Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for VIZRT VIZ 2110
Summary of Contents for VIZRT VIZ 2110
- Page 2 Vizrt’s policy is one of continual development, so the content of this document is periodically subject to be modified without notice. These changes will be incorporated in new editions of the publication.
-
Page 3: Table Of Contents
T A B L E O F C O N T E N T S CHAPTER 1 INTRODUCTION AND SETUP ....................3 Section 1.1 Welcome ................................... 3 Section 1.2 Overview ................................... 3 Section 1.3 Setting Up.................................. 4 1.3.1 Command and Control ..............................4 Section 1.4 Input/Output Connections ............................ -
Page 5: Chapter 1 Introduction And Setup
Viz 2110 IO. SECTION 1.1 WELCOME Thank you for purchasing this Vizrt product. As a company, Vizrt is extremely proud of its record of innovation and commitments to excellence in design, manufacture, and superb product support. We are determined to deliver the most complete, reliable and efficient integrated systems available for live production and web streaming, with capabilities suited to almost any broadcast need. -
Page 6: Section 1.3 Setting Up
Viz 2110 I/O Module Operating Instructions SECTION 1.3 SETTING UP 1.3.1 COMMAND AND CONTROL Hint: Viz 2110 IO’s interface requires a monitor resolution setting of at least 1280x1024. 1. Connect an external computer monitor to the HDMI port on the backplane (see Input/Output Connections). -
Page 7: Section 1.5 Networking
SECTION 1.6 CONFIGURATION (ADMINISTRATION) The configuration of the two SFP ports, Genlock, and (SMPTE 2110) I/O Channels is performed in Viz 2110 I/O IP’s Administration panel, shown in (Figure 2). This control panel appears on first launch, and thereafter can be accessed by selecting Exit to Admin from the Desktop (see Section 2.2.1), or from the Windows start... -
Page 8: Genlock Configuration
Viz 2110 I/O Module Operating Instructions • IPv4Address Gateway • Net Mask • Optionally, enable the Virtual LAN switch if you intend these connections to be associated with a VLAN. In this case, continue to configure the following VLAN tags: PCP –... -
Page 9: I/O Channels
Viz 2110 I/O Module Operating Instructions o Master Clock – Specify the for the Master Clock ID for genlock over IP. Video Settings – Specify the Frame Rate, Type (choose between fielded and progressive options), FIGURE 5 Width and Height. - Page 10 Viz 2110 I/O Module Operating Instructions Multicast Join Type – the membership request type when Dest IPv4 Address is a multicast address • (Audio column only) • o Audio Packet Duration –the duration of incoming audio packets o Track Count (switch) – enable this to use a value entered at right to limit the IP stream track...
-
Page 11: Administration Panel Footer Tools
Viz 2110 I/O Module Operating Instructions Dest(ination) UDP Port – the UDP port of the destination (i.e., the receiver) • RTP Payload ID – the RTP (Real-time Transfer Protocol) payload ID • (Audio column only) • o Audio Packet Duration –the duration of outgoing audio packets o Track Count (switch) –... -
Page 13: Chapter 2 User Interface
Amps, Scopes and capture. SECTION 2.1 THE DESKTOP The Viz 2110 IO IP default Desktop interface provides very useful remote monitoring options in addition to configuration and control features. The Desktop interface includes a titlebar running across the top of the screen, and a Dashboard at the bottom. -
Page 14: Configure Channels
2.1.1 CONFIGURE CHANNELS Viz 2110 IO IP allows you to select different audio and video sources for each input or channel via the Configure panel (Figure 11). Click the gear next to the channel label below a viewport to open its Configure panel (Figure 10). - Page 15 The initial Grab Directory is the default Pictures folder on the system, but you can choose to use a network FIGURE 12 storage volumes or external drive connected to one of the USB ports on your Viz 2110 IO’s rear panel instead if you like.
- Page 16 UTPUT If you open the Configure Channel pane for an output, instead, you will find settings related to output from the channel to SMPTE 2110. The first choice you will usually make is which audio/video source you wish to output as SMTPE 2110. Often, FIGURE 14 you will simply use the Audio/Video Source menu to select an NDI a/v stream from your network, but there are other possibilities, too.
- Page 17 As mentioned in the previous section, NDI sources – such as a PTZ camera with native NDI network video ® output – can be directly selected. The Video Source drop down menu also contains an Add Media item to let you select a video file to play. The Add IP Camera menu item (Figure 15) requires a little more explanation.
- Page 18 Note: After adding an IP source, you must exit and restart the software for the new settings to be applied. UPPLEMENTAL UDIO EVICE The Supplemental Audio Device allows you to direct audio output to system sound devices as well as well as FIGURE 19 any supported third part audio devices you may connect (typically by USB).
-
Page 19: Section 2.2 Titlebar & Dashboard
SECTION 2.2 TITLEBAR & DASHBOARD Viz 2110 IO’s Titlebar and Dashboard are home to a number of important displays, tools and controls. Prominently located at the top and bottom of the Desktop, the Dashboard occupies the full width of the screen. -
Page 20: Viewport Tools
Hint: You can clear individual entries using by right-clicking to show the item’s context menu, or the Clear All button in the panel’s footer. 2.2.2 VIEWPORT TOOLS Viz 2110 IO’s channels each have a toolbar beneath their respective viewports. The various elements FIGURE 24 comprising the toolbar are listed below from left to right: 1. -
Page 21: Dashboard Tools
To use an overlay, just click on an icon in the list (see Figure 28); more than one overlay can be active at the same time. FIGURE 28 2.2.3 DASHBOARD TOOLS UDIO EADPHONES You can connect a headset to the (green) audio output jack on the rear of Viz 2110 IO’s motherboard. FIGURE 29... - Page 22 Controls for Headphone audio are found in the lower-left corner of the dashboard at the bottom of the screen (Figure 29). The audio source supplied to the Headphone jack can be selected using the menu next to the headphone icon (Figure 30). 1.
-
Page 23: Appendix A: Ndi (Network Device Interface)
Vizrt systems and a growing number of third-party systems provide direct support for NDI, both for ingest and output. Although Viz 2110 IO provides many other useful features, it is purpose designed primarily to turn SMPTE 2110 sources into NDI signals and vice versa. -
Page 25: Appendix B: Third Party Licenses
APPENDIX B: THIRD PARTY LICENSES Third Party Licenses: This product uses a number of third-party software libraries under license. Related license requirements are defined in documentation installed on the product. To view these licenses, please click the Additional Licenses link provided in the Help menu on the Startup>Home page shown upon launching the product.
Need help?
Do you have a question about the VIZ 2110 and is the answer not in the manual?
Questions and answers