRUCTIONS FCC Caution: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Page 7 SAFETY INSTRUCTIONS RF warning for Mobile device: This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.
Page 8: Battery And Recharging Instructions
6. Use only the battery supplied with your M680GMA. 7. Charging adaptor is for indoors only. 8. The appliance is only to be used with the power supply unit provided with the appliance.
Page 9 SAFETY INSTRUCTIONS 11. If M680GMA requires cleaning, unplug the adaptor, switch off the unit and take out the battery. 12. The battery must be removed from the appliance before it is scrapped. 13. The appliance must be disconnected from the supply mains when removing the battery.
Page 10: Warning
WARNING Following objects are strictly banned, otherwise the vacuum cleaner will be damaged or fire calamity will be caused, which bring such accidents as human body injuries: - Don’t pick up large or sharp broken such as glasses. - Don’t pick up harming or erodent liquids (solvent, corrosive, detergent…).
Page 11: Special Features
Working Patterns: "Z" Type Along the wall With Gyro and main wheel encoder sensors, M680GMA could build the simple map so It could clean your rooms and back to the dock station successfully when its power is low. With Mobile APP, the real-time mapping could be shown on the APP. Also, the remote control could be made from APP too.
Page 12: M680Gma Overview
M680GMA OVERVIEW IR Receiver (for Docking Station) Control Panel and LED Display Bumper Power Switch D.C. jack Contact Plates for Automatic Charging Side Brush Front Small Wheel Anti-Cliff Sensor Intake Valve Side Brush Left and Right Wheels Wheel Cover Heat Vent...
Page 13: Installation Guide
INSTALLATION GUIDE Installing and Removing Side Brush: To install: Push the brush directly onto the holder.(Fig. 1) To remove: Hold two opposite sides of the brush as shown in Fig. 2, and evenly pull upward to remove the brush. PULL UP! Side brush PRESS holder...
Page 14: Battery Installation And Removal
INSTALLATION GUIDE Battery Installation and Removal: 1. Turn off the power switch before installing the battery. 2. The details on how to remove the battery: To open the battery cover first by pressing the two points “A” (marked in the below diagram) and slide the battery cover in the direction of arrow “B”...
Page 15: Recharging Battery
4. To make sure the battery always at full charged status, the unit will be charged 15 min every hour after full. 5. When the M680GMA is in the "Battery Low" situation, “ ” (Power) will stay in the RED.
Page 16: Proof Test
INSTALLATION GUIDE Proof Test: Please try to test the installation of docking station, if the vacuum cannot go back to the docking station and charge successfully, then please replace the docking station to the proper height. Test by the unit, turn on the power switch of the unit, Use ( ) on APP or press robotic control panel icon to control the robot go back to the docking...
Page 17: Preparation Of Room Containment
INSTALLATION GUIDE Preparation of Room Containment: 1. Turn the power switch off. 2. Press two points mark A and slide the cover in the direction of arrow B as shown in the diagram below. 3. Insert four size AA batteries and match "+"and "-"...
Page 18: General Operation
. Intake Valve is stuck with dirt. Ž .Wipe out the inner and outside of Intake Valve area. Room containment of M680GMA may contain the cleaning area by putting it in a proper place. For example: To contain the Robot Cleaner cleaning area A (shaded area) and not crossing to area B by putting the Room containment in the position as shown in Fig.
Page 19: Control Panel
GENERAL OPERATION Control Panel: Docking LED Indicator Double 8 LED Display Wifi Connection Status ICON Clean Pattern ICON Dust Bin Full or Nozzle Block Power Button LED Indicator Docking Button Small Area Clean Button (Wifi pairing Button)
Page 20: Download App And Scheduling Setting
GENERAL OPERATION Download APP and scheduling setting : How to Download APP: 1. To download " SmartCleanerQ " APP from Playstore or APP store. 2. Scan the QR code and download APP. Android Scheduling setting from APP: ※The vacuum cleaner can function normally no matter Wi-Fi is connected or not.
Page 21: Basic Operation
GENERAL OPERATION Basic Operation: →Manual work ※When LED Indicator lights on. → Check: Œ . Dust bin is full. . Intake Valve is stuck with dirt. Ž . Wipe out the inner and outside of Intake Valve area. 1. Turn ON the power switch, wait for power LED light on(green).
Page 22 The unit will detect the The bumper stuck. error and fix automatically . The unit lifted up from the floor. Put M680GMA back on the floor. Remove the cleaner from dark floor The unit stuck on the cliff or stair. surface.
Page 23: Cleaning And Maintenance
CLEANING AND MAINTENANCE Maintenance Method: The operation and maintenance of the M680GMA is very simple. After each use, clean any dirt left behind on the dust bin and filter. It is not necessary to clean the intake after every use.
Page 24 CLEANING AND MAINTENANCE 3. Open the upper cover of the dust bin. Side buckle 4. Lift up and take out the filter. 5. Throw away the dust and dirt from the dust bin.