PacketLight Networks PL-1000RO 3.3 Installation And Configuration Manual
  1. Manuals
  2. Brands
  3. PacketLight Networks Manuals
  4. Multiplexer
  5. PL-1000RO 3.3
  6. Installation and configuration manual

PacketLight Networks PL-1000RO 3.3 Installation And Configuration Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
PL-1000RO 3.3 I
NSTALLATION AND
C
M
ONFIGURATION
ANUAL

Advertisement

Table of Contents
loading

Summary of Contents for PacketLight Networks PL-1000RO 3.3

  • Page 1 PL-1000RO 3.3 I NSTALLATION AND ONFIGURATION ANUAL...
  • Page 2 PacketLight Networks, Ltd. All Rights Reserved. The information shall not be used, copied, reproduced, or disclosed in whole or in part without the written consent of PacketLight Networks, Ltd. PacketLight Networks, Ltd. reserves the right, without prior notice or liability, to make changes in equipment design or specifications.

  • Page 3: Table Of Contents

    NSTALLING THE 2.3.1 P ................22 ACKAGE ONTENTS 2.3.2 R ................23 EQUIRED QUIPMENT 2.3.3 C .................23 ABLE ONNECTIONS 2.3.4 C ................26 ABLING XAMPLES PL-1000RO 3.3 I ACKET IGHT ETWORKS NSTALLATION AND ONFIGURATION ANUAL ONFIDENTIAL AND ROPRIETARY NFORMATION LL RIGHTS RESERVED AGE I...
  • Page 4 ..................50 LARMS 5.3.2 E ..................52 VENTS 5.3.3 C .............54 ONFIGURATION HANGES ....................55 AULTS 5.4.1 A ..................56 LARMS 5.4.2 E ..................58 VENTS PL-1000RO 3.3 I ACKET IGHT ETWORKS NSTALLATION AND ONFIGURATION ANUAL ONFIDENTIAL AND ROPRIETARY NFORMATION LL RIGHTS RESERVED AGE II...
  • Page 5 ................106 ENERAL 6.4.2 P ................107 ROVISIONING ............... 109 ANAGEMENT ONFIGURATION 6.5.1 MNG T ..................110 6.5.2 SFP T ..................112 PL-1000RO 3.3 I ACKET IGHT ETWORKS NSTALLATION AND ONFIGURATION ANUAL ONFIDENTIAL AND ROPRIETARY NFORMATION LL RIGHTS RESERVED AGE III...
  • Page 6 ........153 EFINING ULTIPLE ODES AS ULTI HASSIS 10 REMOTE MANAGEMENT CONFIGURATION ..........157 10.1 R ..........157 EMOTE ANAGEMENT ONFIGURATION XAMPLE PL-1000RO 3.3 I ACKET IGHT ETWORKS NSTALLATION AND ONFIGURATION ANUAL ONFIDENTIAL AND ROPRIETARY NFORMATION LL RIGHTS RESERVED AGE IV...
  • Page 7 APPENDIX B: ALARM AND EVENT MESSAGES ..........187 ..................187 LARM ESSAGES ..............189 ONFIGURATION VENT ESSAGES ................189 THER VENT ESSAGES PL-1000RO 3.3 I ACKET IGHT ETWORKS NSTALLATION AND ONFIGURATION ANUAL ONFIDENTIAL AND ROPRIETARY NFORMATION LL RIGHTS RESERVED AGE V...
  • Page 8 CONTENTS APPENDIX C: TROUBLESHOOTING CHART ............ 191 ................191 ROUBLESHOOTING HART INDEX ......................193 PL-1000RO 3.3 I ACKET IGHT ETWORKS NSTALLATION AND ONFIGURATION ANUAL ONFIDENTIAL AND ROPRIETARY NFORMATION LL RIGHTS RESERVED AGE VI...
  • Page 9 Figure 36: Configuration Changes Tab ..............60 Figure 37: WSS Fault Window ................61 Figure 38: Alarms Tab ...................62 Figure 39: Events Tab ...................64 Figure 40: Configuration Changes Tab ..............66 Figure 41: Management Port Fault Window ..............67 PL-1000RO 3.3 I ACKET IGHT ETWORKS NSTALLATION AND ONFIGURATION...
  • Page 10 Figure 81: MUX/DEMUX Tab ................. 117 Figure 82: EDFA Configuration Window ..............118 Figure 83: EDFA Tab ................... 119 Figure 84: Confirm Changes ................119 Figure 85: Confirm Changes ................120 PL-1000RO 3.3 I ACKET IGHT ETWORKS NSTALLATION AND ONFIGURATION...
  • Page 11 Figure 126: IP Addresses: PL-1000RO B (Example) ..........160 Figure 127: Static Routing Table (Example) ............160 Figure 128: SNMP Traps Table (Example) .............. 161 Figure 129: CLI Command Tree ................169 Figure 130: External ALARM Diagram ..............180 PL-1000RO 3.3 I ACKET IGHT ETWORKS NSTALLATION AND...
  • Page 12 CONTENTS Figure 131: DC Connector Wiring Diagram ............. 184 Figure 132: Protective Ground Terminal Wiring Diagram .......... 185 Figure 133: Fiber Shelf Diagram ................186 PL-1000RO 3.3 I ACKET IGHT ETWORKS NSTALLATION AND ONFIGURATION ANUAL ONFIDENTIAL AND ROPRIETARY NFORMATION LL RIGHTS RESERVED...
  • Page 13 Table 38: MNG Tab Parameters ................111 Table 39: SFP Tab Parameters ................112 Table 40: ALS Tab Parameters ................114 Table 41: Ethernet Tab Parameters ............... 116 Table 42: MUX/DEMUX Tab Parameters ..............118 PL-1000RO 3.3 I ACKET IGHT ETWORKS NSTALLATION AND...
  • Page 14 Table 56: MUX/DEMUX Port Specifications ............. 183 Table 57: Alarm Messages ................... 187 Table 58: Configuration Event Messages ..............189 Table 59: Other Event Messages ................189 Table 60: Troubleshooting Chart ................191 PL-1000RO 3.3 I ACKET IGHT ETWORKS NSTALLATION AND...

  • Page 15: Introduction

    Supports linear add/drop and ring topologies Two 100M management ports based on SFP optics for local or remote • management using an Optical Supervisory Channel (OSC) Automatic Laser Shutdown (ALS) on management ports • PL-1000RO 3.3 I ACKET IGHT ETWORKS NSTALLATION AND ONFIGURATION...

  • Page 16: Typical Application

    • Converge existing networks and new services over existing infrastructure Provide a fully optical layer solution, transparent to service rate and type • • Build cost-effective add and drop networks PL-1000RO 3.3 I ACKET IGHT ETWORKS NSTALLATION AND ONFIGURATION ANUAL...

  • Page 17: Figure 1: Typical Application For Pl-1000Ro Devices

    Typically the PL-1000RO may be used in a ring or linear add/drop topology. The following figure illustrates a ring with four sites connected with PL-1000RO devices. Figure 1: Typical Application for PL-1000RO Devices PL-1000RO 3.3 I ACKET IGHT ETWORKS NSTALLATION AND...

  • Page 18: Physical Description

    The PL-1000RO unit is a 19-inch/1U ETSI compliant unit with single or dual field-replaceable AC and/or DC power supplies and a pluggable FAN unit. Figure 3: PL-1000RO Unit without MUX/DEMUX PL-1000RO 3.3 I ACKET IGHT ETWORKS...

  • Page 19: 1000Ro Configurations

    This section describes some of the available configurations of the PL-1000RO. 1.2.1 MUX/DEMUX Module Configurations The PL-1000RO has two basic configurations: Without a MUX/DEMUX module • With a MUX/DEMUX module • PL-1000RO 3.3 I ACKET IGHT ETWORKS NSTALLATION AND ONFIGURATION ANUAL ONFIDENTIAL AND...

  • Page 20: Figure 5: Pl-1000Ro Data Ports Without Mux/Demux

    The following are the data ports of a PL-1000RO without a MUX/DEMUX module: COM: The common network port connected to the line. • • EXP: The express channels. A/D: The add/drop channels. • • OSC: The optical supervisory channel. PL-1000RO 3.3 I ACKET IGHT ETWORKS NSTALLATION AND ONFIGURATION ANUAL ONFIDENTIAL AND ROPRIETARY...

  • Page 21: Figure 6: Pl-1000Ro Without Mux/Demux Inside A Ring (Example)

    COM: The common network port connected to the line. • • EXP: The express channels. MUX: The input to the MUX/DEMUX module. • DEMUX: The output of the MUX/DEMUX module. • PL-1000RO 3.3 I ACKET IGHT ETWORKS NSTALLATION AND ONFIGURATION ANUAL ONFIDENTIAL AND...

  • Page 22: Wss Module Configurations

    WSS Module Configurations The WSS can be ordered with 100 GHz or with 50 GHz spacing. When ordered with 100 GHz, there are 44 available channels. When ordered with 50 GHz, there are 88 available channels. PL-1000RO 3.3 I ACKET IGHT ETWORKS...

