Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for Onlab ONDRIVE ED07
- Page 1 V1.1-ENG ONDRIVE ED07 Automatic Door Controller User Manual www.onlab.com.tr...
- Page 2 All rights reserved. It is prohibited to copy, modify or reproduce the whole or any part of the printed or digital version of this document without the permission of Onlab. Onlab reserves to change or improve any part of this document without prior notice. The latest version of this document can be reached from www.onlab.com.tr...
-
Page 3: Table Of Contents
MOTION PROFILES ........................ 6 Motor Types : ..........................6 CONNECTION TO ELEVATOR CONTROL PANEL ............7 OUTPUT RELAYS AND INPUT SIGNALS MONITORING MENU ........8 LEARNING THE DOOR ......................9 ENCODER MATCHING ......................10 MANUFACTURER SETTINGS ..................... 11 ERROR MESSAGES ....................... 12 www.onlab.com.tr... -
Page 4: General View
Common terminal of “door closed” relay B+ channel of encoder CL2: NO terminal of “door closed” relay B- channel of encoder Z+ channel of encoder Z- channel of encoder *Mechanical dimensions of the product are given in another document on Onlab website. www.onlab.com.tr... -
Page 5: Technical Specifications
Door closed relay (5A @ 250V or 30V Press detected Module error ERROR TYPES Encoder V error High V error Low V error Maximum door speed 80 cm/s -20 ~ +60 °C Operating Temperature EN 12015 / EN 12016 EMC Approval www.onlab.com.tr... -
Page 6: Cable Connections And Properties
: Green : White : Blue : Grey : Pink Cable that will be connected to the INPUT and OUTPUT terminals can be in various lengths that can be adjusted according to the application and place it is mounted. www.onlab.com.tr... -
Page 7: Button Definitions In Inspection Mode And Usage Information
Desired parameter can be selected using DOWN and UP buttons. For getting out “Programming Mode”, ESC button should be pressed in main menu. Then LCD screen shows “Exit ->ENTER” “Return ->ESC”. When ENTER button is pressed, device www.onlab.com.tr... - Page 8 26: Door Type Telescopic Telescopic-Central-Internal Motor 1-Motor 2- Motor 3 (This parameter cannot be modified, 27: Motor Type preprogrammed by Onlab according to the motor type the driver is matched at the production) NORMAL / SOFT CLOSE 28: Working Mode NORMAL...
-
Page 9: User Password Settings
When ordered, Ondrive device will be preprogrammed with the appropriate motor type according to the desired motor option and will be sent to the user with that setting. Motor 1, Motor 2, Motor 3 Detailed mechanical and electrical parameters of the motors can be reached from Onlab website. www.onlab.com.tr... -
Page 10: Connection To Elevator Control Panel
RK: Close the door NO contact 2) Connection with Internal 15V Supply ONDRIVE EIN2 : Photocell contact EIN1 : Nudging contact 1000 (- 24 VDC) (+ 24 VDC) CONTROL PANEL RA: Open the door NO contact RK: Close the door NO contact www.onlab.com.tr... -
Page 11: Output Relays And Input Signals Monitoring Menu
OPEN :- EIN1:- CLOSE:X EIN2:- Similarly, “-” symbol means released for output relays and “X” symbol means operated for output relays. Below an example of LCD screen view for output relays is given: OP RL:- FLT RL:- CL RL:X www.onlab.com.tr... -
Page 12: Learning The Door
“Manufacturer Settings” and change the value of “Motion Direction” parameter in menu 41 to “Inverted”. Then press ESC and ENTER buttons consecutively and return to Inspection mode. At that mode start learning process again by pressing DOWN button. www.onlab.com.tr... -
Page 13: Encoder Matching
Mode. AT that stage, please follow the instructions that are described in LEARNING THE DOOR section. During the production, motor and driver are made as a set and “Encoder Matching” process is done by Onlab. Therefore, users do not need to perform “Encoder Matching” process until they change motor and/or driver electronics. www.onlab.com.tr... -
Page 14: Manufacturer Settings
EN_81_20: Door is opened until the skate is opened completely and it will be stopped. Then, motor is deenergized. 99. Factory Set ? (If this parameter is set, all of the parameter values will be reset to factory settings.) *Factory Setting values can be different in customer specific software. www.onlab.com.tr... -
Page 15: Error Messages
1) Grid voltage can be high. above allowed voltage limit. 2) Deceleration ramps of the door can be very short and steep. Low Vdc Error DC bus voltage decreased 1) Measure the DC bus voltage. below allowed voltage limit. www.onlab.com.tr...