Advertisement
Quick Links
Advertisement
Summary of Contents for CERAMBOT Bio
- Page 1 CERAMBOT Bio Instruction Manual Version Date Check 1.0.2 20190910 Jony...
- Page 2 1. CERAMBOT Bio default power supply is 50/60Hz-220V input, other input voltages need transformer conversion, equipped with transformer. 2. CERAMBOT Bio needs to be equipped with a stable gas source, with a volume of at least 8L and a pressure of at least 0.6MPa.
- Page 3 Print parameters: Equipment 600*450*600mm space Molding space 140*100*80mm Input voltage 50/60 Hz 220v Print material HA, BCP,TCP...
- Page 4 It includes one machine, one power cord, one data cable, one U disk (the format needs to be FAT32 format), one set of tools, one 6*4mm air pipe, several PVC gaskets, matching syringes, pistons and needles. (Some equipment supporting 110v to 220v transformer) The whole machine is as follows: CERAMBOT Bio printer...
- Page 5 CERAMBOT Bio supports U disk offline printing and also supports online printing. The CERAMBOT Bio is inserted behind the U disk, which can be printed offline directly from the USB flash drive. It can also be printed by computer control using Mini USB and controlled by repetier-...
- Page 6 A. CERAMBOT Bio use steps 1) After importing the gcode print file generated after CURA is sliced into the USB flash drive, insert it into the USB flash drive slot on the back of the printer to print from the front control panel.
- Page 7 3) Before printing, select change filements in the control panel, click to extrude the material under orange or green, and adjust the pressure value of the corresponding gas path, and observe that the material is just extruded. (The pressure regulator should be pulled up before use to adjust the air pressure value.
- Page 8 4) Start printing. After ensuring that the platform has been leveled, the needle is just in contact with the printing platform and the material can be sent out smoothly from the needle. You can print by selecting print from the control panel and then selecting the generated slice file CERAMBOT Bio.gcode.
- Page 9 B. Slice software settings CERAMBOT Bio supports a variety of slicing software, CURA, slic3r and simplify3d. Different software has different advantages and disadvantages. Here are the tutorials for using CURA and simplify3d. This version is cura 3.6.0 version Set as shown below: 1.
- Page 10 ○ 4 The installation process will pop up the window where the arduino driver is installed. Please keep the default installation. Follow the prompts and the installation is complete. 2. Initial use configuration Steps：...
- Page 11 ○ Run Cura, click on Settings > Printers > Add Printer > Custom, type "CERAMBOT Pro & Air" in the printer name, then click "Add Printer", the printer settings interface will pop up ; ○ 2 Set the printer parameters as shown below.
- Page 12 G28 ;Home G1 Z15.0 F1800 ;Move the platform down 15mm ;Prime the extruder G92 E0 M104 S0 M140 S0 ;Retract the filament G92 E1 G28 X0 Y0...
- Page 14 Click Finish。 3. Click on the manage material to set up the material as shown below. Click import, import the file: Bio-0.1-material.xml.fdm_material, and then select material parameter Bio-s shown:...
- Page 15 1) Layer height: the height of each layer printed, the smaller the print surface is finer, but the slower it is, the parameter range is 0.5-3, CERAMBOT Pro & Air uses 1.5 nozzles by default. 2) Wall thickness: the thickness printed on the outer surface of the model.
- Page 16 Configure Cura's parameter slice print settings as shown below, or import the configuration file directly. 1) Import the configuration file directly: Select the profile's manage profiles as shown below and import the configuration file: cerambot.curaprofile...
- Page 17 Select profile: CERAMBOT Bio...
- Page 18 2) Or manually configure the file, set as shown below.
- Page 25 Simplify3D tutorial Simplify3D software is paid software and is available for purchase. Here is a brief description of the software configuration tutorial for simplify3d 1. Configure machine parameters 1. Resize the model...
- Page 26 1. Print parameter settings: Layer thickness setting: Outer ring setting...
- Page 27 Fill settings...
- Page 28 Temperature setting, set to 0...
- Page 31 Speed setting...
- Page 33 You can also use the repeater to print online. After installing the repeater, set the following: https://www.repetier.com/download-now/...