  • Page 23: Edfa Module Configurations

    The PL-1000RO can be ordered with one or two optional EDFA modules that are used to amplify the optical power of the DWDM signal. The EDFA modules can be used as a Booster and/or Pre-Amp. PL-1000RO 3.3 I ACKET IGHT...

  • Page 24: Power Supply Unit Configurations

    The FAN unit has an automatic speed control mechanism that supports lower noise, improved MTBF and power saving. Air intake vents should be clear of obstruction. PL-1000RO Management This section describes the PL-1000RO management. PL-1000RO 3.3 I ACKET IGHT ETWORKS NSTALLATION AND...

  • Page 25: Management Ports

    This management channel may be multiplexed as an extra OSC wavelength by the optical add/drop multiplexer. The PL-1000RO supports two OSCs for multi-chassis application and for remote management with facility protection. PL-1000RO 3.3 I ACKET IGHT ETWORKS...

  • Page 26: Management Functionality

    For initial IP configuration and several other management tasks, the PL-1000RO supports CLI ASCII management. CLI management is accessible via the CONTROL serial port or Telnet/SSH connection. For more information, see (p. 165). PL-1000RO 3.3 I ACKET IGHT ETWORKS NSTALLATION AND...

  • Page 27: Technical Specifications

    Pre-Amp: +18 db • Input Power Booster: -24 to +16 dBm • Pre-Amp: -36 to -15 dBm Keeps the amplifier gain fixed without dependency when adding or removing services. PL-1000RO 3.3 I ACKET IGHT ETWORKS NSTALLATION AND ONFIGURATION ANUAL ONFIDENTIAL AND...
  • Page 28 • Green: Normal operation • OFF: No Critical alarm detected • Red: Critical alarm detected • OFF: No Major alarm detected • Red: Major alarm detected PL-1000RO 3.3 I ACKET IGHT ETWORKS NSTALLATION AND ONFIGURATION ANUAL ONFIDENTIAL AND ROPRIETARY NFORMATION...
  • Page 29 Redundancy Single or dual feeding, pluggable AC Source 100 to 240 VAC, 50/60 Hz, 1.5A maximum DC Source –48 VDC 3A maximum Power 60W maximum Consumption PL-1000RO 3.3 I ACKET IGHT ETWORKS NSTALLATION AND ONFIGURATION ANUAL ONFIDENTIAL AND ROPRIETARY NFORMATION...
  • Page 30 • GR-1089-CORE, Issue 4 • Standards IEC/EN 60825-1 Safety • IEC/EN 60825-2 • IEC/EN/UL 60950-1 • Telcordia SR-332, Issue 2 • RoHS 5/6 PL-1000RO 3.3 I ACKET IGHT ETWORKS NSTALLATION AND ONFIGURATION ANUAL ONFIDENTIAL AND ROPRIETARY NFORMATION LL RIGHTS RESERVED...

  • Page 31: Wss Specifications

    VOA Error 0.5 dB to 1 dB Optical Power Limit 1 Channel 20 dB (maximum), In passband Optical Power Limit All Channels 27 dB Entire input spectrum PL-1000RO 3.3 I ACKET IGHT ETWORKS NSTALLATION AND ONFIGURATION ANUAL ONFIDENTIAL AND ROPRIETARY...

  • Page 33: Installation

    Intentional interruption is prohibited. Before connecting any cables, the protective ground terminal of the PL-1000RO must be connected to a protective ground (see Connection Data (p. 179)). PL-1000RO 3.3 I ACKET IGHT ETWORKS NSTALLATION AND ONFIGURATION...

  • Page 34: Figure 11: Class 3B Laser Warning

     Do not try to open the enclosure. There are no user serviceable components inside.  Do not operate controls, make adjustments, or perform procedures to the laser device other than those specified herein.  Allow only authorized service technicians to repair the unit. PL-1000RO 3.3 I ACKET IGHT ETWORKS NSTALLATION AND...

  • Page 35: Protection Against Electrostatic Discharge

    Power Connectors (p. 184)). 2.2.3 Ambient Requirements The recommended ambient operating temperature of the PL-1000RO is 0° to +45°C/+32° to +113°F, at a relative humidity of 5% to 85%, non-condensing. PL-1000RO 3.3 I ACKET IGHT ETWORKS NSTALLATION AND ONFIGURATION ANUAL...

  • Page 36: Electromagnetic Compatibility Considerations

    3m power cord equipped with the appropriate plug  power: DC power cord  • Fiber tray (if ordered) Kit for rack installation: 19", 23" (if ordered), or 600 mm ETSI (if ordered) • PL-1000RO 3.3 I ACKET IGHT ETWORKS NSTALLATION AND ONFIGURATION ANUAL ONFIDENTIAL AND...

  • Page 37: Required Equipment

     The power cord plug should only be inserted in an outlet provided with a protective ground (earth) contact. The protective action must not be negated by using an extension cord (power cable) without a protective conductor (grounding). PL-1000RO 3.3 I ACKET IGHT ETWORKS...
  • Page 38 Connect the 10/100 Base-T ETH port to the local LAN using a cable with an • RJ-45 connector. For specific information regarding pin allocations in the PL-1000RO connectors, see Connection Data (p. 179). PL-1000RO 3.3 I ACKET IGHT ETWORKS NSTALLATION AND ONFIGURATION ANUAL...
  • Page 39 The following is applicable only to a PL-1000RO without a MUX/DEMUX module. To cable the Add/Drop port: Connect the Add/Drop LC connector to the fiber that carries the add/drop • channels coming from the MUX/DEMUX connected to the local devices. PL-1000RO 3.3 I ACKET IGHT ETWORKS NSTALLATION AND...

  • Page 40: Cabling Examples

    4. Connect the MNG LC connector of the ribbon to one of the MNG ports of the PL-1000RO. 2.3.4 Cabling Examples This section provides cabling examples of a ring PL-1000RO with MUX/DEMUX and without MUX/DEMUX. PL-1000RO 3.3 I ACKET IGHT ETWORKS NSTALLATION AND ONFIGURATION...

  • Page 41: Figure 12: Cabling Of A Ring Pl-1000Ro Without Mux/Demux (Example)

    Cabling Example of a Ring PL-1000RO with MUX/DEMUX The following figure illustrates an example of cabling two PL-1000RO nodes (west and east) with MUX/DEMUX modules, with PL-1000 nodes, inside a ring. Figure 13: Cabling of a Ring PL-1000RO with MUX/DEMUX (Example) PL-1000RO 3.3 I ACKET IGHT ETWORKS...

  • Page 43: Operation And Preliminary Configuration

    8 data bits  No parity  1 stop bit  Full-duplex  Echo off  Disable any type of flow control  PL-1000RO 3.3 I ACKET IGHT ETWORKS NSTALLATION AND ONFIGURATION ANUAL ONFIDENTIAL AND ROPRIETARY NFORMATION LL RIGHTS RESERVED...

  • Page 44: Turning On The Pl-1000Ro

    2. Configure the Ethernet port IP address via the terminal in order to support the Web-based application. 1. Acquire the Ethernet IP address using CLI if needed (see Configure Interface Ethernet IP Command (p. 174)). 2. At the prompt, type the following CLI command: PL-1000RO 3.3 I ACKET IGHT ETWORKS NSTALLATION AND ONFIGURATION ANUAL...

  • Page 45: Accessing The Web Application

    The default address can be changed by the user. If a different IP address is desired, it is necessary to configure the Ethernet port interface IP address of the PL-1000RO before accessing the Web (see Performing Preliminary Configuration (p. 30)). PL-1000RO 3.3 I ACKET IGHT ETWORKS NSTALLATION AND...

  • Page 46: Prerequisites For Accessing The Web Application

    User Name The user name and password are case sensitive. 6. In the Password field, type the password. Only alphanumeric characters without spaces are allowed. PL-1000RO 3.3 I ACKET IGHT ETWORKS NSTALLATION AND ONFIGURATION ANUAL...

  • Page 47: Navigating The Web Application

    This section describes the PL-1000RO item buttons, sidebar buttons, and tabs. 3.4.1 Item Buttons The following figure shows an example of the buttons used for performing operations in the Web application. Figure 16: PL-1000RO Item Buttons (Example) PL-1000RO 3.3 I ACKET IGHT ETWORKS NSTALLATION AND ONFIGURATION...

  • Page 48: Sidebar Buttons

    Performance: View system optical information and port performance monitoring • Security: Manage users’ accounts Topology: View network topology • • Maintenance: Perform maintenance tasks for the PL-1000RO PL-1000RO 3.3 I ACKET IGHT ETWORKS NSTALLATION AND ONFIGURATION ANUAL ONFIDENTIAL AND ROPRIETARY...

  • Page 49: Tabs

    PERATION AND RELIMINARY ONFIGURATION 3.4.3 Tabs The following figure shows an example of the tabs used for performing system security operations. Figure 18: PL-1000RO Tabs (Example) PL-1000RO 3.3 I ACKET IGHT ETWORKS NSTALLATION AND ONFIGURATION ANUAL ONFIDENTIAL AND ROPRIETARY NFORMATION...

  • Page 50: Logging Out Of The Web Application

    Read Only User Figure 19: PL-1000RO Users Tab Logging Out of the Web Application To log out of the Web application: Click • Logout You are logged out. PL-1000RO 3.3 I ACKET IGHT ETWORKS NSTALLATION AND ONFIGURATION ANUAL ONFIDENTIAL AND...

