JHCOOL JH168 Owner's Manual

Hide thumbs

Table Of Contents

Table of Contents

Quick Links

Table of Contents

Need help?

Do you have a question about the JH168 and is the answer not in the manual?

Questions and answers

Summary of Contents for JHCOOL JH168

Page 2: Table Of Contents
Models: JH168 Read all instructions carefully before setting up and operating this unit. This manual is designed to provide you with important information needed to setup, operate, maintain, and troubleshoot your cooler. Due to continuous research and development the specifications herein are subject to change without notice.
Page 3 GUIDE FOR ADD WATER AND DRAIN ................7 CIRCUIT DRAWINGS ......................7 INSPECTION AND DEBUGGING BEFORE RUNNING ..........7 GUIDE FOR OPERATION ....................8 CLEAN AND MAINTAINING ..................10 TROUBLE SHOOTING ....................11 TECHNICAL PARAMETERS ..................12 Page | 3...
Page 4: Foreword
FOREWORD Thank you for your trust and support for choosing our Evaporative Air Cooler! Please read this manual carefully before using it. The Evaporative Air Cooler comes with the Most Advanced evaporative cooling technology and the Modern management. It will make your life easier and more comfortable.
Page 5: Inspection And Preparation Before Assembling
should not less than 85% of airflow when mechanical exhausting.) Mechanical can be combined with the natural exhaust. 3. Debugging the cooler when the first running. Ensure that the operating current at the rated current range. 4. Keep away any source of fire when assembling or operating the cooler. 5.
Page 6: Guide For Installation And Uninstall Of Truckles And Horse
4. A globe-valve is needed near the intake hose, and an extra hose connector is needed for cleaning. 5. Over-current and leakage protection switch should be added on the feed circuit, to protect the cooler, the wire net, and the safety of people. GUIDE FOR INSTALLATION AND UNINSTALL OF TRUCKLES AND HORSE 1.
Page 7: Guide For Add Water And Drain
GUIDE FOR ADD WATER AND DRAIN Add water: 1. pull out the affusion hole, as pic 5; 2. add water from this hole, as pic 6. Drain: Open the valve cover wither shins, also close it clockwise after drain, as pic 7. CIRCUIT DRAWINGS INSPECTION AND DEBUGGING BEFORE RUNNING 1.
Page 8: Guide For Operation
3. Check the water supply to be sure there is no leakage. 4. Debug the water level in the water tank. 5. Check if the power supply connection is correct. 6. Check if the assembling and connection of the power control are correct. 7.
Page 9 COOL: Switch to cool mode. Reserved. SWING: Start or stop swing. TIMER: Start timing function. Reserved. Operating introduction Please ensure the power lines are connected correctly before using! 1) ON/OFF Press this button under the state of stand-by, then it will start running. The mode and the airflow will be the same as the last state when you power off it.
Page 10: Clean And Maintaining
by the hour. It will start the air cooler automatically in the stand-by state and stop it automatically when it is running during the time is arrived. “H x” (“x” means the time you set) will be showed on the temperature indicator during the time is setting, and the temperature will be showed again on it after the timer takes effective.
Page 11: Trouble Shooting
TROUBLE SHOOTING NO. Problem Reason Solution Power off or incorrect power Replace it connection Air cooler does Controller breakdown Replace it not work Fuse burnt Replace it Electrical mainboard is broken Replace it The pump is broken Replace it No water or not enough water Add it No cooling The cool key on the controller is...
Page 12: Technical Parameters
TECHNICAL PARAMETERS 8000 Axial MAX Airflow(m3/h) Fan Type Pressure(Pa) Speed 0.38 Power(kW) Noise(dBA) ≤62 Voltage 220-240 Outlet 625×640 / 50 Dimension(mm) /Frequency(V/Hz) (685+30)×640×100 Pads Rated Currency (A) (685+30)×200×50 Dimension(mm) Overall 800×480×1380 Net Weight(kg) Dimension(mm) Operating Weight(kg) Water Store(L) Page | 12...