Table of Contents
Advertisement
Quick Links
Manual for low radiation wireless access points
with JRS eco-wifi 01A and JRS eco-wifi 03 firmware
Introduction
Less radiation, same performance. Share the Internet throughout your home or office while
minimizing your exposure to electromagnetic radiation, with the low EMF wifi firmware
from JRS.
Did you know that normal Wi-Fi
10 times per second and 24 hours per day, even when they are not used? The solution is a low
radiation wifi router. These routers come with the unique JRS eco-wifi firmware installed: an
operating system that reduces electromagnetic radiation by 90% in stand-by. This reduces
exposure to electromagnetic radiation from the router by a factor of 10, measurably.
•
Reduce wifi radiation by 90% in standby:
pulse frequency reduced to only once per second.
Connection throughput and network stability remain the same.
•
Options for completely (100%) turning off wifi radiation:
•
Scheduled wifi switch-off (for example during night time)
•
Manual on-/off-switch for wifi transmitter.
•
Fine adjustment of range with 1 milliwatt step size:
achieve up to 95% reduction in transmit power.
All functions of your existing ADSL, cable or glass fibre modem, like for example internet
telephony, can still be used. You connect the wifi router to your modem using a standard
network cable. Next, the wifi function of your existing modem needs to be switched off in its
configuration page, to minimize unneccesary wifi radiation, because this function is taken
over by the eco-wifi router. You may contact you provider's customer service for assistance.
The exposure to EM radiation from the laptop or other wirelessly connected equipment
remains unchanged. You may be able to reduce the transmit power of your computer's wifi
adapter with the Windows
free and minimizes health risk.
Gravin Juliana van Stolberglaan 31 (A3850)
2263AB Leidschendam
The Netherlands
+31 85 25 00 235
www. jrs electrohealt h.com
info@ jrs electrohealt h.com
®
routers for wireless internet unnecessarily transmit a signal
®
Device Manager. A wired internet connection is radiation-
1
Copyright 2017 JRS Electro Health – V15
Advertisement
Table of Contents
Summary of Contents for JRS Eco-WiFi 01A
- Page 1 10 times per second and 24 hours per day, even when they are not used? The solution is a low radiation wifi router. These routers come with the unique JRS eco-wifi firmware installed: an operating system that reduces electromagnetic radiation by 90% in stand-by. This reduces exposure to electromagnetic radiation from the router by a factor of 10, measurably.
- Page 2 2. Mount the antennas on the eco-wifi. Connect the power adapter and plug the adapter in to a power outlet. Important! Switch off the built-in wifi of your Internet modem (if applicable). If you don't know how, ask the customer service of your provider for help. Copyright 2017 JRS Electro Health – V15...
- Page 3 2. Change the Transmit Power field. The lowest possible setting is 1mW. The actual measured transmission power at that setting (measured by JRS) is a factor of 10-20x below the default setting. The lower the setting, the lower your exposure to EMF.
- Page 4 4. Check whether the filesystems you will be using are checked (in most cases FAT). 5. Check whether Automount is checked. 6. Go to the submenu File Sharing. 7. Check Yes, no authentication. Copyright 2017 JRS Electro Health – V15...
- Page 5 The eco-wifi can also be configured as a switch instead of as a router. This can be necessary for example in order to be able to reach a a Network Attached Storage device from devices Copyright 2017 JRS Electro Health – V15...
- Page 6 3. Click on save (at the bottom of the page). 4. Note: from now on, the settings menu of the eco-wifi can be reached by typing in Internet Explorer the new IP number that you have chosen in step 2. Copyright 2017 JRS Electro Health – V15...
- Page 7 – Lower the 'beacon interval' to 800 in the menu Advanced –-> Wireless. For the eco-wifi-03: do this both for the 2.4GHz channel and the 5GHz channel (is shown twice). After changing the settings click on save at the bottom of the page. Copyright 2017 JRS Electro Health – V15...
- Page 8 (such as certain wireless video links). If the 5GHz network is not showing on your wireless device – In the menu Advanced –> Wireless, change the country setting for 5GHz to the correct value. Copyright 2017 JRS Electro Health – V15...
Need help?
Do you have a question about the Eco-WiFi 01A and is the answer not in the manual?
Questions and answers