  • Page 51: Security Management

    There are two methods for user authentication: Local authentication • • Remote authentication PL-1000RO 3.3 I ACKET IGHT ETWORKS NSTALLATION AND ONFIGURATION ANUAL ONFIDENTIAL AND...

  • Page 52: Local Authentication

    Radius Access-Accept. Format: String Allowed values: • 1: read-only access • 2: read-write access • 4: admin access PL-1000RO 3.3 I ACKET IGHT ETWORKS NSTALLATION AND ONFIGURATION ANUAL ONFIDENTIAL AND ROPRIETARY NFORMATION LL RIGHTS RESERVED...
  • Page 53 Secret. 3. For each user, configure the following attributes: User-Name  Only alphanumeric characters without spaces are allowed. User-Password  Only alphanumeric characters without spaces are allowed. PL-1000RO 3.3 I ACKET IGHT ETWORKS NSTALLATION AND ONFIGURATION ANUAL ONFIDENTIAL AND ROPRIETARY...

  • Page 54: Security Settings

    (Non-Administrator): Change your password • (Administrator): Configure the Radius client • Radius tab To open the Security Settings window: Click Security. • The Security Settings window opens. PL-1000RO 3.3 I ACKET IGHT ETWORKS NSTALLATION AND ONFIGURATION ANUAL ONFIDENTIAL AND ROPRIETARY...

  • Page 55: Users Tab (Administrator)

    The password is hidden for security reasons. Verify The password for the user again. Only alphanumeric characters without spaces Password are allowed. The password is hidden for security reasons. PL-1000RO 3.3 I ACKET IGHT ETWORKS NSTALLATION AND ONFIGURATION ANUAL ONFIDENTIAL AND...

  • Page 56: Figure 22: Confirm Changes

    Password Only alphanumeric characters without spaces are allowed. The password is hidden for security reasons. 4. In the field, type the new password again. Verify Password 5. Click Modify. PL-1000RO 3.3 I ACKET IGHT ETWORKS NSTALLATION AND ONFIGURATION ANUAL ONFIDENTIAL AND...

  • Page 57: Users Tab (Non-Administrator)

    Users Tab (Non-Administrator) Figure 25: Users Tab (Non-Administrator) Non-administrator users cannot manage other users; however, they can use the Users tab to change their own password if they are on the local user list. PL-1000RO 3.3 I ACKET IGHT ETWORKS...

  • Page 58: Figure 26: Confirm Changes

    The password is hidden for security reasons. Verify Password Your password again. Only alphanumeric characters without spaces are allowed. The password is hidden for security reasons. PL-1000RO 3.3 I ACKET IGHT ETWORKS NSTALLATION AND ONFIGURATION ANUAL ONFIDENTIAL AND ROPRIETARY...

  • Page 59: Radius Tab (Administrator)

    2. Fill in the fields as explained in the following table. 3. Click Apply. The following confirmation message appears. Figure 28: Confirm Configuration 4. Click OK. The Radius client is configured. PL-1000RO 3.3 I ACKET IGHT ETWORKS NSTALLATION AND ONFIGURATION...

  • Page 60: Table 8: Radius Tab Parameters (Administrator)

    Verify Secondary Server The shared secret for the secondary Free text Shared Secret server again. Secondary Server The administrative status of the Up, Down Admin Status secondary server. PL-1000RO 3.3 I ACKET IGHT ETWORKS NSTALLATION AND ONFIGURATION ANUAL ONFIDENTIAL AND ROPRIETARY NFORMATION...

  • Page 61: Fault Views

    Whenever such a condition occurs, the PL-1000RO generates a time stamped event message and sends it as an SNMP notification to the registered management systems. The PL-1000RO logs the history of the last 512 events in PL-1000RO 3.3 I ACKET IGHT...

  • Page 62: Configuration Changes

    General Fault Viewing Procedure The following is the general procedure for viewing the PL-1000RO faults. The specific procedures for each item are provided in the following sections. To view the PL-1000RO faults: 1. Click Fault. PL-1000RO 3.3 I ACKET IGHT ETWORKS NSTALLATION AND...

  • Page 63: System Faults

    Events  Configuration Changes  The appropriate tab opens. Note that some or all of the fields may be read only. System Faults Figure 29: System Fault Window PL-1000RO 3.3 I ACKET IGHT ETWORKS NSTALLATION AND ONFIGURATION ANUAL ONFIDENTIAL AND...

  • Page 64: Alarms Tab

    Use the Alarms tab to view the current alarms, turn off the external alarm, export the list of alarms to a file, set the refresh rate, and stop the automatic refresh of the Fault display. To view current alarms: 1. Click the Alarms tab. PL-1000RO 3.3 I ACKET IGHT ETWORKS NSTALLATION AND ONFIGURATION ANUAL...

  • Page 65: Table 9: Alarms Tab Parameters

    Day of the week, Month, Day, Year, detected. HH:MM:SS, AM/PM Source The entity that caused the alarm. Severity The severity of the alarm. Critical, Major, Minor Message The type of alarm. PL-1000RO 3.3 I ACKET IGHT ETWORKS NSTALLATION AND ONFIGURATION ANUAL ONFIDENTIAL AND ROPRIETARY NFORMATION...

  • Page 66: Events Tab

     Green: Indicates that the corresponding alarm is cleared  White: Indicates informational messages  2. To export the Event Log to a file: 1. Click Export File PL-1000RO 3.3 I ACKET IGHT ETWORKS NSTALLATION AND ONFIGURATION ANUAL ONFIDENTIAL AND...

  • Page 67: Table 10: Events Tab Parameters

    Note Information related to the event. S.A.: The event is service affecting. • Blank: The event is not service affecting. • Other: Information related to the event. PL-1000RO 3.3 I ACKET IGHT ETWORKS NSTALLATION AND ONFIGURATION ANUAL ONFIDENTIAL AND ROPRIETARY...

  • Page 68: Configuration Changes Tab

    2. Click Start Refresh. The information is automatically updated after the specified number of seconds. 4. To refresh the Fault display manually, click Refresh The information is updated immediately. PL-1000RO 3.3 I ACKET IGHT ETWORKS NSTALLATION AND ONFIGURATION ANUAL ONFIDENTIAL AND...

  • Page 69: All Faults

    Fault display tab: View the Event Log, export the log to a file, set the refresh rate, • Events and stop the automatic refresh of the Fault display PL-1000RO 3.3 I ACKET IGHT ETWORKS NSTALLATION AND ONFIGURATION...

  • Page 70: Alarms Tab

    The fields are read only and explained in the following table. The color of the alarm background indicates the severity of the alarm: Red: Critical or Major alarm  Yellow: Minor alarm  PL-1000RO 3.3 I ACKET IGHT ETWORKS NSTALLATION AND ONFIGURATION ANUAL...

  • Page 71: Table 12: Alarms Tab Parameters

    The type of alarm. • Note Whether or not the alarm is service S.A.: The alarm is service affecting. affecting. • Blank: The alarm is not service affecting. PL-1000RO 3.3 I ACKET IGHT ETWORKS NSTALLATION AND ONFIGURATION ANUAL ONFIDENTIAL AND ROPRIETARY...

  • Page 72: Events Tab

     2. To export the Event Log to a file: 1. Click Export File The Opening table.csv dialog box appears. 2. Click Save File. 3. Click OK. PL-1000RO 3.3 I ACKET IGHT ETWORKS NSTALLATION AND ONFIGURATION ANUAL ONFIDENTIAL AND ROPRIETARY...

  • Page 73: Table 13: Events Tab Parameters

    Note Information related to the event. S.A.: The event is service affecting. • Blank: The event is not service affecting. • Other: Information related to the event. PL-1000RO 3.3 I ACKET IGHT ETWORKS NSTALLATION AND ONFIGURATION ANUAL ONFIDENTIAL AND ROPRIETARY...

  • Page 74: Configuration Changes Tab

    1. In the field, type the number of seconds that the window Refresh every should refresh. The minimum refresh rate is 2 seconds. 2. Click Start Refresh. PL-1000RO 3.3 I ACKET IGHT ETWORKS NSTALLATION AND ONFIGURATION ANUAL ONFIDENTIAL AND ROPRIETARY...

  • Page 75: Wss Faults

    Critical, Major, Minor, Cleared, Event Message The type of change. Note Information related to the change. WSS Faults Figure 37: WSS Fault Window Use the WSS Fault window to do the following: PL-1000RO 3.3 I ACKET IGHT ETWORKS NSTALLATION AND ONFIGURATION ANUAL ONFIDENTIAL AND...

  • Page 76: Alarms Tab

    Use the Alarms tab to view the current alarms, turn off the external alarm, export the list of alarms to a file, set the refresh rate, and stop the automatic refresh of the Fault display. PL-1000RO 3.3 I ACKET IGHT...
  • Page 77 6. To turn off the external alarm, click Ext Alarm Cut-Off The external alarm caused by the current faults turns off; new faults will activate the external alarm again. This action does not clear any alarms. PL-1000RO 3.3 I ACKET IGHT ETWORKS NSTALLATION AND...

