Advertisement
Quick Links
1.
Introduction ........................................................................................................................... 1
2.
Install LRM001 ..................................................................................................................... 1
3.
Setup LRM001 ...................................................................................................................... 2
4.
AT Command ........................................................................................................................ 5
Appendix : FCC Statement............................................................................................................ 6
Liyatech www.liyatech.com
LRM001- - - - 915
LRM001
LRM001
LRM001
U U U U ser Manual
ser Manual
ser Manual
ser Manual
Version: 1.1
CONTENT
915
915
915
Advertisement
Summary of Contents for Liyatech LRM001-915
-
Page 1: Table Of Contents
LRM001- - - - 915 LRM001 LRM001 U U U U ser Manual ser Manual ser Manual ser Manual Version: 1.1 CONTENT Introduction ........................... 1 Install LRM001 ........................1 Setup LRM001 ........................2 AT Command ........................5 Appendix : FCC Statement......................6 Liyatech www.liyatech.com... -
Page 2: Introduction
M CU . 2. Install LRM001 1. Connect Ipex cable to CN2 915MHz 2. Connect antenna to Ipex cable 3. Connect Micro USB to LRM001 4. Connect USB to your Embedded System LRM001-433 / LRM001-868 LRM001-915 Liyatech Model : LRM001-915... -
Page 3: Setup Lrm001
Please connect LRM001 with PC through micro USB cable. Please install the LoRa antenna to LRM001 3. Setup LRM001 3.1 Use device Open device manager, you will see the COM port, click the COM port, write down COM port number for later use. Liyatech Model : LRM001-915... - Page 4 Download software “Accessport” from http://www.sudt.com/en/ap/download.htm Unzip the file Click “Tools” in menu bar Click “Configuration” 3.8 Key in the Port number “COM 7” which we check in step 1 3.9 Key in the baud rate “57600”. Liyatech Model : LRM001-915...
- Page 5 (See the right circle in following figure.) 3.11 In the “comm window” , Key in “sys reset”. Click “return” (in keyboard) 3.12 Click “Send” 3.13 The “RN2483 1.0.0 Oct 23 2015 14:48:20” will be shown in the 2 line. Liyatech Model : LRM001-915...
-
Page 6: At Command
UART using the ASCII interface. All commands need to be terminated with <CR><LF> and any replies they generate will also be terminated by the same sequence. Noted: All AT commands are case sensitive. Liyatech Model : LRM001-915... -
Page 7: Appendix : Fcc Statement
The outside of final products that contains this module device must display a label referring to the enclosed module. This exterior label can use wording such as the following: “Contains Transmitter Module FCC ID: 2ALXW-LRM001915010” or “Contains FCC ID: 2ALXW-LRM001915010.” Any similar wording that expresses the same meaning may be used. Liyatech Model : LRM001-915... - Page 8 低功率電波輻射性電機管理辦法 第十二條 經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅自變更 頻率、加大功率或變更原設計之特性及功能。 第十四條 低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有干擾現象時，應 立即停用，並改善至無干擾時方得繼續使用。 前項合法通信，指依電信法規定作業之無線電通信。 低功率射頻電機須忍受合法通信或工業、科學及醫療用電波輻射性電機設備之干擾。 Liyatech Model : LRM001-915...