EvenMidi H9 Manual

TRICK: If you are in SOLO Mode and entering in
Looper MODE, the «PSW» footswitch isn't active
for CC Midi message like in DUAL MODE. Press
«PSW» footswitch to switch to SOLO Mode to
control your Second Eventide H9 while your
Looper is Playing. Press again the «PSW» and
you're back to Looper :). De nitive exit by
Holding down «UP» footswitch.
6 - LIVE MODE
Live mode allows you to directly load 6 presets in
DUAL mode or 3 presets by Eventide® in SOLO
mode. To enter or exit Live Mode, enter in the Midi
settings (Press the footswitch "UP" for 5 seconds)
then press the footswich X1 for 2 seconds. The
green LED and the yellow LED will blink. The PSW
footswitch allows access to the 2nd bank in DUAL
mode or to switch to the other Eventide® in SOLO
mode. The 3 footswitches send Program Change:
PC0 PC1 PC2 (PC3 PC4 PC5 in DUAL mode if the
PSW footswitch is activated). By re-pressing on the
same footswitch the e ect is bypassed (PC125).
The LEDs have a special behavior: the 3 LEDs on the
right (red, blue and yellow) respectively correspond
to the activation of each preset. When the preset is
bypassed the LEDs are o .
All EvenMidi functions are retained in Live Mode
(access to Looper mode, access to midi settings
etc.). When you exit Looper mode, the Eventide is
bypassed (PC125).
You can access your wanted presets by setting
the Eventide®. Hold Down Hotknob + right
Footswitch: MIDI> RCV.MAP> [0 or 1 or 2 or 3 or 4
or 5] .PresetNumberWanted. Do not change
PC125, that's the Eventide® default bypass.
7 - RESETTING
Enter in MIDI Settings Mode (Hold «UP» 5 seconds)
and press the "PSW" footswitch for 5 seconds. The
red LED will blink. MIDI channels, calibration and
Modes will be reset by default.
8 - WARRANTY
One year warranty for a normal usage. Don't put it
on the water and do not apply an excessive voltage
(max 12V). If the warranty time is over we can x it
at your cost.
9 - MAINTENANCE
You normally don't have any maintenance. Clean
the controller with a damp cloth.
10 - CONCLUSION
Well it's time to play! Hope it will t perfectly on
your pedal board. Send us a cool picture with you
and the controller on your rig or tag us on
Facebook/Instagram/Twitter, we will appreciate ;).
Have fun and all the best!
EvenMidi team
Eventide® is a trademark by Eventide inc. EvenMidi
has no connection or a liation with Eventide® inc.
The TimeFactor PitchFactor ModFactor et Space
products are e ects created by Eventide®.
CAUTION TO REDUCE THE RISK OF FIRE OR ELECTRIC
SHOCK DO NOT EXPOSE THIS EQUIPMENT TO
RISK OF ELECTRIC SHOCK
RAIN OR MOISTURE
DO NOT OPEN
AVIS: RISQUE DE CHOC ELECTRIQUE-NE PAS
OUVRIR.
This equipment has been tested and found to comply with the limits for a Class B digital
device pursuant to Part 15 of FCC rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired
operation.
www.evenmidi.com
Notice - English
Thank you for purchasing our Midi controller. We work on it since the Eventide® H9 release : improving,
switching technology, create speci c demands... First it was a DIY project and now it's a professional tool.
Speci cations
MIDI OUT/THRU MIDI IN
to Eventide® H9 MIDI IN (routing THRU)
MIDI OUT MIDI IN
Mix Dly Mix Dly Time A
Mix Pitch Mix Pitch A
Intensity Type Depth
Mix Decay Size
Ch1/2
Looper
Xnob
Depth/Key
Depth Mod
Psw
Xnob
X1
WARNING
AVERTISSEMENTS
Use only with 9V DC 200mA 2,1mm negative center
power supply. Avoid spilling liquids onto/into the unit. Do
not expose to excessive heat or moisture. Do not open –
there are no user serviceable parts inside.
MADE IN FRANCE
TRS - Expression pedal Connect a power supply 9V DC
From 10k to 50k Ohms 2,1mm - negative center 200mA
EXP DC 9V 2,1mm
On
Dly Time B Fdbk A Fdbk B
Midi
Pitch B Delay A Delay B
Speed Shape Xnob
Delay Low High
Solo
Depth Speed Filter
Speed / Scale Xnob Ynob
Speed Mod Mod Rate Mod source
Ynob FxMix Contour