  • Page 78: Events Tab

    The fields are read only and explained in the following table. The color of the event background indicates the severity of the event: Red: Indicates the occurrence of a Critical or Major alarm  PL-1000RO 3.3 I ACKET IGHT ETWORKS NSTALLATION AND...

  • Page 79: Table 16: Events Tab Parameters

    Note Information related to the event. S.A.: The event is service affecting. • Blank: The event is not service affecting. • Other: Information related to the event. PL-1000RO 3.3 I ACKET IGHT ETWORKS NSTALLATION AND ONFIGURATION ANUAL ONFIDENTIAL AND ROPRIETARY...

  • Page 80: Configuration Changes Tab

    2. Click Start Refresh. The information is automatically updated after the specified number of seconds. 4. To refresh the Fault display manually, click Refresh The information is updated immediately. PL-1000RO 3.3 I ACKET IGHT ETWORKS NSTALLATION AND ONFIGURATION ANUAL ONFIDENTIAL AND...

  • Page 81: Management Port Faults

    Fault display • Event Log tab: View the Event Log, export the log to a file, set the refresh rate, and stop the automatic refresh of the Fault display PL-1000RO 3.3 I ACKET IGHT ETWORKS NSTALLATION AND ONFIGURATION...

  • Page 82: Alarms Tab

     Yellow: Minor alarm  The LED display reflects the actual LED indications on the unit. For the list of LEDs and their functions, see Technical Specifications (p. 13). PL-1000RO 3.3 I ACKET IGHT ETWORKS NSTALLATION AND ONFIGURATION ANUAL ONFIDENTIAL AND...

  • Page 83: Table 18: Alarms Tab Parameters

    The type of alarm. • Note Whether or not the alarm is service S.A.: The alarm is service affecting. affecting. • Blank: The alarm is not service affecting. PL-1000RO 3.3 I ACKET IGHT ETWORKS NSTALLATION AND ONFIGURATION ANUAL ONFIDENTIAL AND ROPRIETARY...

  • Page 84: Events Tab

    1. Click Export File The Opening table.csv dialog box appears. 2. Click Save File. 3. Click OK. 3. To set the refresh rate of the Fault display: PL-1000RO 3.3 I ACKET IGHT ETWORKS NSTALLATION AND ONFIGURATION ANUAL ONFIDENTIAL AND ROPRIETARY...

  • Page 85: Configuration Changes Tab

    S.A.: The event is service affecting. • Blank: The event is not service affecting. • Other: Information related to the event. 5.6.3 Configuration Changes Tab Figure 44: Configuration Changes Tab PL-1000RO 3.3 I ACKET IGHT ETWORKS NSTALLATION AND ONFIGURATION ANUAL ONFIDENTIAL AND ROPRIETARY NFORMATION...

  • Page 86: Table 20: Configuration Changes Tab Parameters

    The entity that caused the change. Severity The severity of the change. Critical, Major, Minor, Cleared, Event Message The type of change. Note Information related to the change. PL-1000RO 3.3 I ACKET IGHT ETWORKS NSTALLATION AND ONFIGURATION ANUAL ONFIDENTIAL AND...

  • Page 87: Ethernet Port Faults

    Fault display To open the Ethernet Port Fault window: 1. Click Fault. 2. Click Ethernet to select the Ethernet port. The Ethernet Port Fault window opens. PL-1000RO 3.3 I ACKET IGHT ETWORKS NSTALLATION AND ONFIGURATION ANUAL ONFIDENTIAL AND...

  • Page 88: Alarms Tab

    2. To export the list of alarms to a file: 1. Click Export to File The Opening table.csv dialog box appears. 2. Click Save File. 3. Click OK. PL-1000RO 3.3 I ACKET IGHT ETWORKS NSTALLATION AND ONFIGURATION ANUAL ONFIDENTIAL AND...

  • Page 89: Table 21: Alarms Tab Parameters

    The type of alarm. • Note Whether or not the alarm is service S.A.: The alarm is service affecting. affecting. • Blank: The alarm is not service affecting. PL-1000RO 3.3 I ACKET IGHT ETWORKS NSTALLATION AND ONFIGURATION ANUAL ONFIDENTIAL AND ROPRIETARY...

  • Page 90: Events Tab

    1. Click Export File The Opening table.csv dialog box appears. 2. Click Save File. 3. Click OK. 3. To set the refresh rate of the Fault display: PL-1000RO 3.3 I ACKET IGHT ETWORKS NSTALLATION AND ONFIGURATION ANUAL ONFIDENTIAL AND ROPRIETARY...

  • Page 91: Configuration Changes Tab

    S.A.: The event is service affecting. • Blank: The event is not service affecting. • Other: Information related to the event. 5.7.3 Configuration Changes Tab Figure 48: Configuration Changes Tab PL-1000RO 3.3 I ACKET IGHT ETWORKS NSTALLATION AND ONFIGURATION ANUAL ONFIDENTIAL AND ROPRIETARY NFORMATION...

  • Page 92: Table 23: Configuration Changes Tab Parameters

    The entity that caused the change. Severity The severity of the change. Critical, Major, Minor, Cleared, Event Message The type of change. Note Information related to the change. PL-1000RO 3.3 I ACKET IGHT ETWORKS NSTALLATION AND ONFIGURATION ANUAL ONFIDENTIAL AND...

  • Page 93: Edfa Faults

    Fault display To open the EDFA Fault window: 1. Click Fault. 2. Click an button to select the EDFA module. EDFA The appropriate EDFA Fault window opens. PL-1000RO 3.3 I ACKET IGHT ETWORKS NSTALLATION AND ONFIGURATION ANUAL ONFIDENTIAL AND...

  • Page 94: Alarms Tab

    2. To export the list of alarms to a file: 1. Click Export to File The Opening table.csv dialog box appears. 2. Click Save File. 3. Click OK. PL-1000RO 3.3 I ACKET IGHT ETWORKS NSTALLATION AND ONFIGURATION ANUAL ONFIDENTIAL AND...

  • Page 95: Table 24: Alarms Tab Parameters

    The type of alarm. • Note Whether or not the alarm is service S.A.: The alarm is service affecting. affecting. • Blank: The alarm is not service affecting. PL-1000RO 3.3 I ACKET IGHT ETWORKS NSTALLATION AND ONFIGURATION ANUAL ONFIDENTIAL AND ROPRIETARY...

  • Page 96: Events Tab

    File. 3. Click OK. 3. To set the refresh rate of the Fault display: 1. In the Refresh every field, type the number of seconds that the window should refresh. PL-1000RO 3.3 I ACKET IGHT ETWORKS NSTALLATION AND ONFIGURATION ANUAL...

  • Page 97: Configuration Changes Tab

    Figure 52: Configuration Changes Tab Use the Configuration Changes tab to view the Configuration Changes Log, export the log to a file, set the refresh rate, and stop the automatic refresh of the Fault display. PL-1000RO 3.3 I ACKET IGHT ETWORKS...

  • Page 98: Table 26: Configuration Changes Tab Parameters

    The entity that caused the change. Severity The severity of the change. Critical, Major, Minor, Cleared, Event Message The type of change. Note Information related to the change. PL-1000RO 3.3 I ACKET IGHT ETWORKS NSTALLATION AND ONFIGURATION ANUAL ONFIDENTIAL AND...

  • Page 99: Psu Faults

    Fault display To open the PSU Fault window: 1. Click Fault. 2. Click a button to select the PSU. The appropriate PSU Fault window opens. PL-1000RO 3.3 I ACKET IGHT ETWORKS NSTALLATION AND ONFIGURATION ANUAL ONFIDENTIAL AND...

  • Page 100: Alarms Tab

    2. To export the list of alarms to a file: 1. Click Export to File The Opening table.csv dialog box appears. 2. Click Save File. 3. Click OK. PL-1000RO 3.3 I ACKET IGHT ETWORKS NSTALLATION AND ONFIGURATION ANUAL ONFIDENTIAL AND...

  • Page 101: Table 27: Alarms Tab Parameters

    The type of alarm. • Note Whether or not the alarm is service S.A.: The alarm is service affecting. affecting. • Blank: The alarm is not service affecting. PL-1000RO 3.3 I ACKET IGHT ETWORKS NSTALLATION AND ONFIGURATION ANUAL ONFIDENTIAL AND ROPRIETARY...

  • Page 102: Events Tab

     2. To export the Event Log to a file: 1. Click Export File The Opening table.csv dialog box appears. 2. Click Save File. 3. Click OK. PL-1000RO 3.3 I ACKET IGHT ETWORKS NSTALLATION AND ONFIGURATION ANUAL ONFIDENTIAL AND ROPRIETARY...

  • Page 103: Configuration Changes Tab

    S.A.: The event is service affecting. • Blank: The event is not service affecting. • Other: Information related to the event. 5.9.3 Configuration Changes Tab Figure 56: Configuration Changes Tab PL-1000RO 3.3 I ACKET IGHT ETWORKS NSTALLATION AND ONFIGURATION ANUAL ONFIDENTIAL AND ROPRIETARY NFORMATION...

