Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for OnTruss EventBoard Basic Series
- Page 1 User manual EventBoard Basic / Premium Acessory parts: TrussClip TrussClip Safety GripSlat BoardBinder BoardBinder ReleaseTool ENGLISH Version: 17.02.2020 / F OnTruss Prinz Gewerbepark - Halle 78 Bozener Str. 1 86165 Augsburg / GERMANY 1 von 27...
-
Page 2: Table Of Contents
Perspective ................................. 10 EventBoard - Types ..............................11 Truss assembly ................................. 12 Mounting the TrussClips – Thanks’ to OnTruss concept................ 13 Mounting the EventBoards on trusses ...................... 16 Locking the EventBoard on the truss ......................20 Integration into a roof construction ......................21 Disassembly ................................ -
Page 3: Introduction
You made a good choice with OnTruss EventBoard. These instructions apply to all OnTruss EventBoards of series Basic and Premium with a length of 50cm, 100cm and 200cm. We also describe how to use the EventBoard Corners C90A, C90C, C45A and C90I. -
Page 4: Technical Data
SET with 50 pcs. 170g Single part BoardBinder 100mm x 24mm x 20mm SET with 2 pcs. BoardBinder Single part 162mm x 140mm x 14,5mm 252g ReleaseTool OnTruss Prinz Gewerbepark - Halle 78 Bozener Str. 1 86165 Augsburg / GERMANY 4 von 27... - Page 5 - two large accessory compartment (one of them with sections) Example of a possible room layout: - 12x EventBoard S200 - 8x EventBoard S200 + 4x EventBoard S100 + 6x EventBoard Corner C90A OnTruss Prinz Gewerbepark - Halle 78 Bozener Str. 1 86165 Augsburg / GERMANY...
- Page 6 (regular dry wiping required) 0°C … 40°C Operation Environment rel. humidity: 25% … 80% 15°C … 35°C Storage Environment rel. humidity: 20% … 75% OnTruss Prinz Gewerbepark - Halle 78 Bozener Str. 1 86165 Augsburg / GERMANY 6 von 27...
- Page 7 Class SR2 Smoke emission (according to DIN 54837) Class ST 2 Dropping (according to DIN 54837) * Further color variants are available on request. OnTruss Prinz Gewerbepark - Halle 78 Bozener Str. 1 86165 Augsburg / GERMANY 7 von 27...
-
Page 8: Safety Instructions
3. Safety instructions Stability is only guaranteed if the original OnTruss accessories are used. Please check each part for perfect condition before use. Our system uses event trusses of other manufacturers as substructure. Therefore please check the condition of your trusses. All pipes must not be bent or damaged. -
Page 9: Basics
EventBoard is a useful extension to your existing truss system. The following description refer to 4-point trusses as basic structure. Our system is especially designed for this type of truss. OnTruss Prinz Gewerbepark - Halle 78 Bozener Str. 1... -
Page 10: Unpacking The Product
Here is an example: This man is standing on the staff side. The audience is looking to the counter. You can also recognize the front edge by the two parallel rails which are directly next to each other. OnTruss Prinz Gewerbepark - Halle 78 Bozener Str. -
Page 11: Eventboard - Types
All corner boards are suitable for box corners and truss corners. It only depends on the grid of your substructure which corner you can use. In the next chapter we explain which aspects are important to pay attention to. OnTruss Prinz Gewerbepark - Halle 78 Bozener Str. 1... -
Page 12: Truss Assembly
The basic rule is that a truss must be located under all EventBoard elements (straight or corner). In most cases the corner is placed after a straight element (S050 / S100 / S200). Of course you can also connect two 45° corners (C45A) directly with each other. OnTruss Prinz Gewerbepark - Halle 78 Bozener Str. 1... -
Page 13: Mounting The Trussclips - Thanks' To Ontruss Concept
9. Mounting the TrussClips – Thanks’ to OnTruss concept. Before placing the EventBoard on truss, you have to mount our TrussClips. This part couples the EventBoard on the truss. We carry the TrussClip as a separate accessory. You can get multiple clips in a SET from your dealer. - Page 14 If the furniture consists only of corners or the furniture ends with a corner, we recommend using up to 4 TrussClips. To do this, attach the TrussClips to the short rails that are normally reserved for the BoardBinder. A simple furniture could be a table for example. OnTruss Prinz Gewerbepark - Halle 78 Bozener Str.
