Summary of Contents for OLYMP Engineering X Band Up/Downconverter
- Page 1 OLYMP Engineering LLC Add: Armenia, Yerevan 0051, Hovsep Emin 123, EIF entrance Postal Code: 0051 Attn: Orbel Sevoyan Tel: (+374) 93688597 PASSPORT X Band Up/Downconverter Yerevan, 2016...
-
Page 2: Table Of Contents
2. General product information ....................3 3. Purpose of the product ......................3 4. Technical specifications ......................3 5. General view of “X Band Up/Downconverter” ................ 5 6. Completeness ......................... 7 7. Description and operation of the product ................7 8. -
Page 3: General Information
2.1. The "X Band Up/Downconverter" is designed for round-the-clock continuous operation mode (at least 20 hours and 4 hours break) in normal climatic conditions. 2.2. Supply of the "X Band Up/Downconverter" is carried out from the source of the single-phase alternating current with a voltage of 220V and a frequency of 50Hz. - Page 4 Bandwidth 200 MHz Input Dynamic Range 50dB Input Power -50 dBm to +30 dBm Amplitude Flatness ± 0.5 dB Spurious in 200MHz BW Better than 50dBc Residual LO Power < -55 dBm VSWR Better than 1.5:1 Noise Figure 10 dB Impedance 50 Ohm Attenuator...
-
Page 5: General View Of "X Band Up/Downconverter
Operating Temperature - 55 Size (482.6 X 369.7 X 88.1) mm Weight 4 kg General view of “X Band Up/Downconverter” Fig. 1 General view of “X Band Up/Downconverter” 5.1. Dimensions Dimensions of "X Band Up/Downconverter" Height 88.1 mm ... - Page 6 Fig. 2 Dimensions of "X Band Up/Downconverter"...
-
Page 7: Completeness
7.4 The overall block diagram of the system is shown below. 220 V PROG 8-12 GHz Upconverter and Downconverter Down Up RF Up RF Down VST LO VHCDI RF Out RF In DIGITAL LO IN LO IN RF IN RF IN Fig. 3 Block diagram of the “X Band Up/Downconverter”... - Page 8 Connect the RF OUT connector of the VST RF OUT 0 to the Up RF Out of the “X Band Up/Downconverter” connector with the cable C7, Connect the Up RF Out connector of the “X Band Up/Downconverter” to the Up RF IN of the DUT connector with the cable C8, Connect the Down RF Out connector of the “X Band Up/Downconverter”...
- Page 9 Fig. 4 Connectors of “X Band Up/Downconverter” In the Table 3 are shown the “X Band Up/Downconverter” components. Table 3 Type of the connector X Band Up/Downconverter Case of the product Power switch VST VHCDI connector VHCDI...
-
Page 10: Safety Requirements
The first step of the operation is to turn on the PXI System with VST, and then the VST transceiver and the DUT. After that, pressing the "PWR" button, turn on the X Band Up/Downconverter. Safety requirements Turn on the X Band Up/Downconverter device to the network in accordance with required voltage, according to the enclosed instructions to the device. -
Page 11: Technical Service
Safety requirements before the operation Check the operability of flexible power cord, plugs, connecting cables. Clean the device from the dust with a dry, clean cloth. Check the operability of electrical socket. Safety requirements during the operation ... -
Page 12: Environment
Transport and Storage Transport and storage terms of "X Band Up/Downconverter" correspond to: 1. Terms of transportation in the part of impact: Motor transportation with a total amount of overloads no more than four: ... - Page 13 sunlight, precipitation, wind, sand and dust of the outside air, lack of or a significant decrease of the impact of diffused solar radiation and moisture condensation). 2. Terms of storage in the part of impact of climatic factors: heated and ventilated storehouses with air conditioning, located in any macroclimatic regions ...