  • Page 104: Table 29: Configuration Changes Tab Parameters

    The entity that caused the change. Severity The severity of the change. Critical, Major, Minor, Cleared, Event Message The type of change. Note Information related to the change. PL-1000RO 3.3 I ACKET IGHT ETWORKS NSTALLATION AND ONFIGURATION ANUAL ONFIDENTIAL AND...

  • Page 105: Configuration Management

    Configure how the DWDM channels are handled by the WSS module  • MNG Port View port status  Configure port parameters  Enable or disable the port  View SFP information  PL-1000RO 3.3 I ACKET IGHT ETWORKS NSTALLATION AND ONFIGURATION ANUAL ONFIDENTIAL AND ROPRIETARY NFORMATION LL RIGHTS RESERVED...

  • Page 106: General Configuration Procedure

    PSU Configuration (p. 121))  (see FAN Unit Information (p. 123))  The appropriate Configuration window opens. 3. Click a tab. The appropriate tab opens. PL-1000RO 3.3 I ACKET IGHT ETWORKS NSTALLATION AND ONFIGURATION ANUAL ONFIDENTIAL AND ROPRIETARY NFORMATION LL RIGHTS RESERVED...

  • Page 107: System Configuration

    Configure SNMP parameters and traps • SNMP • Syslog tab: Configure Syslog servers To open the System Configuration window: 1. Click Configuration. 2. Click System. The System Configuration window opens. PL-1000RO 3.3 I ACKET IGHT ETWORKS NSTALLATION AND ONFIGURATION ANUAL ONFIDENTIAL AND ROPRIETARY NFORMATION...

  • Page 108: General Tab

    Up Time The system uptime. This shows how Elapsed time much time passed since last reset. System Temperature The measured temperature of the Celsius system. PL-1000RO 3.3 I ACKET IGHT ETWORKS NSTALLATION AND ONFIGURATION ANUAL ONFIDENTIAL AND ROPRIETARY NFORMATION...
  • Page 109 The time from no defect detection till 2.5-10 seconds Time report, if defect is still constantly not Default: 10 seconds detected. Recommended to use the default time. PL-1000RO 3.3 I ACKET IGHT ETWORKS NSTALLATION AND ONFIGURATION ANUAL ONFIDENTIAL AND ROPRIETARY...

  • Page 110: Inventory Tab

    The serial number of the component. Hardware Rev The hardware revision of the component. Part Number The part number of the component. Manufacturer The manufacturer of the component. PL-1000RO 3.3 I ACKET IGHT ETWORKS NSTALLATION AND ONFIGURATION ANUAL ONFIDENTIAL AND...

  • Page 111: License Tab

    IP route to the defined server. Therefore, you may want to add the Time Server address to the Static Routing table (see IP Tab (p. 99)). To configure SNTP: 1. Click the Time tab. PL-1000RO 3.3 I ACKET IGHT ETWORKS NSTALLATION AND ONFIGURATION ANUAL ONFIDENTIAL AND ROPRIETARY NFORMATION...

  • Page 112: Table 32: Time Tab Parameters

    • Connected: The link to the server has been established. • Disconnected: No link to the server. This field is read only. PL-1000RO 3.3 I ACKET IGHT ETWORKS NSTALLATION AND ONFIGURATION ANUAL ONFIDENTIAL AND ROPRIETARY...

  • Page 113: Ip Tab

    ONFIGURATION ANAGEMENT 6.3.5 IP Tab Figure 62: IP Tab - Dual Networks PL-1000RO 3.3 I ACKET IGHT ETWORKS NSTALLATION AND ONFIGURATION ANUAL ONFIDENTIAL AND ROPRIETARY NFORMATION LL RIGHTS RESERVED...
  • Page 114  When configuring IP addresses, make sure that the IP address of the OSC/In-band is not in the same subnet as the LAN port, otherwise the routing of the management traffic will fail. PL-1000RO 3.3 I ACKET IGHT ETWORKS...

  • Page 115: Table 33: Ip Tab Parameters

    For example: 10.0.11.34 This field is read only when  is set to Network Mode Single Network. The same IP address applies  to both MNG ports. PL-1000RO 3.3 I ACKET IGHT ETWORKS NSTALLATION AND ONFIGURATION ANUAL ONFIDENTIAL AND ROPRIETARY NFORMATION...

  • Page 116: Snmp Tab

    Figure 65: SNMP Tab Use the SNMP tab to configure the SNMP configuration and traps. ARNING  Changing the community strings may immediately affect the access of the current SNMP session. PL-1000RO 3.3 I ACKET IGHT ETWORKS NSTALLATION AND ONFIGURATION...

  • Page 117: Table 34: Snmp Tab Parameters

    The SNMP trap format. SNMPV2c, SNMPV1 Default: SNMPV2c Community The community string of the public (default) traps. Trap Port The UDP port number. 162 (default) PL-1000RO 3.3 I ACKET IGHT ETWORKS NSTALLATION AND ONFIGURATION ANUAL ONFIDENTIAL AND ROPRIETARY NFORMATION LL RIGHTS RESERVED...

  • Page 118: Syslog Tab

    2. Click Add. The following confirmation message appears. Figure 67: Confirm Configuration 3. Click OK. 3. To remove a configured Syslog server: 1. Click in the corresponding line. Delete PL-1000RO 3.3 I ACKET IGHT ETWORKS NSTALLATION AND ONFIGURATION ANUAL ONFIDENTIAL AND...

  • Page 119: Wss Configuration

    The supported message filter level. Traps: Traps only • Log: Log messages • Debug: Log and debug messages Default: Traps WSS Configuration Figure 69: WSS Configuration Window PL-1000RO 3.3 I ACKET IGHT ETWORKS NSTALLATION AND ONFIGURATION ANUAL ONFIDENTIAL AND ROPRIETARY...

  • Page 120: General Tab

    To configure general WSS parameters: 1. Click the tab. General The General tab opens displaying the general WSS configuration. 2. Fill in the fields as explained in the following table. 3. Click Apply. PL-1000RO 3.3 I ACKET IGHT ETWORKS NSTALLATION AND ONFIGURATION ANUAL...

  • Page 121: Provisioning Tab

    This field is displayed equalization. and applied only if Equalization Method is set to Manual. 6.4.2 Provisioning Tab Figure 71: Provisioning Tab PL-1000RO 3.3 I ACKET IGHT ETWORKS NSTALLATION AND ONFIGURATION ANUAL ONFIDENTIAL AND ROPRIETARY NFORMATION...

  • Page 122: Table 37: Provisioning Tab Parameters

    Wavelength The wavelength of the channel. Units: nanometers (nm) Add/Drop Channel is locally used. Express Channel is locally bypassed. Not Used Channel is unused. Default PL-1000RO 3.3 I ACKET IGHT ETWORKS NSTALLATION AND ONFIGURATION ANUAL ONFIDENTIAL AND ROPRIETARY NFORMATION LL RIGHTS RESERVED...

  • Page 123: Management Port Configuration

    Configure ALS for an MNG port To open the Management Port Configuration window: 1. Click Configuration. 2. Click an button to select the management port. The appropriate Management Port Configuration window opens. PL-1000RO 3.3 I ACKET IGHT ETWORKS NSTALLATION AND ONFIGURATION...

  • Page 124: Mng Tab

    The selected port is enabled, the button is disabled, and the Admin Up button is enabled. Admin Down 5. To disable the port: 1. Click Admin Down PL-1000RO 3.3 I ACKET IGHT ETWORKS NSTALLATION AND ONFIGURATION ANUAL ONFIDENTIAL AND ROPRIETARY...

  • Page 125: Table 38: Mng Tab Parameters

    Admin the port. Down Service Type The management type. Fast Ethernet (default) Port Alias The logical name given to the port Free text for identification purposes. PL-1000RO 3.3 I ACKET IGHT ETWORKS NSTALLATION AND ONFIGURATION ANUAL ONFIDENTIAL AND ROPRIETARY NFORMATION...

  • Page 126: Sfp Tab

    String Serial Number The serial number of the SFP. String • WDM Channel Spacing The channel spacing of the SFP. CWDM: nm • DWDM: GHz PL-1000RO 3.3 I ACKET IGHT ETWORKS NSTALLATION AND ONFIGURATION ANUAL ONFIDENTIAL AND ROPRIETARY NFORMATION LL RIGHTS RESERVED...

  • Page 127: Als Tab

    The default threshold for Low Receiver Threshold Power alarm. Override Low Receiver Power The configured threshold for the Low Alarm Threshold Receiver Power alarm. 6.5.3 ALS Tab Figure 77: ALS Tab PL-1000RO 3.3 I ACKET IGHT ETWORKS NSTALLATION AND ONFIGURATION ANUAL ONFIDENTIAL AND ROPRIETARY NFORMATION...

  • Page 128: Table 40: Als Tab Parameters

    Manual mode only. ALS Manual Restart for Manual restart for test pulse width 90 ± 10 sec Test Pulse (in seconds). Default: 90 sec Manual restart only. PL-1000RO 3.3 I ACKET IGHT ETWORKS NSTALLATION AND ONFIGURATION ANUAL ONFIDENTIAL AND ROPRIETARY...