- Page 15 Please check when you put on the next board that the TrussClips really fits. If you have placed truss segments in your substructure, it is quite possible that you have to move a few TrussClips again. OnTruss Prinz Gewerbepark - Halle 78 Bozener Str.
-
Page 16: Mounting The Eventboards On Trusses
C90A. Please check that both BoardBinders (#2) are inserted in the rails at the corner piece. They must be in the rest position. The BoardBinders and GripSlats are available as separate accessories. OnTruss Prinz Gewerbepark - Halle 78 Bozener Str. 1... - Page 17 Info: For easier handling of the BoardBinder you can use the BoardBinder ReleaseTool for other purposes. Insert the tool at a slight angle to the intermediate position (imprinted with a short line) and then move the BoardBinder at this angle. OnTruss Prinz Gewerbepark - Halle 78 Bozener Str.
- Page 18 This is the way you proceed with all straight boards. Make sure that the transition between each plate is flush at the end of your work. Ensure that there is no gap between the boards. OnTruss Prinz Gewerbepark - Halle 78 Bozener Str.
- Page 19 C90A. This is the position of both BoardBinders when the end piece C90A is connected safely. Finally, fasten the end piece C90A on the truss using the Velcro tapes. OnTruss Prinz Gewerbepark - Halle 78 Bozener Str. 1...
-
Page 20: Locking The Eventboard On The Truss
Especially on short distances you have to install TrussClip Safety’s! Due to the smaller number of attachments and the simple shape, the boards are generally easier to remove. That’s exactly what you prevent with the safety clips. OnTruss Prinz Gewerbepark - Halle 78 Bozener Str. 1... -
Page 21: Integration Into A Roof Construction
You also have the option to attach the pipes at the front side (audience area) of the counter. The EventBoard protrudes only so much that a vertical pipe can be attached with double clamps (100kg). OnTruss Prinz Gewerbepark - Halle 78 Bozener Str. -
Page 22: Disassembly
BoardBinder. STEP 3b – Unlock by tool Unlocking and moving is made easier with our BoardBinder ReleaseTool. Ask your dealer for this tool. OnTruss Prinz Gewerbepark - Halle 78 Bozener Str. 1 86165 Augsburg / GERMANY... - Page 23 EventBoard is completely detached from the truss. If you cannot get EventBoard off the truss, probably a TrussClip Safety is attached! Please check this before you use excessive force. Otherwise the EventBoard can be damaged. OnTruss Prinz Gewerbepark - Halle 78 Bozener Str. 1...
- Page 24 It’s the same sense of rotation like a screw you turn out. For removing the TrussClips you have to turn counter-clockwise! Turning clockwise and overtightening (>90°) will damage the TrussClip. OnTruss Prinz Gewerbepark - Halle 78 Bozener Str. 1...
-
Page 25: Design Examples
Design examples OnTruss Prinz Gewerbepark - Halle 78 Bozener Str. 1 86165 Augsburg / GERMANY 25 von 27... -
Page 26: Cleaning The Eventboards
Benzine or cleaners containing ingredients such as "benzisothiazolinones" are only permitted for the EventBoard Premium. In the case of EventBoard Basic, these substances may cause visible streaks on the surface. OnTruss Prinz Gewerbepark - Halle 78 Bozener Str. 1 86165 Augsburg / GERMANY... -
Page 27: Service / Support
Please contact your dealer for further help. He will support you in any questions concerning the product and help you to handle any defects. If your dealer is not able to help you, you can also contact us directly. Contact: info@ontruss.de www.ontruss.de Address: OnTruss Prinz Gewerbepark –...