Advertisement
Advertisement
Summary of Contents for Mila Say hello to Mila
- Page 1 Mila Air User Manual Mila Say hello...
- Page 2 Safety Information Welcome to Mila! This manual provides speci ic operating instructions for your model. Use the unit only as instructed in this user manual. These instructions are not meant to cover every possi- ble condition and situation that may occur. Please practice caution and common sense when installing, operating, and maintaining any unit.
-
Page 3: Table Of Contents
Table of Contents Getting Started Definitions Operating Instructions Air Quality Modes Maintenance and Care Troubleshooting... -
Page 4: Getting Started
Getting Started Read this manual carefully Check that all parts described are included (each Mila unit comes with a corded plug and the unit itself). Pay special attention to the safety precautions! Setting up Operate your Mila in Place the air puri ier... - Page 5 “Connection Lost” screen will be control and access to the full shown until network connectivity is functionality of the system via Mila’s restored. smart phone app, available in Android and iOS. Download our Mila supports pairing with a 2.4GHz “Mila”...
-
Page 6: Definitions
AQI values above this is considered poor air quality. Refers to how often the room’s air Air Changes / Hr will be circulated through Mila's ilter every hour. The higher your ACH, the higher your fan speed. Indicates the di erence in air quality Protection Factor between indoors and outdoors. - Page 7 Terms Abbreviation What it Means Custom settings you can enable Automagic settings when Mila is in Automagic Mode. Accessible through your Mila app. Read more about the Automagic settings on p. 12. A temporary state that performs a Service Mode speci ic task.
-
Page 8: Operating Instructions
NOTE: It can take up to 90 seconds for the sensor to analyze the air quality. Each time the unit is turned on, the AUTOMAGIC Mode is activated automatically. Plug in the unit to your power outlet. Make sure your Mila Flip the power ilter door is switch located on closed. - Page 9 Operating Instructions Calibration Mode This mode starts automatically each Calibration typically takes 70 seconds time the unit boots up or the ilter door to complete and displays a countdown is removed and replaced. timer for time remaining. In this mode, the sensors are calibrating and functionality is disabled until calibration is completed.
-
Page 10: Air Quality
Air Quality This unit has an air quality sensor that analyzes the air quality. The display will show the air quality in real time. In Automagic Mode, a message bubble gives further information or analysis about the air quality level detected as shown below: Status Message What it means for your air quality Lookin' good! :) -
Page 11: Modes
Modes Tap the “Mode” button Tap the “-” or “+” button to Tap the “Mode” button (o) (o) located at the bottom change your selection. again to con irm your of the display, between mode selection. the minus (-) and plus (+) buttons. - Page 12 (this requires an Internet connection and location-sharing). This is the default mode each time your turn on your Mila. Select custom Automagic settings in the Mila app: Housekeeping Quiet Mode...
- Page 13 Modes Manual Mode To switch to manual mode follow the next steps. Tap the “Mode” button. Tap the “+” button to change the selected mode to Manual. Tap the “Mode” button again to con irm the selection. In this mode, the fan speed can be changed manually by touching the minus (-) and plus (+) buttons to increase or decrease fan speed.
-
Page 14: Maintenance And Care
Mila Sock care Wash the Mila Sock (pre ilter) by hand in cold/warm water and let dry completely before itting it back on your Mila ilter. - Page 15 Maintenance and Care Cleaning Unplug the unit before cleaning to prevent shock or ire hazards. The plastic parts of the unit may be cleaned with an oil-free dry cloth or by using a vacuum cleaner with a soft brush. Never use abrasive, harsh cleaners or wax when cleaning the unit. NOTE: The multi-layer ilter cannot be washed.
-
Page 16: Troubleshooting
Make sure your ilter is installed correctly The fan isn’t running. and the ilter door is closed properly. Restart Mila and wait for “Calibration Mode” to complete (this usually takes around 70 seconds). Mila will automatically run in “Automagic”... - Page 17 If the smell persists or if you sense a burning smell, please disconnect the puri ier and reach out to Mila Customer Care for support. The app isn’t working properly Please reach out to Mila Customer Care for support on issues related to the app.
- Page 18 My Mila just rebooted itself. time for a memory refresh (similar to how you might reset a router). Fear not, all your data is still there! For help resolving any other issues, please contact Mila Customer Care (support@milacares.com). We’d be happy to help.
Need help?
Do you have a question about the Say hello to Mila and is the answer not in the manual?
Questions and answers
How do I open the front door of my new Mila Air 3 ? Where is the latch or whatever that I need to release? I don't see it. Do I pull the bottom of the door up and out. or s;ide it up?
To open the front door of the Mila Air 3, slide the top of the filter door first, then push the magnets on the bottom of the door toward the unit.
This answer is automatically generated