  • Page 129: Ethernet Port Configuration

    Ethernet Tab Figure 79: Ethernet Tab Use the Ethernet tab to configure the Ethernet port. To configure the Ethernet port: 1. Click to select the Ethernet port. Ethernet PL-1000RO 3.3 I ACKET IGHT ETWORKS NSTALLATION AND ONFIGURATION ANUAL ONFIDENTIAL AND...

  • Page 130: Table 41: Ethernet Tab Parameters

    Full, Half of the Ethernet port. Default: Full This field is applicable only if is disabled. Auto Negotiation Status (Duplex) The actual duplex of the Ethernet port. Full, Half PL-1000RO 3.3 I ACKET IGHT ETWORKS NSTALLATION AND ONFIGURATION ANUAL ONFIDENTIAL AND...

  • Page 131: Mux/Demux Configuration

    To open the MUX/DEMUX Configuration window: 1. Click Configuration. 2. Click to select the MUX/DEMUX module. The MUX/DEMUX Configuration window opens. 6.7.1 MUX/DEMUX Tab Figure 81: MUX/DEMUX Tab PL-1000RO 3.3 I ACKET IGHT ETWORKS NSTALLATION AND ONFIGURATION ANUAL ONFIDENTIAL AND...

  • Page 132: Edfa Configuration

    To open the EDFA Configuration window: 1. Click Configuration. 2. Click an button to select the EDFA module. EDFA The appropriate EDFA Configuration window opens. PL-1000RO 3.3 I ACKET IGHT ETWORKS NSTALLATION AND ONFIGURATION ANUAL ONFIDENTIAL AND...

  • Page 133: Edfa Tab

    The following confirmation message appears. Figure 84: Confirm Changes 2. Click OK. The selected module is enabled, the button is disabled, and the Admin Up Admin Down button is enabled. PL-1000RO 3.3 I ACKET IGHT ETWORKS NSTALLATION AND ONFIGURATION ANUAL ONFIDENTIAL AND...
  • Page 134 The current measured optical power of Power the EDFA. Measured Gain The current measured gain of the EDFA. dB Measured Receive The current measured receive power of Power the EDFA. PL-1000RO 3.3 I ACKET IGHT ETWORKS NSTALLATION AND ONFIGURATION ANUAL ONFIDENTIAL AND ROPRIETARY...

  • Page 135: Psu Configuration

    To open the PSU Configuration window: 1. Click Configuration. 2. Click a button to select the power supply unit. The appropriate PSU Configuration window opens. PL-1000RO 3.3 I ACKET IGHT ETWORKS NSTALLATION AND ONFIGURATION ANUAL...

  • Page 136: Psu Tab

    Down: Alarm is detected power supply unit. Type The type of power supply unit. AC PSU, DC PSU Hardware Revision The hardware version of the power supply dddd unit. PL-1000RO 3.3 I ACKET IGHT ETWORKS NSTALLATION AND ONFIGURATION ANUAL ONFIDENTIAL AND ROPRIETARY...

  • Page 137: Fan Unit Configuration

    To view the FAN unit information: Click to select the FAN unit. • The FAN Unit tab opens displaying the FAN unit information. The fields are read only and explained in the following table. PL-1000RO 3.3 I ACKET IGHT ETWORKS NSTALLATION AND ONFIGURATION...
  • Page 138 Up: Normal operation indicates if there is a failure in the FAN unit. • Down: Alarm is detected Hardware Revision The hardware version of the FAN unit. dddd PL-1000RO 3.3 I ACKET IGHT ETWORKS NSTALLATION AND ONFIGURATION ANUAL ONFIDENTIAL AND...
  • Page 139 ONFIGURATION ANAGEMENT Chapter PL-1000RO 3.3 I ACKET IGHT ETWORKS NSTALLATION AND ONFIGURATION ANUAL ONFIDENTIAL AND ROPRIETARY NFORMATION LL RIGHTS RESERVED...

  • Page 140: Performance Monitoring

    Use the System Optical Information window to view optical performance of all optical modules installed in the system. To open the System Optical Information window: 1. Click Performance. 2. Click System. The Optical Information window opens. PL-1000RO 3.3 I ACKET IGHT ETWORKS NSTALLATION AND ONFIGURATION...

  • Page 141: Optical Information Tab

     Vendor The manufacturer of the optical module. Type The type of optical module. Wavelength The Tx wavelength (nm). Tx Power The current measured Tx power. PL-1000RO 3.3 I ACKET IGHT ETWORKS NSTALLATION AND ONFIGURATION ANUAL ONFIDENTIAL AND ROPRIETARY NFORMATION...

  • Page 142: Wss Monitoring

    Use the WSS Monitoring window to view optical performance of the optical channels handled by the WSS module. To open the WSS Monitoring window: 1. Click Performance. 2. Click WSS. The WSS Monitoring window opens. PL-1000RO 3.3 I ACKET IGHT ETWORKS NSTALLATION AND ONFIGURATION...

  • Page 143: Wss Monitoring Tab

    Optical power level: Displayed only for channels configured as add/drop or express. • LOS: Displayed only if the optical power of the channel is below the threshold (lower than -30 dBm). PL-1000RO 3.3 I ACKET IGHT ETWORKS NSTALLATION AND ONFIGURATION...

  • Page 144: Management Port Performance Monitoring

    To open the Management Port Performance Monitoring window: 1. Click Performance. 2. Click an button to select the management port. The appropriate Management Port Performance Monitoring window opens. PL-1000RO 3.3 I ACKET IGHT ETWORKS NSTALLATION AND ONFIGURATION...

  • Page 145: Viewing Optical Performance Monitoring

    The optical level counters are updated. 5. To export the optical level information to a file: 1. Click Export to File The Opening table.csv dialog box appears. 2. Click Save File. PL-1000RO 3.3 I ACKET IGHT ETWORKS NSTALLATION AND ONFIGURATION ANUAL ONFIDENTIAL AND...
  • Page 146 • Previous Day: The date and 00:00 AM of the previous day is displayed in the last row of the table. PL-1000RO 3.3 I ACKET IGHT ETWORKS NSTALLATION AND ONFIGURATION ANUAL...

  • Page 147: Edfa Performance Monitoring

    00:00 AM of the previous day is displayed in the last row of the table. EDFA Performance Monitoring Figure 96: EDFA Performance Monitoring Window button is enabled only if an EDFA module is installed. EDFA PL-1000RO 3.3 I ACKET IGHT ETWORKS NSTALLATION AND ONFIGURATION...

  • Page 148: Viewing Optical Performance Monitoring

    The counters are read only. 2. From the drop-down list, select the interval. PM Period 3. From the drop-down list, select Type Optical Level. PL-1000RO 3.3 I ACKET IGHT ETWORKS NSTALLATION AND ONFIGURATION ANUAL ONFIDENTIAL AND ROPRIETARY NFORMATION...
  • Page 149 Description Format/Values PM Period The interval for averaging the 15 Minutes, Days measured Rx power. Type The type of performance Optical Level monitoring. PL-1000RO 3.3 I ACKET IGHT ETWORKS NSTALLATION AND ONFIGURATION ANUAL ONFIDENTIAL AND ROPRIETARY NFORMATION LL RIGHTS RESERVED...
  • Page 150 • Day: The average of the Previous measured Rx power during the 24 hours since 00:00 AM of the previous day is displayed in the last row of the table. PL-1000RO 3.3 I ACKET IGHT ETWORKS NSTALLATION AND ONFIGURATION ANUAL...

  • Page 151: Maintenance

    Download and activate a new software version • Software To open the System Maintenance window: 1. Click Maintenance. 2. Click System. The System Maintenance window opens. PL-1000RO 3.3 I ACKET IGHT ETWORKS NSTALLATION AND ONFIGURATION ANUAL ONFIDENTIAL AND...

  • Page 152: Restart Tab

    The following confirmation message appears. Figure 100: Confirm Changes 2. Click OK. The software and hardware are reloaded and the system restarts. Traffic goes down for a short period of time. PL-1000RO 3.3 I ACKET IGHT ETWORKS NSTALLATION AND ONFIGURATION...

  • Page 153: Log Files Tab

    Traffic is affected. 8.1.2 Log Files Tab Figure 103: Log Files Tab Use the Log Files tab to view and save System Log files. PL-1000RO 3.3 I ACKET IGHT ETWORKS NSTALLATION AND ONFIGURATION...
  • Page 154 The System Log files are displayed. 3. To save the log data, copy the displayed text from the browser window, paste it into a file, and then save the file. Figure 104: System Log Files (Example) PL-1000RO 3.3 I ACKET IGHT ETWORKS...

  • Page 155: Configuration Tab

     The format of the saved configuration is a text file. However, changing the content of this file manually is not allowed. To upload system configuration: 1. Click the Configuration tab. The Configuration tab opens. 2. Click Upload System Configuration PL-1000RO 3.3 I ACKET IGHT ETWORKS NSTALLATION AND ONFIGURATION ANUAL ONFIDENTIAL AND ROPRIETARY...
  • Page 156 Configuration The Configuration tab opens 2. In the field, type the full path of the file or click Configuration File Browse and browse to the file location. PL-1000RO 3.3 I ACKET IGHT ETWORKS NSTALLATION AND ONFIGURATION ANUAL ONFIDENTIAL AND...
  • Page 157 Update Configuration and Restart The following confirmation message appears. Figure 108: Confirm System Overwrite 5. Click OK. The following update message appears and the node is rebooted. Figure 109: System Updating and Restarting Message PL-1000RO 3.3 I ACKET IGHT ETWORKS NSTALLATION AND ONFIGURATION...

