Advertisement
Quick Links
Advertisement
Summary of Contents for Jetblaster UN1500/12G
- Page 1 Universal Hot Water Pressure Cleaner Manual Universal Manual...
-
Page 2: Table Of Contents
UNIVERSAL INSTRUCTION MANUAL UN1500/12G – UN2400/13G – UN3000/15G – UN3000/21G CONTENTS: PAGE: Safety Set up Instructions 4 – 6 General Maintenance 7 – 8 General Fault Finding 9 – 12 Safeties throughout the Machine 13 – 14 Parts Breakdown... -
Page 3: Safety
SAFETY: Before operating a pressure cleaner please make sure that you read the manual / instructions that is supplied with every unit and make sure that you understand everything that has been read. If you are unsure please re-read the manual / instructions until you understand the entire contents. -
Page 4: Set Up Instructions
SET UP INSTRUCTIONS ITEMS REQUIRED: 1) WATER SUPPLY CONNECTION: a) Water hose with ½” internal bore size 2) ELECTRICAL CONNECTION: a) 3 PHASE OUTLETS FOR THE FOLLOWING CONFIGURATIONS: 2400/13G – 10 AMP 4 PIN PLUG 3000/15G – 20 AMP 4 PIN PLUG 3000/21G –... - Page 5 c) Turn pump switch ON. Ensure that the pump primes itself and settles down to steady operation with a continuous high pressure water flow from nozzles, before turning on the burner. d) If the hot water is required turn ON burner. Burner is equipped with automatic ignition and flame control.
- Page 6 7) IMPORTANT: a) Keep trigger gun open as much as possible. Less SHOTGUNNING (constant pull and release of trigger) ensures longer life of gun, unloader valve, high pressure hose, etc. b) Unit is fitted with a Total Stop control for safety of the machine (this shuts down the machine when not in use after 1-2 minutes), but ALWAYS turn off the unit when not being used.
-
Page 7: General Maintenance
MAINTENANCE & GENERAL INFO IMPORTANT NOTE: When doing maintenance to the pressure cleaner please make sure that the machines on / off switch is in the OFF POSITION, the power to the machine is turned off and the machine is unplugged and that the water to the machine is also turned off and unplugged. - Page 8 FUEL FILTERS: a) Check fuel filter every month and replace if required. BURNER: a) We use a Riello High Efficency Burner with its own inbuilt safeties. The burner unit comes with a phot electric cell, so if there is no fuel in the system there will be no spark and therefore it will not allow the burner to start.
-
Page 9: General Fault Finding
GENERAL FAULT FINDING: Please find below a general fault finding list on the machine. This is to help with any minor problems that may arise with the unit during operation and will help solve that problem quickly and efficiently without too much down time. If any of these faults show up and do not quickly resolve please contact your nearest service provider. - Page 10 7. Nozzle incorrectly 7. Check and replace if sized based on water necessary. flow and PSI. Fluctuating pressure/surging 1. Check all points 1-7 1. Do handlings as above covered above. 2. Lack of water to the 2. Check water to machine.
- Page 11 2. High humidity in air 2. Check and change oil twice as often 3. Piston packing worn 3. Check and replace if necessary Water dripping from under 1. Piston packing worn 1. Check and replace if pump necessary 2. Oring plunger 2.
- Page 12 2. Contact your nearest 2. Coil due for desoot service provider. Unit does not auto stop 1. Pressure switch or 1. Replace pressure flow switch failure switch or flow switch 2. Timer failed 2. Replace timer...
-
Page 13: Safeties Throughout The Machine
SAFETIES THROUGH OUT THE MACHINE: Please find a list of safeties that have been put throughout the machine to help reduce the risk of injury to the operator and also damage to the machine. 1) Riello high efficiency burner with flame sensor – This stops the hot water side of the machine being used without diesel. - Page 14 blowing out flames the cover wouldn’t melt or catch on fire, therefore protecting the rest of machine from being damaged. 10) 2 x Solid Rubber wheels and 2 x Lockable Jockey Wheels – These 2 different types of wheels are used to make the machine easy to move around, which in turn stops the operator of the unit from straining or hurting themselves when moving the machine.
-
Page 15: Parts Breakdown
Please see the below lists of spare parts and machine component breakdowns including the wiring diagram. These can be found on our website at www.jetblaster.com.au in the section of manuals. Each part and wiring diagram is entered separately as listed here. - Page 16 UN3000/21 PUMP WS202 7.5KW NICOLINI MOTOR K7-0 BYPASS UNIVERSAL WIRING DIAGRAM G10 REILLO BURNER...