Advertisement
Quick Links
Advertisement
Summary of Contents for Printspace 3D Altair
- Page 1 Quick Start Guide PrintSpace 3D • Altair 3D Printer | www.printspace3d.com | 1...
- Page 2 Altair transforms ideas into physical products and is used to prototype and create three dimensional models and end-use products. What will you create? 2 | PrintSpace 3D • Altair 3D Printer | www.printspace3d.com...
-
Page 3: Printing Process
.stl file. extruder will load the your print. on the front navigation filament. panel of the printer. PrintSpace 3D • Altair 3D Printer | www.printspace3d.com | 3... - Page 4 CarbonGlide Rods Filament Guide Tube Ball Joints NOVA Hot End Power Connector & Power Switch (Back of Printer) Print Bed Sensors Micro SD Card Slot Navigation Dial Emergency Stop Display/Control 4 | PrintSpace 3D • Altair 3D Printer | www.printspace3d.com...
- Page 5 In the Box Power Cable Part Removal Tool Micro SD & Adapter Tweezers Business Card Filament Spool Holder Quickstart Guide Printer Note: You will need a surge protector. PrintSpace 3D • Altair 3D Printer | www.printspace3d.com | 5...
- Page 6 Unpacking 1. Set the box on its side with the PrintSpace 3D ™ 1 & 2. 3 - 5. sticker pointing up, then open the box 2. Grab the carbon fiber rods and slide Altair out with the foam still around it.
- Page 7 Power Connector on air conditioner vent the back of Altair. or leaving Altair in extreme temperature 4. Insert the included micro SD card into the environments. SD slot on the Display Panel. PrintSpace 3D • Altair 3D Printer | www.printspace3d.com | 7...
-
Page 8: Calibrating The Printer
Important: Don’t touch the bed during the calibration routine – it will trigger the sensors and disturb the calibration. Make sure Altair is not connected to your computer through the USB port during the Auto-Calibration routine. If the computer tries to access the printer (which it often does automatically) it can disturb calibration. - Page 9 HOT. Do not touch the NOVA Hot End or Print Bed speed/quality of print is reached until they are completely cooled or this may result (typically a lower speed will increase in injury. resolution). PrintSpace 3D • Altair 3D Printer | www.printspace3d.com | 9...
- Page 10 Wiping down the BuildTak with an alcohol pad between prints will help prints stick better to the bed while increasing the life of the BuildTak. Replacement BuildTak can be ordered at www.printspace3d.com/store. 10 | PrintSpace 3D • Altair 3D Printer | www.printspace3d.com...
- Page 11 Software You will need a model in a .stl file format in order to print on Altair. Most CAD and 3D modeling software supports exporting to this format. After you have created or downloaded a .stl file, the file will need to be converted to .gcode so Altair can read it.
- Page 12 Biodegradable, get the strength printing pliable, strong, food contact is stiff and various colors. odor free. of ABS. Minimal material. high thermal or industrial lightweight. degradation and durability. applications. warping. 12 | PrintSpace 3D • Altair 3D Printer | www.printspace3d.com...
-
Page 13: Accessories And Consumables
If you would like extra accessories or replacement consumables, shop our store at www.printspace3d.com/store Various Nozzles Buildtak NOVA Hot End Spool Holder and Sizes • Low Profile • Standard • Wear-Resistant • High Lubricity • Fine Detail • Faster Printing PrintSpace 3D • Altair 3D Printer | www.printspace3d.com | 13... -
Page 14: Support And Warranty
Note: This warranty shall be considered null and void in the event that the Altair printer housing is opened. The warranty does not cover issues that may arise from leaving a printer in extreme temperature environments. Hacking or otherwise changing the safe operating limits of the printer will void the warranty. - Page 15 www.printspace3d.com...
Need help?
Do you have a question about the Altair and is the answer not in the manual?
Questions and answers