  • Page 158: Software Tab

    2. In the field, type the full path of the file or click Distribution Directory Browse and browse to the file location. For example: pl.vx 3. Click Download PL-1000RO 3.3 I ACKET IGHT ETWORKS NSTALLATION AND ONFIGURATION ANUAL ONFIDENTIAL AND...
  • Page 159 2. To perform a switch and cold restart: 1. Click Switch & Cold Restart The following confirmation message appears. Figure 113: Confirm Changes PL-1000RO 3.3 I ACKET IGHT ETWORKS NSTALLATION AND ONFIGURATION ANUAL...

  • Page 160: External Alarm Maintenance

    The software version is switched, the software is reloaded and restarted, and the new version is activated. Traffic is not affected. External Alarm Maintenance Figure 115: External Alarm Maintenance Window Use the External Alarm Maintenance window to configure the external alarm. PL-1000RO 3.3 I ACKET IGHT ETWORKS NSTALLATION AND ONFIGURATION...

  • Page 161: External Alarm Maintenance Tab

    The severity of the External Input Alarm. Critical, Major, Minor, Notification Alarm Activity Used to disable the Input External Alarm. Disable, Enable Alarm Polarity Determines the polarity of the Input Dry Normally Close, Normally Open Contact. PL-1000RO 3.3 I ACKET IGHT ETWORKS NSTALLATION AND ONFIGURATION ANUAL...

  • Page 163: Topology Management

    Use the Network Topology window to view the network topology and define multiple nodes as multi-chassis. To open the Network Topology window: Click Topology. • The Network Topology window opens. PL-1000RO 3.3 I ACKET IGHT ETWORKS NSTALLATION AND ONFIGURATION ANUAL...

  • Page 164: Network Topology Tab

    Use the Network Topology tab to view the topology. To view the network topology: Click the tab. • Network Topology The Network Topology tab opens displaying the PL-1000RO nodes connected together with the OSC channel. PL-1000RO 3.3 I ACKET IGHT ETWORKS NSTALLATION AND ONFIGURATION ANUAL ONFIDENTIAL AND...
  • Page 165 OPOLOGY ANAGEMENT 9.1.1.1 Network Linear Topology The following figure is an example of a linear topology. Figure 119: Linear Topology (Example) PL-1000RO 3.3 I ACKET IGHT ETWORKS NSTALLATION AND ONFIGURATION ANUAL ONFIDENTIAL AND ROPRIETARY NFORMATION LL RIGHTS RESERVED...
  • Page 166 The alarm status of each node is marked by the color of the box around the node: Green: No Major alarms on the node • Red: Major alarms on the node • PL-1000RO 3.3 I ACKET IGHT ETWORKS NSTALLATION AND...

  • Page 167: Zooming In And Out Of The Topology Display

    Defining Multiple Nodes as Multi-Chassis When multiple PL-1000RO nodes are located at the same site, you can define them as multi-chassis. The Chassis ID number must be the same for each node. PL-1000RO 3.3 I ACKET IGHT ETWORKS NSTALLATION AND...
  • Page 168 The General tab opens. Figure 121: General Tab 5. In the Chassis ID field, type the number. 6. Click Apply. 7. Repeat these steps for each node. PL-1000RO 3.3 I ACKET IGHT ETWORKS NSTALLATION AND ONFIGURATION ANUAL ONFIDENTIAL AND...
  • Page 169 OPOLOGY ANAGEMENT The following figure shows two nodes, in a ring of four, defined as multi-chassis. Figure 122: Multi-Chassis Nodes PL-1000RO 3.3 I ACKET IGHT ETWORKS NSTALLATION AND ONFIGURATION ANUAL ONFIDENTIAL AND ROPRIETARY NFORMATION LL RIGHTS RESERVED...

  • Page 171: Remote Management Configuration

    2. Configure management for PL-1000RO A. 3. Configure management for PL-1000RO B. 4. Access the Web application from Management A to PL-1000RO A. 5. Access the Web application from Management A to PL-1000RO B. PL-1000RO 3.3 I ACKET IGHT ETWORKS...

  • Page 172: Configuring Management For Pl-1000Ro A

    6. (Required only if using an SNMP management system) Configure the SNMP table to send SNMP traps to the two management systems: Traps (see SNMP Tab (p. 102)). PL-1000RO 3.3 I ACKET IGHT ETWORKS NSTALLATION AND ONFIGURATION ANUAL ONFIDENTIAL AND...

  • Page 173: Configuring Management For Pl-1000Ro B

    Address: 11.0.0.96 OSC/In-band IP  Mask: 255.255.0.0 OSC/In-band Subnet  This example assumes that you are working in mode. Dual Network 5. Click Apply. PL-1000RO 3.3 I ACKET IGHT ETWORKS NSTALLATION AND ONFIGURATION ANUAL ONFIDENTIAL AND ROPRIETARY NFORMATION LL RIGHTS RESERVED...
  • Page 174 8. (Required only if using an SNMP management system) Configure the SNMP table to send SNMP traps to the two management systems: Traps (see SNMP Tab (p. 102)). PL-1000RO 3.3 I ACKET IGHT ETWORKS NSTALLATION AND ONFIGURATION ANUAL ONFIDENTIAL AND...

  • Page 175: Accessing The Web Application From Management Ato Pl-1000Ro A

    2. Open the Web browser. 3. In the address field of the browser, type the of the management IP address port of the remote PL-1000RO as follows: http://11.0.0.96 (for HTTP access) PL-1000RO 3.3 I ACKET IGHT ETWORKS NSTALLATION AND ONFIGURATION...

  • Page 176: Accessing The Web Application From Management Bto Pl-1000Ro B

    IP address of the MNG port of PL-1000RO A as follows: http://11.0.0.111 (for HTTP access) https://11.0.0.111 (for HTTP secure access) (as illustrated in Remote Management Configuration Example (p. 157)). PL-1000RO 3.3 I ACKET IGHT ETWORKS NSTALLATION AND ONFIGURATION ANUAL ONFIDENTIAL AND...
  • Page 177 EMOTE ANAGEMENT ONFIGURATION 4. Press Enter. The Login window opens. 5. Log in to the Web application (see Logging In to the Web Application (p. 32)). PL-1000RO 3.3 I ACKET IGHT ETWORKS NSTALLATION AND ONFIGURATION ANUAL ONFIDENTIAL AND ROPRIETARY NFORMATION...

  • Page 179: Cli

    PC with a terminal emulation application. SSH: These methods can be used with an IP connection via • Using Telnet or the local LAN port or remotely via the OSC channel. PL-1000RO 3.3 I ACKET IGHT ETWORKS NSTALLATION AND...

  • Page 180: Using A Serial Port

    Reply from 192.168.3.201: bytes=32 time<1ms TTL=64 Ping statistics for 192.168.3.201: Packets: Sent = 4, Received = 4, Lost = 0 (0% loss), Approximate round trip times in milli-seconds: Minimum = 0ms, Maximum = 0ms, Average = 0ms PL-1000RO 3.3 I ACKET IGHT ETWORKS NSTALLATION AND...

  • Page 181: Using Ssh

    2. After the successful ping, invoke the SSH client. You should specify to the client the IP of the node to which you want to connect. If this is the first time you connect to the node, you will probably see a message similar to the following: PL-1000RO 3.3 I ACKET IGHT ETWORKS...

  • Page 182: Cli Command Types

    • command tree. Ping command • Interface commands • IP Setting commands • Log commands • Show commands • System Restart command • PL-1000RO 3.3 I ACKET IGHT ETWORKS NSTALLATION AND ONFIGURATION ANUAL ONFIDENTIAL AND ROPRIETARY NFORMATION LL RIGHTS RESERVED...

  • Page 183: Running Cli Commands

    Configure Interface EDFA (p. 173)  Configure Interface MNG (p. 174)  IP Setting commands • Configure Interface Ethernet IP (p. 174)  PL-1000RO 3.3 I ACKET IGHT ETWORKS NSTALLATION AND ONFIGURATION ANUAL ONFIDENTIAL AND ROPRIETARY NFORMATION LL RIGHTS RESERVED...

  • Page 184: General Commands

    The same user and password that is used for the Web application is accepted by the CLI. In addition, the CLI checks the user permission properties (Administrator, Read Only, Read-Write) during command execution. These properties are inherited from the Web application. PL-1000RO 3.3 I ACKET IGHT ETWORKS NSTALLATION AND...
  • Page 185 PL-1000RO>>help con int eth ip config interface ethernet ip [<addr> [-n <netmask>] [-g <gateway>]] PL-1000RO>> 11.4.1.4 History Command Command: Description: This command displays the last 20 commands. Example: PL-1000RO>show>>h PL-1000RO 3.3 I ACKET IGHT ETWORKS NSTALLATION AND ONFIGURATION ANUAL ONFIDENTIAL AND ROPRIETARY NFORMATION...

