Summary of Contents for Chapman Machinery FM Series
- Page 1 FM Series Flail Mowers All Models Original Instructions Chapman Machinery Ltd, Hele Barton, Week St. Mary, Holsworthy, Devon EX22 6XR Tel: 01288 308149 Email: sales@chapman.co.uk...
-
Page 2: Table Of Contents
The information contained in this manual is correct at the time of going to press. However, in the course of development, changes in specification are inevitable. Should you find the information given differs from your machine, please contact Chapman Machinery Ltd direct for advice. Use only Chapman Genuine Service Parts on Chapman Machinery and Machines. -
Page 3: Hse Information
HSE Information Safe use of all-terrain vehicles (ATVs) in agriculture and forestry – AIS Sheet 33 Introduction Remember that your ability to control the ATV by your body movements will be considerably reduced when carrying a load or This information sheet gives advice on the safe use of ATVs. It covers towing a trailer. -
Page 4: Important Safety Information
Important Safety Information Always read this manual before fitting or operating the machine – whenever any doubt exists contact your dealer or the Chapman Machinery Service Department for advice and assistance. DEFINITIONS The following definitions apply throughout this manual: WARNING - An operating procedure, technique etc., which can result in personal injury or loss of life if not observed carefully. -
Page 5: Transportation Safety
- find the cause of the vibration and eliminate it before using the machine again. Description The FM Series of flail mowers are designed as self-powered units to be towed behind a suitable, ATV, UTV, 4X4, compact tractor or lawn tractor towing vehicles. Designed for vegetation management of paddocks, fields and parkland, the FM series can handle material up to small saplings and brush. -
Page 6: Technical Information
Technical Information Component Identification EMERGENCY STOP CONTROL MUST BE WITHIN REACH OF THE OPERATOR DURING NORMAL USE ENSURE CONTROL EQUIPMENT IS SECURELY ATTACHED TO THE TOWING VEHICLE BEFORE USE CHECK OPERATION OF EMERGENCY STOP CONTROL BEFORE COMMENCING WORK Page 6... -
Page 7: Identification
Identification Each machine is fitted with a serial plate (shown below) which details the following: Model Date of Manufacture (DOM) Serial Number Mass When enquiring regarding spares or additional equipment, ensure you have this information to hand. Implement Decals If your implement does not contain all of the decals shown below, please contact your equipment supplier for replacement decals before use. -
Page 8: Attachment
Attachment Before Attaching the Machine Before attachment, ALWAYS ensure the following: • All safety guards & decals are in good working order and correctly fitted • All blades are correctly fitted, undamaged, and not worn to excess • Lubrication points have been lubricated as per scheduled maintenance period •... -
Page 9: Operating Limits
Operating Limits Minimum / Maximum Ambient Temperature: -15°C /40°C Minimum / Maximum Altitude: 0 meters / 1500 meters * Maximum Inclination: 20° in any direction *Adjustment to carburetor jet size above 1500m will allow operation above this level, please call for advice. -
Page 10: Offsetting
Offsetting If required, the drawbar on the FM Series can be offset to the left or right or folded for storage. The machine is offset by unscrewing the T-bar as shown below. The drawbar can then be moved to the desired location, and the T-bar replaced in a suitable hole. The T-bar must be tightened firmly to prevent movement of the drawbar and should be checked periodically for tightness. -
Page 11: Drive Belts & Power Transmission
Drive Belts & Power Transmission The FM Series Flail Mowers utilize two drive belts (2 x BX41 / 16 X 1115), driven through a centrifugal clutch, with a spring tensioned idler system to compensate for wear of the belts and pulleys. -
Page 12: Maintenance
Maintenance All maintenance, cleaning and repair operations must be performed with the machine suitably supported, the engine switched off (and cool), and the ignition keys removed. NOTE: For commercial use, log hours of operation in a maintenance booklet to ensure proper maintenance intervals and continued service. -
Page 13: Maintenance Instructions
Maintenance Instructions Grease Points All Models: Lubricate the following points using Multi-purpose lithium-based grease with NLGI 2 viscosity grease as per the maintenance schedule: Driven Side Rotor Bearing Non-Driven Side Rotor Bearing Centre-mounted engines only: Page 13... -
Page 14: Flail Condition & Replacement
Check bolts & tighten as necessary Damaged components Repair or replace Excessive Engine Noise Worn muffler repair or replace Engine problems Consult authorized dealer or Chapman Machinery Excessive Belt Noise Belts slipping Adjust belt tensioner Belts worn Replace belts Vibration Worn, bent or broken flails... -
Page 15: Warranty
The Chapman warranty be transferred to a subsequent owner of the machinery (for use within the UK only) for the balance of the warranty period subject to all of the stated warranty conditions and provided that the Change of Owner form is completed and sent to Chapman Machinery within 14 days of change of owner- ship. - Page 16 Hele Barton Week St. Mary Holsworthy Devon EX22 6XR The Products Covered by this Declaration Product: FM Series Flail Mowers & Options Standards and Regulations used: Machinery Directive 2006/42/EC Place of Issue: United Kingdom Name of Representative: James Chapman Position of representative:...