Advertisement
INDEX
1. General information
2. Applicable standards, field of application, cautions and warnings
3. Marking
4. Operating principle
5. Mask components
6. Donning and tightness test
7. Maintenance, cleaning and disinfection
7.1. Inspections and periodic maintenance
7.2. Cleaning
7.3. Disinfection
8. Tightness test
8.1. Performance tester
8.2. Testing
8.3. Leak tightness of mask and exhalation valve
9. Storage
10. Specific maintenance instructions and replacement of spare parts
10.1 Replacement of an exhalation valve
10.2 Replacement of inhalation valve
10.3. Replacement of inner mask
11.
Explosion of the mask's components.
1
Advertisement
Table of Contents
Summary of Contents for MILLA EURMASK PANAREA
- Page 1 INDEX 1. General information 2. Applicable standards, field of application, cautions and warnings 3. Marking 4. Operating principle 5. Mask components 6. Donning and tightness test 7. Maintenance, cleaning and disinfection 7.1. Inspections and periodic maintenance 7.2. Cleaning 7.3. Disinfection 8.
-
Page 2: General Information
MILLA. S.r.l. Technical alterations of this equipment are not allowed. MILLA S.r.l has carefully worded and edited this instruction manual. However, in no event shall MILLA, srl be liable for any damage caused by misunderstanding of the text, misprints or incompleteness. -
Page 3: Specific Conditions Of Use
- mechanical stress; - explosions in the atmosphere; - airborne toxic substances or polluted atmosphere. MILLA technical services are at your disposal for any assistance, explanation, advice or information you might need. 3. MARKING PANAREA mask is CE marked according to the European Community Directive 89/686 since the tested samples meet the requirements of EN 136:98 standard. -
Page 4: Operating Principles
MARKING ON PANAREA PANAREA EN 136:98 CL2 : EN standard and mask class Manufacturer, Year of manufacture, CE marking EURMASK = Manufacturer's identification (LOGO) = Year of manufacture (1998), two digits CE0426 = CE marking 0426 = Identification number of the notified body carrying out production control 7000 = reference number... -
Page 5: Maintenance, Cleaning And Disinfection
DONNING AND THIGHTNESS TEST Use the adjustable buckles to loosen the harness, Loosen the two straps of the neck harness, Place the mask in front of the face holding it by the back of the neck har- ness, place the chin in the special groove on the mask and put the har- ness over the head.) Pull the straps back in the sequence "neck", "temple"... - Page 6 The numbers indicated in the table have the following meaning: 1. Sample testing can be carried out only if the device is still in its original hermetic packing. 2. Spare parts: After the replacement of spare parts, which could modify the leak tightness, a total check of the mask is needed.
- Page 7 The performance tester can be supplied by MILLA S.r.l. TESTING Put the rubber balloon between the face blank and the harness and inflate it in order that the face piece seal of the mask is properly adjusted on the surface of the balloon.
- Page 8 Make sure that all the component parts are correctly assembled. groove is not dirty or damaged and clean it, if necessary. Insert the new spare parts, connecting them carefully to the inner half mask. Reassemble the clamping rings and tighten them strongly by using the special tool in order to ensure an appropriate tightening.
- Page 9 CAP FOR EXHALATION AND INNER MASK VALVE EQ2024 EQ2020 INHALATION VALVE ASSEMBLY HOUSING BUCKLES, PINS AND ROTARY EQ2016 INNER MASK EQ2019 FASTNERS FOR HARNESS MADE BY MILLA c/da Saverino s.n.c. 94017 Regalbuto (EN) Italy Tel. 093571144 fax 093577055 mail info@millasrl.it...
Need help?
Do you have a question about the EURMASK PANAREA and is the answer not in the manual?
Questions and answers