  • Page 186: Ping Command

    Up Command Command: Description: This command takes you up one level in the command tree. Example: PL-1000RO>configure>interface>ethernet>>up PL-1000RO>configure>interface>> 11.4.2 Ping Command Command: ping <ip-address> PL-1000RO 3.3 I ACKET IGHT ETWORKS NSTALLATION AND ONFIGURATION ANUAL ONFIDENTIAL AND ROPRIETARY NFORMATION LL RIGHTS RESERVED...

  • Page 187: Interface Commands

    This command sets the Admin Status of the EDFA to the required value. If the is not specified, the administrative status of the EDFA is Admin Status displayed. PL-1000RO 3.3 I ACKET IGHT ETWORKS NSTALLATION AND ONFIGURATION ANUAL ONFIDENTIAL AND...

  • Page 188: Ip Setting Commands

    If no parameters are specified, the current IP parameter values are displayed. Example: PL-1000RO>configure>interface>ethernet>>ip 10.0.3.200 –n 255.255.0.0 –g 10.0.44.44 PL-1000RO>configure>interface>ethernet>>ip Addr is 10.0.3.200, Subnet mask is 255.255.0.0 Gateway is 10.0.44.44 PL-1000RO>configure>interface>ethernet>> PL-1000RO 3.3 I ACKET IGHT ETWORKS NSTALLATION AND ONFIGURATION ANUAL ONFIDENTIAL AND...
  • Page 189 (LAN port and MNG ports). After changing network mode, you must cold restart the node (see Configure System Reset Command (p. 178)). Example: PL-1000RO>configure>interface>network>>? mode config interface network mode [dual|single] PL-1000RO>configure>interface>network>>mode PL-1000RO 3.3 I ACKET IGHT ETWORKS NSTALLATION AND ONFIGURATION ANUAL ONFIDENTIAL AND ROPRIETARY...

  • Page 190: Log Commands

    Show Commands The following are the Show commands: Show Alarms (p. 177) • Show Events (p. 177) • Show Optics (p. 177) • PL-1000RO 3.3 I ACKET IGHT ETWORKS NSTALLATION AND ONFIGURATION ANUAL ONFIDENTIAL AND ROPRIETARY NFORMATION LL RIGHTS RESERVED...
  • Page 191 This command displays the optical information of the specified entity. The command Show Optics Port is not applicable to the PL-1000RO. Example: PL-1000RO>show optics mng 2 Vendor: Infineon FO GmbH Part Number: V23848-M305-C56W Serial Number: 26572841 PL-1000RO 3.3 I ACKET IGHT ETWORKS NSTALLATION AND ONFIGURATION ANUAL ONFIDENTIAL AND ROPRIETARY...

  • Page 192: System Restart Command

     Performing this command while using Telnet/SSH will terminate the session.  It is recommended to save the old configuration file before restoring to factory defaults. Example (of a Telnet session): PL-1000RO>>configure system reset w PL-1000RO>> Connection to host lost. PL-1000RO 3.3 I ACKET IGHT ETWORKS NSTALLATION AND ONFIGURATION ANUAL...

  • Page 193: Appendix A: Connection Data

    (for example, a buzzer) of the customer. The ALARM connector provides two connectivity methods: Normally Open • Normally Closed • PL-1000RO 3.3 I ACKET IGHT ETWORKS NSTALLATION AND ONFIGURATION ANUAL ONFIDENTIAL AND...
  • Page 194 PPENDIX ONNECTION The connector is wired in accordance with the following table. Figure 130: External ALARM Diagram PL-1000RO 3.3 I ACKET IGHT ETWORKS NSTALLATION AND ONFIGURATION ANUAL ONFIDENTIAL AND ROPRIETARY NFORMATION LL RIGHTS RESERVED...
  • Page 195 Upon a Major alarm event, the internal connection of the pin 9 (ALARM Common) is switched to pin 4 (ALARM Normally Open). ALARM Common Common signal (ALARM2_COM) * The pin will be implemented in a future software release. PL-1000RO 3.3 I ACKET IGHT ETWORKS NSTALLATION AND ONFIGURATION ANUAL...

  • Page 196: Eth Connector

    Table 54: Data Ports Specifications Specification Requirement Fiber Type Single mode Fiber Size 2 mm optical fiber Connector Type LC with protective shutters Port Type Optical ports PL-1000RO 3.3 I ACKET IGHT ETWORKS NSTALLATION AND ONFIGURATION ANUAL ONFIDENTIAL AND ROPRIETARY NFORMATION LL RIGHTS RESERVED...

  • Page 197: Mng Ports

    The following power supply combinations are feasible in the PL-1000RO: One or two AC power supplies • One or two DC power supplies • Both AC and DC PSUs can be used in the same unit. PL-1000RO 3.3 I ACKET IGHT ETWORKS NSTALLATION AND ONFIGURATION...

  • Page 198: Power Connectors

    DC-powered PL-1000RO units: DC power is supplied with a dedicated connector for wiring. The following figure shows how to wire the DC connector (DC power supply only). Figure 131: DC Connector Wiring Diagram PL-1000RO 3.3 I ACKET IGHT ETWORKS NSTALLATION AND...

  • Page 199: Protective Ground Terminal

    The protective ground terminal of the PL-1000RO, located on the rack mount, must be connected to a protective ground. The following figure shows how to wire the ground terminal. Figure 132: Protective Ground Terminal Wiring Diagram PL-1000RO 3.3 I ACKET IGHT ETWORKS...

  • Page 200: Fiber Shelf

    The fiber shelf is an optional tray that can be attached to the PL-1000RO to help you organize the optical fibers. The following figure shows the mechanical details of the fiber shelf. Figure 133: Fiber Shelf Diagram PL-1000RO 3.3 I ACKET IGHT ETWORKS...

  • Page 201: Appendix B: Alarm And Event Messages

    Optics Transmission Fault The transceiver is not transmitting. Replace the optical module. Optics Optics Hardware Failure A hardware fault was detected in the optical module. Replace the optical module. PL-1000RO 3.3 I ACKET IGHT ETWORKS NSTALLATION AND ONFIGURATION ANUAL ONFIDENTIAL AND...
  • Page 202 Closed the EDFA output upon loss of input. Check the EDFA client signals. EDFA EDFA End of Line An EDFA problem. Replace the device. EDFA EDFA Eye Safety Hazard. No fiber is connected to the port. PL-1000RO 3.3 I ACKET IGHT ETWORKS NSTALLATION AND ONFIGURATION ANUAL ONFIDENTIAL AND...

  • Page 203: Configuration Event Messages

    Dying Gasp System Remote Unit Failure A remote unit had a power failure. Software Upgrade System Software Upgrade The Software Upgrade operation has Completed been completed. PL-1000RO 3.3 I ACKET IGHT ETWORKS NSTALLATION AND ONFIGURATION ANUAL ONFIDENTIAL AND ROPRIETARY NFORMATION...
  • Page 205 Set the of the Admin Status PL-1000RO port state PL-1000RO uplink port to Up. 1. Check for optical module alarms. Defective optical module 2. Replace the optical module. PL-1000RO 3.3 I ACKET IGHT ETWORKS NSTALLATION AND ONFIGURATION ANUAL ONFIDENTIAL AND...
  • Page 206 External problem Check the IP configuration of the external equipment (for example, the gateway address) that is connected to the local PL-1000RO LAN port. Defective PL-1000RO Replace the PL-1000RO. PL-1000RO 3.3 I ACKET IGHT ETWORKS NSTALLATION AND ONFIGURATION ANUAL ONFIDENTIAL AND...
  • Page 207 Configure Log Disable Cabling the CONTROL Port • 24 Command • 170, 176 Cabling the Data Ports • 25 Configure Log Enable Command • 170, 176 Cabling the ETH Port • 24 PL-1000RO 3.3 I ACKET IGHT ETWORKS NSTALLATION AND ONFIGURATION ANUAL...
  • Page 208 General Safety Precautions • 19 EDFA Performance Monitoring • General Specifications • 13 General Tab • 94, 106 EDFA Tab • 119 Electrical Safety Precautions • Help Command • 169, 170, 171 PL-1000RO 3.3 I ACKET IGHT ETWORKS NSTALLATION AND ONFIGURATION ANUAL...
  • Page 209 • 182 Management Arc • 152 Other Event Messages • 189 Management Functionality • 12 Overview • 1 Management Port Configuration • 92, 109 Package Contents • 22 PL-1000RO 3.3 I ACKET IGHT ETWORKS NSTALLATION AND ONFIGURATION ANUAL ONFIDENTIAL AND...
  • Page 210 Syslog Tab • 104 Configuration • 157 System Configuration • 92, 93 Remote Management System Faults • 49 Configuration Example • 157, 161, 162 System Maintenance • 137 PL-1000RO 3.3 I ACKET IGHT ETWORKS NSTALLATION AND ONFIGURATION ANUAL ONFIDENTIAL AND...
  • Page 211 Using Telnet • 166 Viewing Optical Performance Monitoring • 131, 134 Web Browser Requirements • Web-based Management • 13 WSS Configuration • 92, 105 WSS Faults • 49, 61 PL-1000RO 3.3 I ACKET IGHT ETWORKS NSTALLATION AND ONFIGURATION ANUAL ONFIDENTIAL AND...

Table of Contents